使用keil写一个当接收到高电平时,显示文字
时间: 2023-11-27 16:51:35 浏览: 28
假设你的开发板使用的是STM32系列的单片机,以下是一个基于Keil的示例代码:
```c
#include <stm32f10x.h>
#include <stdio.h>
void USART1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 使能USART1和GPIOA口的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
// 配置USART1的Tx引脚为复用推挽输出
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置USART1的Rx引脚为浮空输入
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置USART1
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 使能USART1
USART_Cmd(USART1, ENABLE);
}
void USART1_SendString(char* str)
{
while (*str)
{
USART_SendData(USART1, *str++);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
}
}
int main()
{
char buffer[64];
// 初始化USART1口
USART1_Init();
// 利用PA0引脚作为输入口
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
while (1)
{
if (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0) == Bit_SET)
{
sprintf(buffer, "高电平已接收\n");
USART1_SendString(buffer);
while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0) == Bit_SET);
}
}
}
```
在上述代码中,我们使用PA0口作为输入口,如果检测到高电平,就通过USART1口输出一段文字。函数`USART1_Init()`用于初始化USART1口,函数`USART1_SendString()`用于通过USART1口输出字符串。注意要在Keil中配置正确的芯片型号和芯片时钟频率,否则代码可能无法正常运行。