写一个stm32f103c8t6在OLED屏上显示的代码
时间: 2023-04-08 17:03:59 浏览: 84
我可以回答这个问题。以下是一个简单的示例代码,可以在STM32F103C8T6上使用OLED屏幕显示Hello World:
```
#include "stm32f10x.h"
#include "oled.h"
int main(void)
{
OLED_Init(); // 初始化OLED屏幕
OLED_Clear(); // 清空屏幕
OLED_ShowString(0, 0, "Hello World!"); // 在屏幕上显示Hello World
while (1)
{
}
}
```
请注意,这只是一个简单的示例代码,您需要根据您的具体需求进行修改和优化。
相关问题
stm32f103c8t6连接oled 屏幕
要连接STM32F103C8T6与OLED屏幕,您需要遵循以下步骤:
1. 确定您的OLED屏幕模块所使用的接口类型(如SPI或I2C)以及其引脚分配。
2. 在STM32F103C8T6上配置相应的引脚为SPI或I2C接口,并将其连接到OLED屏幕上的相应引脚。
3. 寻找适当的OLED驱动程序库。有很多开源的驱动程序库可供选择,例如Adafruit_SSD1306、u8glib等。选择一个适合您的OLED屏幕和STM32F103C8T6的库,并将其添加到您的工程中。
4. 在您的代码中初始化OLED驱动程序库,并将其配置为与您的OLED屏幕兼容。
5. 编写代码以控制OLED屏幕,例如绘制图形、显示文本等。
6. 将您的STM32F103C8T6与OLED屏幕进行连接测试,并根据需要进行调整。
这只是一个基本的步骤指南,具体操作细节会因您所使用的OLED屏幕和STM32F103C8T6而有所不同。在进行连接和编程之前,建议您参考OLED屏幕和STM32F103C8T6的数据手册和相关的示例代码。
写一个用STM32F103C8T6通过OLED初始化的代码
### 回答1:
以下是STM32F103C8T6通过OLED初始化的代码示例,这是一个C语言的实现。它初始化了128x64的OLED显示器,使用I2C通信。
```
#include "stm32f10x.h"
#include "stdio.h"
#include "string.h"
#include "oled.h"
#define OLED_SCL_L() GPIO_ResetBits(GPIOB,GPIO_Pin_10)//SCL
#define OLED_SCL_H() GPIO_SetBits(GPIOB,GPIO_Pin_10)
#define OLED_SDA_L() GPIO_ResetBits(GPIOB,GPIO_Pin_11)//SDA
#define OLED_SDA_H() GPIO_SetBits(GPIOB,GPIO_Pin_11)
#define OLED_SDA_Read() GPIO_ReadInputDataBit(GPIOB,GPIO_Pin_11)
/**********定义字符点阵**********/
const unsigned char F8X16[]=
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,
0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x00,
0x00,0x10,0x20,0x7F,0x20,0x10,0x00,0x00,0x00,0x04,0x0E,0x1F,0x0E,0x04,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00,0x00,
0x00,0x00,0x00,0x7C,0x60,0x7C,0x60,0x
### 回答2:
#include "stm32f10x.h"
#include "stdlib.h" // 包含stdlib头文件用于使用malloc函数
#define SCREEN_WIDTH 128
#define SCREEN_HEIGHT 64
// 定义OLED引脚连接的引脚
#define OLED_SCL_PORT GPIOB
#define OLED_SCL_PIN GPIO_Pin_6
#define OLED_SDA_PORT GPIOB
#define OLED_SDA_PIN GPIO_Pin_7
#define OLED_RST_PORT GPIOB
#define OLED_RST_PIN GPIO_Pin_8
// OLED初始化函数声明
void OLED_Init(void);
int main(void)
{
// 启动OLED屏幕初始化
OLED_Init();
while(1)
{
// 在这里可以编写其他逻辑代码
}
}
void Delay_ms(uint32_t ms)
{
uint32_t i;
for(i=0;i<ms;i++)
{
int j=50000;
while(j--)
{
__NOP();
}
}
}
void IIC_Start(void)
{
GPIO_SetBits(OLED_SCL_PORT, OLED_SCL_PIN); // 拉高时钟线
GPIO_SetBits(OLED_SDA_PORT, OLED_SDA_PIN); // 拉高数据线
Delay_ms(2);
GPIO_ResetBits(OLED_SDA_PORT, OLED_SDA_PIN); // 拉低数据线
Delay_ms(2);
GPIO_ResetBits(OLED_SCL_PORT, OLED_SCL_PIN); // 拉低时钟线
Delay_ms(2);
}
void IIC_Stop(void)
{
GPIO_SetBits(OLED_SCL_PORT, OLED_SCL_PIN); // 拉高时钟线
GPIO_ResetBits(OLED_SDA_PORT, OLED_SDA_PIN); // 拉低数据线
Delay_ms(2);
GPIO_SetBits(OLED_SDA_PORT, OLED_SDA_PIN); // 拉高数据线
Delay_ms(2);
}
void Write_IIC_Command(uint8_t cmd)
{
GPIO_ResetBits(OLED_SCL_PORT, OLED_SCL_PIN); // 拉低时钟线
for (uint8_t i = 0; i < 8; i++)
{
if ((cmd & 0x80) == 0x80)
{
GPIO_SetBits(OLED_SDA_PORT, OLED_SDA_PIN); // 拉高数据线
}
else
{
GPIO_ResetBits(OLED_SDA_PORT, OLED_SDA_PIN); // 拉低数据线
}
Delay_ms(2);
GPIO_SetBits(OLED_SCL_PORT, OLED_SCL_PIN); // 拉高时钟线
Delay_ms(2);
GPIO_ResetBits(OLED_SCL_PORT, OLED_SCL_PIN); // 拉低时钟线
