配置MPLS OAM检测PW状态的命令
时间: 2023-11-16 13:06:21 浏览: 58
配置MPLS OAM检测PW(Pseudowire)状态的命令如下:
1. 配置MPLS OAM检测PW状态:
router mpls
mpls oam pseudowire <pw-id> <peer-ip> [vc-id <vc-id>] [interval <interval>] [timeout <timeout>]
其中:
- `<pw-id>`:指定PW的ID。
- `<peer-ip>`:指定远程PE(Provider Edge)的IP地址。
- `<vc-id>`(可选):指定VC(Virtual Circuit)的ID。
- `<interval>`(可选):指定发送OAM报文的间隔时间。
- `<timeout>`(可选):指定超时时间。
2. 配置MPLS OAM检测PW状态的接收端:
router mpls
mpls oam pseudowire <pw-id> receive
其中:
- `<pw-id>`:指定PW的ID。
请注意,上述命令仅提供了一般示例,并且实际的配置可能因设备型号和软件版本而有所不同。确保在配置之前参考厂商文档和设备手册,以获得特定设备的正确命令和语法。
相关问题
mpls oam相关配置命令
在MPLS OAM(Operations, Administration, and Maintenance)方面,以下是一些常用的配置命令:
1. 配置MPLS OAM基础:
router mpls
mpls oam
2. 配置MPLS OAM检测协议:
router mpls
mpls oam bfd
3. 配置MPLS OAM检测接口:
interface <interface>
mpls oam
4. 配置MPLS OAM检测接口的周期性发送间隔:
interface <interface>
mpls oam interval <interval>
5. 配置MPLS OAM检测接口的超时时间:
interface <interface>
mpls oam timeout <timeout>
请注意,上述命令仅提供了一般示例,并且实际的配置可能因设备型号和软件版本而有所不同。确保在配置之前参考厂商文档和设备手册,以获得特定设备的正确命令和语法。
华为交换机MPLS配置命令
以下是华为交换机配置MPLS的基本命令:
1. 开启 MPLS 功能:
```
[MPLS] mpls
```
2. 配置 LSR ID:
```
[MPLS] quit
[~Switch] mpls lsr-id <LSR ID>
```
3. 配置 MPLS 接口:
```
[~Switch] interface <interface-type><interface-number>
[~Switch-<interface-type><interface-number>] mpls enable
```
4. 配置 LDP:
```
[~Switch] mpls ldp
[~Switch-ldp] quit
```
5. 配置 LDP 接口:
```
[~Switch] interface <interface-type><interface-number>
[~Switch-<interface-type><interface-number>] mpls ldp
```
6. 配置 MPLS 静态标签:
```
[~Switch] mpls
[~Switch-mpls] quit
[~Switch] interface <interface-type><interface-number>
[~Switch-<interface-type><interface-number>] mpls
[~Switch-<interface-type><interface-number>-Mpls] quit
[~Switch] mpls
[~Switch-mpls] static-label local <label-value> in <interface-type><interface-number>
```
注意,以上命令仅供参考,具体的配置命令请根据实际情况进行选择和修改。