from fpioa_manager import fm from Maix import GPIO io_led_gre = 12 io_led_red = 13 io_led_blu = 14 fm.register(io_led_gre, fm.fpioa.GPIO0) fm.register(io_led_red, fm.fpioa.GPIO1) fm.register(io_led_blu, fm.fpioa.GPIO2) led_g = GPIO(GPIO.GPIO0, GPIO.OUT) led_r = GPIO(GPIO.GPIO1, GPIO.OUT) led_b = GPIO(GPIO.GPIO2, GPIO.OUT) for i in range(80): # 闪烁10轮 led_g.value(i//4%2) led_r.value(i//2%2) led_b.value(i%2) for j in range(200000): # 用来消耗时间 k = 1
时间: 2023-04-07 10:03:07 浏览: 118
这段代码是在使用Maix开发板上的GPIO控制LED灯。首先通过fpioa_manager模块的fm函数来注册三个GPIO引脚,分别对应绿、红、蓝三种颜色的LED灯。然后通过Maix模块的GPIO函数来初始化这三个引脚,并将它们设置为输出模式。最后通过for循环来控制LED灯的闪烁,循环80次。
相关问题
Maix_bit 如何裁切图像
Maix_bit 是一款基于 Kendryte K210 芯片的 AI 模块,可以使用其搭载的 Kendryte KPU 进行图像裁剪。以下是 Maix_bit 裁剪图像的基本步骤:
1. 使用 MaixPy IDE 连接到 Maix_bit。
2. 导入必要的库:`from fpioa_manager import fm, board_info`,`import sensor`,`import image`。
3. 初始化摄像头:`sensor.reset()`,`sensor.set_pixformat(sensor.RGB565)`,`sensor.set_framesize(sensor.QVGA)`,`sensor.skip_frames(time = 2000)`。
4. 从摄像头获取图像:`img = sensor.snapshot()`。
5. 使用 `img` 对象的 `sub_image()` 方法进行裁剪,该方法接受四个参数:`x`,`y`,`w`,`h`,分别表示裁剪图像的左上角坐标和宽高。
6. 在 MaixPy IDE 的 REPL 中使用 `img.show()` 方法查看裁剪后的图像。
例如,裁剪图像的左上角坐标为 (20, 30),宽度为 100,高度为 80,代码如下:
```python
from fpioa_manager import fm, board_info
import sensor
import image
sensor.reset()
sensor.set_pixformat(sensor.RGB565)
sensor.set_framesize(sensor.QVGA)
sensor.skip_frames(time = 2000)
img = sensor.snapshot()
x, y = 20, 30
w, h = 100, 80
crop_img = img.sub_image(x, y, w, h)
crop_img.show()
```
注意,在裁剪图像时,需要保证裁剪后的图像坐标和宽高不会超出原始图像的范围。
from Maix import GPIO
The code snippet you provided imports the GPIO module from the Maix library. This module is used for interacting with the General Purpose Input/Output (GPIO) pins on Maix boards. With this module, you can control and read the state of GPIO pins, configure their modes, and perform other operations related to GPIO.
Please note that the Maix library may be specific to certain development boards or platforms. Make sure you have the necessary dependencies and hardware support to use the GPIO module from Maix.