51单片机C语言访问外ram,C51中访问外部RAM的方法
时间: 2024-02-11 18:07:14 浏览: 29
在51单片机中,要访问外部RAM,需要先在程序中定义外部RAM的地址范围,然后使用指针来访问这段地址范围。具体步骤如下:
1. 在程序中定义外部RAM的地址范围,可以使用以下语句:
```
#define EXT_RAM_START 0x8000 /* 外部RAM起始地址 */
#define EXT_RAM_SIZE 0x8000 /* 外部RAM大小 */
__xdata __at (EXT_RAM_START) unsigned char ext_ram[EXT_RAM_SIZE];
```
这里使用__xdata关键字定义了一个存储在外部RAM中的unsigned char类型数组ext_ram,它的起始地址是EXT_RAM_START,大小为EXT_RAM_SIZE。
2. 然后在程序中使用指针来访问外部RAM,可以使用以下语句:
```
unsigned char *p_ext_ram = ext_ram;
```
这里定义了一个指向ext_ram数组的指针p_ext_ram,使用指针访问外部RAM时,可以使用*p_ext_ram来访问外部RAM中的数据。例如:
```
*p_ext_ram = 0x55; /* 将0x55写入外部RAM的第一个字节 */
```
需要注意的是,在使用外部RAM时,需要在程序中设置相关的寄存器,例如P4口设置为外部RAM地址线,还需要设置片内RAM的地址范围,以免与外部RAM地址重叠。具体的设置方法可以参考单片机的数据手册。
相关问题
写一个将7-16存入片外RAM的连续10个细节地址2000H-2009H中的单片机C语言
以下是一个将 7-16 存入片外 RAM 的连续 10 个地址 2000H-2009H 中的单片机 C 语言程序示例,假设片外 RAM 的地址为 0x8000:
```c
#include <reg52.h>
void main() {
unsigned char i;
unsigned int addr = 0x8000; // 片外 RAM 的起始地址为 0x8000
unsigned char data[10] = {7, 8, 9, 10, 11, 12, 13, 14, 15, 16}; // 存储的数据
for (i = 0; i < 10; i++) {
*(unsigned char *)(addr + i) = data[i]; // 将数据存入片外 RAM 的连续地址中
}
}
```
以上程序使用了 Keil C51 编译器,使用了指针的方式直接访问片外 RAM 的地址,并将数据存储到其中。具体的实现方式可能会因为单片机型号和编程语言的不同而有所差异,但以上代码可以作为参考。
基于STC89C51单片机,每当KEY按下时,将片内RAM30H单元的内容加1,利用外部中断1实现,请用C语言编程实现
Sure! Here's a C code snippet to implement the functionality you described using the STC89C51 microcontroller and external interrupt 1:
```c
#include <reg51.h>
#define RAM_ADDRESS 0x30 // RAM address to increment
void externalInterrupt1() interrupt 2 {
P3 = RAM_ADDRESS; // Set the address to access RAM
A = P0; // Read the current value from RAM
A++; // Increment the value
P0 = A; // Write the updated value back to RAM
}
void main() {
IT1 = 1; // Configure external interrupt 1 as falling edge triggered
EX1 = 1; // Enable external interrupt 1
EA = 1; // Enable global interrupts
while(1) {
// Your main code here
}
}
```
In this code, we define the RAM address (`RAM_ADDRESS`) to be incremented as `0x30`. The `externalInterrupt1()` function is the interrupt service routine (ISR) for external interrupt 1. When the interrupt is triggered (i.e., when the KEY is pressed), this ISR is executed. Inside the ISR, we set `P3` to `RAM_ADDRESS` to access the desired RAM location. We read the current value from that location, increment it, and write the updated value back to RAM.
In the main function, we configure external interrupt 1 as falling edge triggered (`IT1 = 1`) and enable it (`EX1 = 1`). We also enable global interrupts (`EA = 1`). You can add your main code inside the while loop.
Please note that this code assumes you have already set up the necessary hardware connections and initializations for the microcontroller.