Stm32f103配置串口的代码流程
时间: 2023-09-04 17:15:18 浏览: 45
以下是Stm32f103配置串口的代码流程:
1. 配置GPIO引脚
首先,需要将UART的TX和RX引脚配置为GPIO模式,并将其配置为复用推挽输出模式。例如,如果使用PA9和PA10作为UART1的TX和RX引脚:
```
/* Enable GPIO clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
/* Configure USART Tx pin as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* Configure USART Rx pin as input floating */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
```
2. 配置USART
接下来,需要配置USART控制器。需要配置波特率、数据位、停止位、奇偶校验位等参数。例如,如果使用USART1:
```
/* Enable USART clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
/* USART configuration */
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
/* Enable USART */
USART_Cmd(USART1, ENABLE);
```
3. 发送和接收数据
现在,串口已经配置好了。可以使用USART_SendData函数发送数据,使用USART_ReceiveData函数接收数据。例如,发送一个字符:
```
USART_SendData(USART1, 'A');
```
接收数据:
```
if (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == SET) {
char receivedData = USART_ReceiveData(USART1);
}
```
以上就是Stm32f103配置串口的代码流程。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)