ds1302万年历程序设计c语言
时间: 2023-08-18 21:07:21 浏览: 49
以下是使用C语言编写DS1302万年历程序的基本步骤:
1. 定义DS1302的IO口连接,包括CLK、DAT和RST。
2. 初始化DS1302,包括设置时钟、日期和闹钟等参数。
3. 读取当前的时钟、日期和闹钟等参数,并在LCD屏幕上显示。
4. 实现按键功能,包括调整时钟、日期和闹钟等参数,以及开启/关闭闹钟功能。
5. 实现时钟功能,即每秒钟更新一次时钟,并在LCD屏幕上显示。
6. 实现闹钟功能,即在设定的时间到达时触发闹钟,并在LCD屏幕上显示提示信息。
7. 循环执行以上步骤,直到程序结束。
需要注意的是,DS1302的读写操作需要在时序上满足一定的要求,否则会导致读写失败。因此,在程序中需要加入一些延时函数或者使用定时器来控制时序,以保证DS1302能够正常工作。
相关问题
DS1302写数据代码 用c语言写
以下是 DS1302 写入数据的 C 语言代码示例,仅供参考:
```C
#include <stdio.h>
#include <stdlib.h>
#include <wiringPi.h>
#include <wiringPiSPI.h>
#define DS1302_RST_PIN 0
#define DS1302_DAT_PIN 1
#define DS1302_CLK_PIN 2
#define DS1302_CMD_WRITE 0x80 // 写入命令
#define DS1302_CMD_READ 0x81 // 读取命令
#define DS1302_ADDR_SECOND 0x80 // 秒地址
#define DS1302_ADDR_MINUTE 0x82 // 分钟地址
#define DS1302_ADDR_HOUR 0x84 // 小时地址
#define DS1302_ADDR_DATE 0x86 // 日地址
#define DS1302_ADDR_MONTH 0x88 // 月份地址
#define DS1302_ADDR_DAY 0x8A // 星期地址
#define DS1302_ADDR_YEAR 0x8C // 年份地址
void DS1302_WriteByte(unsigned char cmd)
{
unsigned char i;
for(i = 0; i < 8; i++)
{
digitalWrite(DS1302_CLK_PIN, LOW);
digitalWrite(DS1302_DAT_PIN, cmd & 0x01);
cmd >>= 1;
digitalWrite(DS1302_CLK_PIN, HIGH);
}
}
void DS1302_Write(unsigned char addr, unsigned char data)
{
digitalWrite(DS1302_RST_PIN, HIGH);
DS1302_WriteByte(DS1302_CMD_WRITE | addr);
DS1302_WriteByte(data);
digitalWrite(DS1302_RST_PIN, LOW);
}
void DS1302_Init()
{
pinMode(DS1302_RST_PIN, OUTPUT);
pinMode(DS1302_DAT_PIN, OUTPUT);
pinMode(DS1302_CLK_PIN, OUTPUT);
digitalWrite(DS1302_RST_PIN, LOW);
digitalWrite(DS1302_CLK_PIN, LOW);
DS1302_Write(DS1302_ADDR_YEAR, 21); // 年份
DS1302_Write(DS1302_ADDR_MONTH, 9); // 月份
DS1302_Write(DS1302_ADDR_DATE, 23); // 日
DS1302_Write(DS1302_ADDR_DAY, 3); // 星期三
DS1302_Write(DS1302_ADDR_HOUR, 12); // 小时
DS1302_Write(DS1302_ADDR_MINUTE, 30); // 分钟
DS1302_Write(DS1302_ADDR_SECOND, 0); // 秒
}
void DS1302_SetTime(unsigned char hour, unsigned char minute, unsigned char second)
{
DS1302_Write(DS1302_ADDR_HOUR, hour);
DS1302_Write(DS1302_ADDR_MINUTE, minute);
DS1302_Write(DS1302_ADDR_SECOND, second);
}
void DS1302_SetDate(unsigned char year, unsigned char month, unsigned char date)