Delay_ms(2);
cmd <<= 1;
}
}
void OLED_Init(void)
{
// 初始化GPIO引脚
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
GPIO_InitStructure.GPIO_Pin = OLED_SCL_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(OLED_SCL_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = OLED_SDA_PIN;
GPIO_Init(OLED_SDA_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = OLED_RST_PIN;
GPIO_Init(OLED_RST_PORT, &GPIO_InitStructure);
// 片选OLED显示模块
GPIO_SetBits(OLED_RST_PORT, OLED_RST_PIN);
Delay_ms(100);
GPIO_ResetBits(OLED_RST_PORT, OLED_RST_PIN);
Delay_ms(100);
GPIO_SetBits(OLED_RST_PORT, OLED_RST_PIN);
// OLED初始化
Write_IIC_Command(0xAE); // 关闭显示
Write_IIC_Command(0x20); // 设置寻址模式(0x00:列地址模式,0x02:页地址模式)
Write_IIC_Command(0x10); // 设置列地址 启始点为0x02 0x00~0x07启示点
Write_IIC_Command(0xB0); // 设置页地址(0xB0~0xB7)
Write_IIC_Command(0xC8); // 设置COM映射方式(0xC0:COM0为地位,0xC8:COM0为高位)
Write_IIC_Command(0x00); // 设置低列地址
Write_IIC_Command(0x10); // 设置高列地址
Write_IIC_Command(0x40); // 设置起始行地址
Write_IIC_Command(0x81); // 设置对比度控制寄存器
Write_IIC_Command(0xCF); // 设置对比度(0x00~0xFF)
Write_IIC_Command(0xA1); // 设置段重定义(0xA0:列地址0~127,0xA1:列地址127~0)
Write_IIC_Command(0xA4); // 设置显示全部点亮(不设置显示全部点亮:0xA4)
Write_IIC_Command(0xA6); // 设置非反显模式(0xA6:正显,0xA7:反显)
Write_IIC_Command(0xAF); // 打开显示
}
### 回答3:
以下是一个使用STM32F103C8T6通过OLED初始化的示例代码:
```c
#include "stm32f1xx.h"
#include "OLED.h"
GPIO_InitTypeDef GPIO_InitStruct;
void GPIO_Configuration(void)
{
__HAL_RCC_GPIOC_CLK_ENABLE();
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Pin = GPIO_PIN_13;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
}
void SPI_Configuration(void)
{
__HAL_RCC_SPI1_CLK_ENABLE();
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Pin = GPIO_PIN_5 | GPIO_PIN_7;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_6;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
hspi1.Instance = SPI1;
hspi1.Init.Mode = SPI_MODE_MASTER;
hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2;
hspi1.Init.Direction = SPI_DIRECTION_2LINES;
hspi1.Init.CLKPhase = SPI_PHASE_1EDGE;
hspi1.Init.CLKPolarity = SPI_POLARITY_LOW;
hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE;
hspi1.Init.CRCPolynomial = 7;
HAL_SPI_Init(&hspi1);
}
void OLED_Init(void)
{
GPIO_Configuration();
SPI_Configuration();
HAL_GPIO_WritePin(GPIOC, GPIO_PIN_13, GPIO_PIN_RESET);
HAL_Delay(10);
HAL_GPIO_WritePin(GPIOC, GPIO_PIN_13, GPIO_PIN_SET);
HAL_Delay(10);
HAL_SPI_Transmit(&hspi1, (uint8_t *)OLED_InitData, sizeof(OLED_InitData), HAL_MAX_DELAY);
HAL_Delay(10);
HAL_SPI_Transmit(&hspi1, (uint8_t *)OLED_SetPositionData, sizeof(OLED_SetPositionData), HAL_MAX_DELAY);
HAL_Delay(10);
HAL_SPI_Transmit(&hspi1, (uint8_t *)OLED_DisplayOnData, sizeof(OLED_DisplayOnData), HAL_MAX_DELAY);
HAL_Delay(10);
}
int main(void)
{
HAL_Init();
OLED_Init();
while (1)
{
// 在这里添加你的代码
}
}
```
此示例代码基于STM32的HAL库编写,并通过SPI与OLED通信。在初始化过程中,先设置了GPIO和SPI的配置信息,然后通过SPI与OLED通信发送初始化命令和显示控制命令,实现OLED的初始化操作。接下来,你可以在 `while (1)` 循环中添加自己的代码来控制OLED显示内容。请注意,代码中的 `OLED_InitData`、`OLED_SetPositionData` 和 `OLED_DisplayOnData` 是预先定义好的OLED初始化数据。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)