51单片机驱动MAX5414输出不同的阻值的代码
时间: 2024-01-24 11:03:35 浏览: 17
下面是一个简单的51单片机驱动MAX5414输出不同阻值的示例代码,仅供参考:
```c
#include <reg51.h>
#define CS P1_0 // MAX5414的片选引脚
#define SCK P1_1 // SPI时钟引脚
#define SDI P1_2 // SPI数据输入引脚
void delay(unsigned int n) // 延时函数
{
while (n--);
}
void send_spi_byte(unsigned char dat) // 发送一个字节的数据到MAX5414
{
unsigned char i;
for (i = 0; i < 8; i++)
{
if (dat & 0x80) SDI = 1; // 数据的最高位先发送
else SDI = 0;
SCK = 0; // 先拉低时钟线
SCK = 1; // 再拉高时钟线,让MAX5414读取数据
dat <<= 1; // 移位,准备发送下一位
}
}
void set_resistor(unsigned char reg, unsigned char val) // 设置阻值
{
CS = 0; // 选中MAX5414
send_spi_byte(0x00); // 发送控制字,选择要控制的寄存器
send_spi_byte(reg); // 发送寄存器值
send_spi_byte(val); // 发送阻值步进大小
CS = 1; // 取消选中MAX5414
}
void main()
{
unsigned char reg, val;
while (1)
{
// 设置阻值为0
reg = 0x00; // 选择第0个寄存器
val = 0x00; // 阻值步进大小为0
set_resistor(reg, val);
delay(10000); // 延时一段时间,让阻值稳定
// 设置阻值为50%
reg = 0x01; // 选择第1个寄存器
val = 0x80; // 阻值步进大小为128,对应50%的阻值
set_resistor(reg, val);
delay(10000);
// 设置阻值为100%
reg = 0x02; // 选择第2个寄存器
val = 0xFF; // 阻值步进大小为255,对应100%的阻值
set_resistor(reg, val);
delay(10000);
}
}
```
在这个示例代码中,我们使用了P1口的最低三个引脚分别连接了MAX5414的CS、SCK和SDI引脚。其中,set_resistor函数用于设置阻值,通过传入不同的寄存器值和阻值步进大小,可以实现不同的阻值输出。main函数中,我们设置了三个不同的阻值,分别为0、50%和100%,并在每个阻值设置之后延时一段时间,让阻值稳定。实际上,我们可以根据需要设置更多的阻值,只需调用set_resistor函数即可。
相关推荐
![rar](https://img-home.csdnimg.cn/images/20210720083606.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)