{
DS1302_Write(DS1302_ADDR_YEAR, year);
DS1302_Write(DS1302_ADDR_MONTH, month);
DS1302_Write(DS1302_ADDR_DATE, date);
}
int main()
{
wiringPiSetup();
DS1302_Init();
while(1)
{
DS1302_SetTime(12, 31, 30); // 设置时分秒
DS1302_SetDate(21, 9, 23); // 设置年月日
delay(1000);
}
return 0;
}
```
在程序中,首先需要定义 DS1302 的 RST、DAT 和 CLK 引脚,以及写入和读取命令和各个数据地址。在 `DS1302_WriteByte()` 函数中,通过 CLK 引脚和 DAT 引脚来模拟 SPI 通信,将写入的数据字节传输给 DS1302。
在 `DS1302_Write()` 函数中,先将 RST 引脚拉高,然后通过 `DS1302_WriteByte()` 函数向 DS1302 中写入命令和数据。在 `DS1302_Init()` 函数中,设置 DS1302 的初始时间和日期。
在 `DS1302_SetTime()` 和 `DS1302_SetDate()` 函数中,分别向对应的数据地址中写入时分秒和年月日数据。
在 `main()` 函数中,循环调用 `DS1302_SetTime()` 和 `DS1302_SetDate()` 函数,每隔一秒钟更新一次时间和日期。
单片机万年历程序设计程序代码
以下是一个基于51单片机的简单万年历程序设计的代码:
```
#include<reg52.h>
#include<intrins.h>
typedef unsigned char uchar;
typedef unsigned int uint;
uchar code table[] = {0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71}; //共阴数码管0~9 a~f
uchar year, month, day;
uchar week; //定义年月日和星期
uchar dis_1,dis_2,dis_3,dis_4; //定义四个数码管的显示值
void delay(uint z) //延时函数
{
uint x,y;
for(x=z;x>0;x--)
for(y=110;y>0;y--);
}
void get_time() //获取时间函数
{
uchar temp;
temp = DS1302_Read(0x86);
year = DS1302_Read(0x86);
month = DS1302_Read(0x88);
day = DS1302_Read(0x8A);
week = DS1302_Read(0x8C);
year = year + 2000;
}
void main()
{
TMOD = 0x01; //定时器0工作模式,16位计数
TH0 = 0xFA; //赋初值
TL0 = 0xCD;
TR0 = 1; //开启定时器0
ET0 = 1; //开启定时器0中断
EA = 1; //开启总中断
while(1)
{
get_time(); //获取时间
dis_1 = year / 1000; //计算千位数码管的值
dis_2 = (year % 1000) / 100; //计算百位数码管的值
dis_3 = (year % 100) / 10; //计算十位数码管的值
dis_4 = year % 10; //计算个位数码管的值
P2 = 0x00; //清空P2口
P0 = table[dis_1]; //显示千位数码管的值
P2 = 0x01; //P2.0口输出高电平,点亮千位数码管
delay(2); //延时一段时间,防止闪烁
P2 = 0x00;
P0 = table[dis_2];
P2 = 0x02;
delay(2);
P2 = 0x00;
P0 = table[dis_3];
P2 = 0x04;
delay(2);
P2 = 0x00;
P0 = table[dis_4];
P2 = 0x08;
delay(2);
}
}
void T0_time() interrupt 1 //定时器0中断函数
{
TH0 = 0xFA; //重置定时器0初值
TL0 = 0xCD;
DS1302_Init(); //DS1302初始化
}
```
该代码使用了DS1302实时时钟芯片来获取时间。具体的接口和初始化函数在代码中没有给出,需要自行添加。在主函数中,通过计算年份的千位、百位、十位和个位数码管的值来实现万年历的显示效果。在定时器0中断函数中,调用了DS1302的初始化函数来更新时间。
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)