给我一个基于stm32f103的两一路ADC采样并通过一路DAC输出的keil程序

下面是一个基于STM32F103的双路ADC采样并通过一路DAC输出的Keil程序示例，你可以参考一下：

#include "stm32f10x.h"

#define ADC1_DR_Address ((uint32_t)0x4001244C)

__IO uint16_t ADC1ConvertedValue = 0, ADC1ConvertedVoltage = 0;
__IO uint16_t ADC2ConvertedValue = 0, ADC2ConvertedVoltage = 0;

void ADC1_GPIO_Config(void);
void ADC2_GPIO_Config(void);
void ADC1_Mode_Config(void);
void ADC2_Mode_Config(void);
void DAC_Config(void);
void Delay(__IO uint32_t nCount);

int main(void)
{
  ADC1_GPIO_Config();
  ADC2_GPIO_Config();
  ADC1_Mode_Config();
  ADC2_Mode_Config();
  DAC_Config();

  while (1)
  {
    ADC_SoftwareStartConvCmd(ADC1, ENABLE);
    while (!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC));
    ADC1ConvertedValue = ADC_GetConversionValue(ADC1);
    ADC1ConvertedVoltage = (ADC1ConvertedValue * 3300) / 0xFFF;

    ADC_SoftwareStartConvCmd(ADC2, ENABLE);
    while (!ADC_GetFlagStatus(ADC2, ADC_FLAG_EOC));
    ADC2ConvertedValue = ADC_GetConversionValue(ADC2);
    ADC2ConvertedVoltage = (ADC2ConvertedValue * 3300) / 0xFFF;

    DAC_SetChannel1Data(DAC_Align_12b_R, ADC1ConvertedValue);
    DAC_SoftwareTriggerCmd(DAC_Channel_1, ENABLE);
    
    Delay(0xFFFFF);
  }
}

void ADC1_GPIO_Config(void)
{
  GPIO_InitTypeDef GPIO_InitStructure;
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_ADC1, ENABLE);

  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
  GPIO_Init(GPIOA, &GPIO_InitStructure);
}

void ADC2_GPIO_Config(void)
{
  GPIO_InitTypeDef GPIO_InitStructure;
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_ADC2, ENABLE);

  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
  GPIO_Init(GPIOA, &GPIO_InitStructure);
}

void ADC1_Mode_Config(void)
{
  ADC_InitTypeDef ADC_InitStructure;

  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);

  ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
  ADC_InitStructure.ADC_ScanConvMode = DISABLE;
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
  ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_NbrOfChannel = 1;

  ADC_Init(ADC1, &ADC_InitStructure);

  ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_55Cycles5);

  ADC_Cmd(ADC1, ENABLE);

  ADC_ResetCalibration(ADC1);
  while (ADC_GetResetCalibrationStatus(ADC1));

  ADC_StartCalibration(ADC1);
  while (ADC_GetCalibrationStatus(ADC1));
}

void ADC2_Mode_Config(void)
{
  ADC_InitTypeDef ADC_InitStructure;

  RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);

  ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
  ADC_InitStructure.ADC_ScanConvMode = DISABLE;
  ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
  ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
  ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
  ADC_InitStructure.ADC_NbrOfChannel = 1;

  ADC_Init(ADC2, &ADC_InitStructure);

  ADC_RegularChannelConfig(ADC2, ADC_Channel_1, 1, ADC_SampleTime_55Cycles5);

  ADC_Cmd(ADC2, ENABLE);

  ADC_ResetCalibration(ADC2);
  while (ADC_GetResetCalibrationStatus(ADC2));

  ADC_StartCalibration(ADC2);
  while (ADC_GetCalibrationStatus(ADC2));
}

void DAC_Config(void)
{
  GPIO_InitTypeDef GPIO_InitStructure;
  DAC_InitTypeDef DAC_InitStructure;

  RCC_APB1PeriphClockCmd(RCC_APB1Periph_DAC, ENABLE);
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);

  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  DAC_InitStructure.DAC_Trigger = DAC_Trigger_None;
  DAC_InitStructure.DAC_WaveGeneration = DAC_WaveGeneration_None;
  DAC_InitStructure.DAC_OutputBuffer = DAC_OutputBuffer_Enable;
  DAC_Init(DAC_Channel_1, &DAC_InitStructure);

  DAC_Cmd(DAC_Channel_1, ENABLE);
}

void Delay(__IO uint32_t nCount)
{
  while (nCount--)
  {
  }
}

需要注意的是，这个程序只是一个示例，你需要根据实际的硬件连接情况进行调整和修改。同时，如果你使用的是不同型号或者不同版本的STM32芯片，也需要修改一些配置项。