STM32F1和SIM800连接网络调试器
时间: 2023-09-20 07:08:08 浏览: 72
连接STM32F1和SIM800模块可以使用UART串口通信。首先需要确保SIM800模块的SIM卡已经正确插入,并且已经成功连接到移动网络。然后,将STM32F1的串口TX和RX引脚分别连接到SIM800模块的RX和TX引脚上。
接下来,可以使用AT指令测试SIM800模块是否正常工作。在STM32F1中,可以通过编程方式向SIM800发送AT指令,并从SIM800接收响应消息。在调试过程中,可以使用开发板或者USB转串口工具将STM32F1连接到电脑上,使用串口调试软件(如TeraTerm、Putty等)查看调试信息。
以下是一个简单的示例代码,用于向SIM800发送AT指令并读取响应消息:
```c
#include "stm32f10x.h"
#include <string.h>
// 定义SIM800串口引脚
#define SIM800_USART USART1
#define SIM800_USART_CLK RCC_APB2Periph_USART1
#define SIM800_USART_GPIO_CLK RCC_APB2Periph_GPIOA
#define SIM800_USART_TX_PIN GPIO_Pin_9
#define SIM800_USART_TX_GPIO_PORT GPIOA
#define SIM800_USART_RX_PIN GPIO_Pin_10
#define SIM800_USART_RX_GPIO_PORT GPIOA
// 定义SIM800 AT指令
const char* AT_CMD = "AT\r\n";
void USART_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 使能串口和GPIO时钟
RCC_APB2PeriphClockCmd(SIM800_USART_CLK | SIM800_USART_GPIO_CLK, ENABLE);
// 配置USART Tx引脚为推挽输出
GPIO_InitStructure.GPIO_Pin = SIM800_USART_TX_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(SIM800_USART_TX_GPIO_PORT, &GPIO_InitStructure);
// 配置USART Rx引脚为浮空输入
GPIO_InitStructure.GPIO_Pin = SIM800_USART_RX_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(SIM800_USART_RX_GPIO_PORT, &GPIO_InitStructure);
// 配置USART
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(SIM800_USART, &USART_InitStructure);
// 使能USART
USART_Cmd(SIM800_USART, ENABLE);
}
void USART_SendString(char* str)
{
while (*str != '\0') {
// 等待发送缓冲区为空
while (USART_GetFlagStatus(SIM800_USART, USART_FLAG_TXE) == RESET);
USART_SendData(SIM800_USART, *str);
str++;
}
}
void USART_ReadString(char* buffer, uint16_t length)
{
uint16_t i = 0;
while (i < length) {
// 等待接收缓冲区非空
while (USART_GetFlagStatus(SIM800_USART, USART_FLAG_RXNE) == RESET);
buffer[i++] = USART_ReceiveData(SIM800_USART);
}
}
int main(void)
{
char response[64] = {0};
// 配置USART
USART_Configuration();
// 发送AT指令
USART_SendString((char*)AT_CMD);
// 读取响应消息
USART_ReadString(response, sizeof(response));
// 输出响应消息
printf("%s", response);
while(1);
}
```
在以上示例代码中,我们定义了SIM800模块的串口引脚和AT指令,并在main函数中发送AT指令并读取响应消息。由于SIM800模块响应消息的长度不固定,因此我们需要定义一个足够大的缓冲区来存储响应消息。