STM32数码管60s倒计时显示程序
时间: 2023-07-24 10:06:15 浏览: 98
以下是一份简单的 STM32 数码管 60 秒倒计时显示程序:
```c
#include "stm32f10x.h"
#include "stm32f10x_gpio.h"
#include "stm32f10x_rcc.h"
GPIO_InitTypeDef GPIO_InitStructure;
int main(void)
{
uint8_t seconds = 60;
uint16_t display = 0;
uint16_t digit[4] = {0x3F00, 0x0600, 0x5B00, 0x4F00}; // 数码管的显示码
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3 | GPIO_Pin_4 | GPIO_Pin_5 | GPIO_Pin_6 | GPIO_Pin_7;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_10 | GPIO_Pin_11 | GPIO_Pin_12 | GPIO_Pin_13 | GPIO_Pin_14 | GPIO_Pin_15;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB, &GPIO_InitStructure);
while (1)
{
// 将秒数拆分成个位和十位
uint8_t ones = seconds % 10;
uint8_t tens = seconds / 10;
// 将显示码映射到数码管
uint16_t ones_display = digit[ones] >> 8 | digit[tens];
uint16_t tens_display = digit[ones] | digit[tens] << 8;
// 在两个数码管之间交替显示
if (display == 0)
{
GPIO_Write(GPIOA, ones_display);
GPIO_Write(GPIOB, 0x7F00);
display = 1;
}
else
{
GPIO_Write(GPIOA, tens_display);
GPIO_Write(GPIOB, 0xBF00);
display = 0;
}
// 每秒更新一次秒数
delay(1000);
seconds--;
}
}
void delay(uint32_t ms)
{
while (ms--)
{
uint32_t i = 1000;
while (i--)
;
}
}
```
在这个程序中,我们使用了 STM32 的 GPIO 来控制数码管的显示。我们首先定义了 GPIO 的初始化配置,然后在主循环中使用 `GPIO_Write` 函数来控制每个数码管的显示。
在循环中,我们将秒数拆分成个位和十位,并将每个数字的显示码映射到数码管。然后,我们在两个数码管之间交替显示这些数字。最后,我们使用 `delay` 函数来延迟一秒钟并更新秒数。
需要注意的是,这个程序是一个简单的倒计时程序,没有考虑到 STM32 的时钟频率和延迟函数的精度。在实际应用中,可能需要根据具体的情况进行调整。