HAL_GPIO_WritePin函数怎么用
时间: 2024-05-25 22:15:10 浏览: 24
HAL_GPIO_WritePin函数是针对STM32芯片的,用于控制单片机的GPIO口的电平状态。它的用法是:
HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState)
其中,GPIOx是GPIO口所在的寄存器组,GPIO_Pin是对应的引脚,PinState则是要设置的电平状态,可选项为GPIO_PIN_RESET(低电平)和GPIO_PIN_SET(高电平)。例如,如果要将PA5引脚设置为高电平状态,代码应该如下所示:
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET)
相关问题
hal_gpio_writepin函数用途
hal_gpio_writepin函数是用于控制单片机GPIO口输出的函数。下面是该函数的参数说明:
函数原型:void hal_gpio_writepin(hal_gpio_pin_t pin, uint32_t value)
参数:
- pin:GPIO引脚编号,类型为hal_gpio_pin_t,需要根据实际硬件来指定。
- value:GPIO引脚输出的电平,类型为uint32_t,可以是0或1。
函数功能:
该函数用于控制GPIO引脚的输出电平,将value的值写入到pin对应的引脚上。
示例代码:
以下是一个简单的示例代码,用于将PA5引脚的输出电平设置为高电平。
```c
#include "stm32f1xx_hal.h"
// 定义PA5引脚
#define LED_Pin GPIO_PIN_5
#define LED_GPIO_Port GPIOA
int main(void)
{
// 初始化HAL库
HAL_Init();
// 配置GPIO引脚为输出模式
GPIO_InitTypeDef GPIO_InitStruct = {0};
GPIO_InitStruct.Pin = LED_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(LED_GPIO_Port, &GPIO_InitStruct);
// 设置PA5引脚输出高电平
HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_SET);
while (1)
{
}
}
```
HAL_GPIO_WritePin的使用
HAL_GPIO_WritePin函数用于写入GPIO引脚的状态,即将GPIO引脚设置为高电平或低电平。使用该函数需要先初始化相应的GPIO引脚。
函数原型:
```c
void HAL_GPIO_WritePin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState);
```
参数说明:
- GPIOx:GPIO端口号,例如GPIOA,GPIOB等。
- GPIO_Pin:GPIO引脚号,取值范围为GPIO_PIN_0~GPIO_PIN_15。
- PinState:GPIO引脚状态,取值为GPIO_PIN_RESET或GPIO_PIN_SET。
使用示例:
下面的示例演示如何使用HAL_GPIO_WritePin函数将GPIO引脚设置为高电平或低电平。
```c
#include "main.h"
int main(void)
{
HAL_Init();
/* 使能GPIOA时钟 */
__HAL_RCC_GPIOA_CLK_ENABLE();
/* 配置PA5引脚为输出模式 */
GPIO_InitTypeDef GPIO_InitStruct;
GPIO_InitStruct.Pin = GPIO_PIN_5;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
while (1)
{
/* 将PA5引脚设置为高电平 */
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_SET);
/* 延时 */
HAL_Delay(1000);
/* 将PA5引脚设置为低电平 */
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_5, GPIO_PIN_RESET);
/* 延时 */
HAL_Delay(1000);
}
}
```
在上面的示例中,我们首先使能了GPIOA的时钟,然后将PA5引脚配置为输出模式。在while循环中,我们使用HAL_GPIO_WritePin函数将PA5引脚的状态设置为高电平或低电平,并延时1秒钟。这样就能够实现GPIO引脚的控制了。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)