ensp mstp主备根桥
时间: 2023-11-29 11:47:49 浏览: 67
为了实现MSTP主备根桥的配置,需要在MSTP实例中选择一个交换机作为主根交换机,另一个交换机作为备用根交换机。在MSTP实例中,每个实例都有一个主根交换机和一个备用根交换机。主根交换机是MSTP实例中的根交换机,而备用根交换机是次优根交换机。在MSTP实例中,主根交换机和备用根交换机的选择是基于优先级和MAC地址的。具体步骤如下:
1. 配置SwitchA为MSTI1的主根交换机。
```shell
stp instance 1 root primary
```
2. 配置SwitchB为MSTI2的备用根交换机。
```shell
stp instance 2 root secondary
```
相关问题
ensp mstp配置
ENSP(Enterprise Network Simulation Platform)是华为公司推出的一款网络仿真软件,可以模拟各种网络设备和拓扑,方便网络工程师进行实验和测试。MSTP(Multiple Spanning Tree Protocol)是一种支持多个 VLAN 的生成树协议。
下面是在 ENSP 中配置 MSTP 的步骤:
1. 在 ENSP 中创建一个新的拓扑,并添加需要配置 MSTP 的设备(如三台交换机)。
2. 在每台交换机上启用 MSTP 协议:
```
<Switch> system-view
[Switch] stp enable
[Switch] stp mode mstp
```
3. 配置 MSTP 的根桥(Root Bridge)。一般情况下,选择连接各个交换机的核心交换机作为根桥。
```
[Switch] stp region-configuration
[Switch-region-mstp] revision-level 1
[Switch-region-mstp] instance 1 vlan 1 to 4094
[Switch-region-mstp-instance-1-vlan-1-4094] root primary
```
4. 配置每个交换机的优先级,以确定生成树中的根交换机。优先级越低的交换机越可能成为根交换机。
```
[Switch] stp priority 4096
```
5. 配置各个端口的 VLAN,并启用 MSTP。
```
[Switch] vlan 10
[Switch-vlan10] quit
[Switch] interface gigabitethernet0/0/1
[Switch-GigabitEthernet0/0/1] port link-type access
[Switch-GigabitEthernet0/0/1] port default vlan 10
[Switch-GigabitEthernet0/0/1] stp edged-port enable
[Switch-GigabitEthernet0/0/1] stp sharp
[Switch-GigabitEthernet0/0/1] quit
[Switch] stp enable
```
以上是 MSTP 在 ENSP 中的基本配置步骤,具体配置根据实际情况而定。
ensp mstp和vrrp配置实例
ensp mstp是指Ethernet Network Service Provider Multiple Spanning Tree Protocol,它是一种用于在以太网网络中实现多重树协议的技术。MSTP使用多个生成树来分解网络拓扑,以提高网络的可靠性和性能。
vrrp是指Virtual Router Redundancy Protocol,它是一种用于在网络中实现虚拟路由器冗余的协议。VRRP允许将多个物理路由器组成一个虚拟路由器,以实现路由器的高可用性和无故障切换。
下面是ensp mstp和vrrp的配置实例:
1.ensp mstp配置实例:
- 配置MSTP实例参数:
mstp instance <instance-id> vlan <vlan-id>
- 配置MSTP根桥:
stp root primary|secondary
- 配置MSTP边桥:
stp bridge <bridge-id> priority <priority>
- 配置MSTP端口:
interface <interface-id>
stp edged-port enable|disable
2.vrrp配置实例:
- 配置VRRP组:
interface <interface-id>
vrrp vrid <vrid> virtual-ip <virtual-ip>
- 配置VRRP优先级:
vrrp vrid <vrid> priority <priority>
- 配置VRRP追随者优先级:
vrrp vrid <vrid> follower-priority <follower-priority>
- 配置VRRP追随者路由器ID:
vrrp vrid <vrid> follower-id <follower-id>