STM32控制SYN6288的软件设计
时间: 2023-09-25 13:12:00 浏览: 81
首先,需要明确SYN6288是一款语音识别芯片,可以通过串口与STM32进行通信。因此,需要在STM32上设计串口通信的程序。
以下是一份简单的代码示例:
```c
#include "stm32f10x.h"
#define SYN6288_RX_BUF_SIZE 128
char syn6288_rx_buf[SYN6288_RX_BUF_SIZE];
uint8_t syn6288_rx_index = 0;
void USART1_IRQHandler(void) {
if (USART_GetITStatus(USART1, USART_IT_RXNE) != RESET) {
char rx_data = USART_ReceiveData(USART1);
if (syn6288_rx_index < SYN6288_RX_BUF_SIZE) {
syn6288_rx_buf[syn6288_rx_index++] = rx_data;
}
}
}
void syn6288_send_cmd(const char* cmd) {
USART_ITConfig(USART1, USART_IT_RXNE, DISABLE);
while (*cmd) {
USART_SendData(USART1, *cmd++);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET)
;
}
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
}
void syn6288_init() {
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_USART1, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
USART_Cmd(USART1, ENABLE);
}
int main() {
syn6288_init();
// 发送指令
syn6288_send_cmd("AT+SSPEECH=0\r\n");
while (1) {
// 处理接收到的语音识别结果
if (syn6288_rx_index > 0) {
// 处理 syn6288_rx_buf
syn6288_rx_index = 0;
}
}
}
```
在上述代码中,我们使用了 USART1 进行串口通信。通过 `syn6288_init` 初始化串口,并通过 `syn6288_send_cmd` 发送指令。在 `USART1_IRQHandler` 中,我们可以处理接收到的语音识别结果。
阅读全文