cpp17的if / switch with Initializer
时间: 2023-05-31 11:03:34 浏览: 65
C++17引入了if语句和switch语句的初始化器。这意味着您可以在if语句和switch语句中声明和初始化变量。这样可以使代码更清晰和简洁,同时避免不必要的变量声明。
if语句的初始化器:
```
if (int i = calculate()) {
// do something with i
}
```
在这个例子中,我们在if语句中声明一个整型变量i,并对其进行初始化。如果calculate()函数返回0,则if语句的条件为false。如果calculate()函数返回非0值,则if语句的条件为true,并且我们可以在if语句块中使用变量i。
switch语句的初始化器:
```
switch (int i = calculate()) {
case 0:
// do something
break;
case 1:
// do something else
break;
default:
// do something by default
break;
}
```
在这个例子中,我们在switch语句中声明一个整型变量i,并对其进行初始化。根据calculate()函数的返回值,我们可以在不同的case中执行不同的操作。如果calculate()函数返回一个不在case中的值,则执行default块中的操作。
相关问题
int main(void) { /* Initialize hardware */ HAL_BOARD_INIT(); // Initialize board I/O InitBoard( OB_COLD ); /* Initialze the HAL driver */ HalDriverInit(); /* Initialize NV system */ osal_snv_init(); /* Initialize LL */ /* Initialize the operating system */ osal_init_system(); /* Enable interrupts */ HAL_ENABLE_INTERRUPTS(); // Final board initialization InitBoard( OB_READY ); #if defined ( POWER_SAVING ) osal_pwrmgr_device( PWRMGR_BATTERY ); #endif /* Start OSAL */ osal_start_system(); // No Return from here return 0; }
这是一段 C 语言程序,它的作用是初始化硬件、驱动和操作系统,并启动操作系统。程序流程如下:
1. 初始化硬件,包括初始化板子的输入输出。
2. 初始化 HAL 驱动。
3. 初始化 NV 系统。
4. 初始化 LL。
5. 初始化操作系统。
6. 启用中断。
7. 完成最后的板子初始化。
8. 开启操作系统。
该程序中的一些函数和宏定义可能是针对特定的硬件平台和操作系统的,因此需要结合具体的开发环境来理解。
#include <Servo.h> Servo myservo; // create servo object to control a servo int switchPin = 2; // switch input pin int servoPin = 9; // servo output pin int switchState = 0; // variable for reading the switch status int servoAngle = 0; // variable for storing the servo angle void setup() { myservo.attach(servoPin); // attaches the servo on pin 9 to the servo object pinMode(switchPin, INPUT); // set the switch pin as input Serial.begin(9600); // initialize serial communication at 9600 bits per second } void loop() { switchState = digitalRead(switchPin); // read the switch state if (switchState == HIGH) { // if the switch is pressed servoAngle = 90; // set the servo angle to 90 degrees myservo.write(servoAngle); // move the servo to the desired angle Serial.println("Switch is on!"); // print a message to the serial monitor } else { // if the switch is not pressed servoAngle = 0; // set the servo angle to 0 degrees myservo.write(servoAngle); // move the servo to the desired angle Serial.println("Switch is off!"); // print a message to the serial monitor } delay(100); // wait for 100 milliseconds }翻译一下这段代码
这段代码是一个基于Arduino的程序,使用了Servo库和一个开关按钮来控制一个舵机的旋转角度。以下是这段代码的翻译:
```
#include <Servo.h> // 引入Servo库
Servo myservo; // 创建一个舵机对象
int switchPin = 2; // 开关输入引脚
int servoPin = 9; // 舵机输出引脚
int switchState = 0; // 读取开关状态的变量
int servoAngle = 0; // 存储舵机角度的变量
void setup() {
myservo.attach(servoPin); // 把舵机引脚9连接到舵机对象
pinMode(switchPin, INPUT); // 把开关引脚设为输入
Serial.begin(9600); // 初始化串口通信,波特率为9600
}
void loop() {
switchState = digitalRead(switchPin); // 读取开关状态
if (switchState == HIGH) { // 如果开关被按下
servoAngle = 90; // 设置舵机角度为90度
myservo.write(servoAngle); // 移动舵机到所需角度
Serial.println("Switch is on!"); // 在串口监视器中打印一条消息
} else { // 如果开关没有被按下
servoAngle = 0; // 设置舵机角度为0度
myservo.write(servoAngle); // 移动舵机到所需角度
Serial.println("Switch is off!"); // 在串口监视器中打印一条消息
}
delay(100); // 延迟100毫秒
}
```