ds18b20程序keil
时间: 2023-05-18 16:01:22 浏览: 132
DS18B20是一款数字温度传感器,适用于各种嵌入式系统和单片机应用。在Keil软件中进行DS18B20程序编写,需要先配置端口和初始化相应的引脚。
首先需要在程序中定义DS18B20的引脚,一般使用单片机的GPIO引脚作为DS18B20的数据引脚,例如P0.0等。然后需要在初始化函数中设置GPIO引脚的模式为输出,以及设置引脚状态为高电平。接着,可以开始进行读取温度的操作。
读取DS18B20的温度分为三个步骤:发送开始转换命令、读取温度数据、进行CRC校验。在开始转换命令中,需要先向DS18B20发送一个复位指令,然后再发送一个开始转换命令。这里需要注意的是,转换命令中包含了DS18B20的分辨率设置,不同分辨率的转换时间不同。
之后,需要进行读取温度数据的操作,读取操作分为上电复位、发送读取命令、读取数据和检查CRC校验四个步骤。最后需要进行CRC校验,确保温度数据的准确性。
总之,在Keil软件中编写DS18B20程序,需要了解DS18B20的工作原理和操作流程,然后根据单片机的引脚定义和GPIO口配置,编写相应的程序代码。同时,在实际应用中需要根据具体情况,对程序进行修改和优化,以达到最佳的性能和稳定性。
相关问题
DS18B20程序设计流程
DS18B20是一种数字温度传感器,以下是DS18B20程序设计的基本流程:
1. 初始化DS18B20传感器:需要设置GPIO引脚的方向和电平状态,以及进行DS18B20特有的初始化过程。
2. 发送指令给DS18B20传感器:发送“读温度”或“写寄存器”等命令,这些命令需要按照一定的时序进行发送。
3. 等待DS18B20传感器响应:在发送完命令后,需要等待DS18B20传感器的响应,以确保传感器已经准备好进行数据传输。
4. 读取DS18B20传感器数据:在准备好的时候,就可以读取DS18B20传感器返回的温度数据,这些数据需要根据DS18B20的协议进行解码和计算。
下面是一个简单的DS18B20程序设计示例,使用STM32F4系列的芯片和Keil MDK进行开发:
```c
#include "stm32f4xx.h"
#include "ds18b20.h"
// 定义DS18B20引脚
#define DS18B20_GPIO_PORT GPIOB
#define DS18B20_GPIO_PIN GPIO_Pin_12
// DS18B20初始化函数
void DS18B20_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// 使能GPIOB时钟
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
// 配置GPIOB.12为输出模式
GPIO_InitStructure.GPIO_Pin = DS18B20_GPIO_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(DS18B20_GPIO_PORT, &GPIO_InitStructure);
}
// 发送DS18B20指令
void DS18B20_SendCommand(uint8_t command)
{
uint8_t i;
// 发送8位数据
for (i = 0; i < 8; i++)
{
// 发送位0或位1
GPIO_SetBits(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN);
if (command & (1 << i))
{
GPIO_ResetBits(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN);
}
// 等待一段时间
Delay_us(50);
// 恢复引脚状态
GPIO_SetBits(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN);
}
}
// 读取DS18B20数据
uint16_t DS18B20_ReadData(void)
{
uint16_t data = 0;
uint8_t i;
// 发送读取温度命令
DS18B20_SendCommand(0xCC); // 跳过ROM指令
DS18B20_SendCommand(0x44); // 温度转换指令
// 等待转换完成
Delay_ms(800);
// 发送读取温度命令
DS18B20_SendCommand(0xCC); // 跳过ROM指令
DS18B20_SendCommand(0xBE); // 读取温度数据指令
// 读取16位数据
for (i = 0; i < 16; i++)
{
// 读取位0或位1
GPIO_SetBits(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN);
if (GPIO_ReadInputDataBit(DS18B20_GPIO_PORT, DS18B20_GPIO_PIN))
{
data |= (1 << i);
}
// 等待一段时间
Delay_us(50);
}
return data;
}
// 计算DS18B20温度
float DS18B20_GetTemperature(uint16_t data)
{
float temperature = 0;
// 将16位数据转换为10位温度数据
if (data & 0x8000)
{
temperature = (float)(~data + 1) * -0.0625;
}
else
{
temperature = (float)data * 0.0625;
}
return temperature;
}
int main(void)
{
float temperature;
// 初始化DS18B20传感器
DS18B20_Init();
while (1)
{
// 读取温度数据
uint16_t data = DS18B20_ReadData();
// 计算温度值
temperature = DS18B20_GetTemperature(data);
// 在串口终端输出温度值
printf("Temperature: %.1f C\r\n", temperature);
// 延时1秒
Delay_ms(1000);
}
}
```
STM32读取DS18B20数据程序
以下是一个基于STM32读取DS18B20温度传感器数据的程序示例,假设使用的是STM32F4系列芯片和Keil C编译器。程序中使用的是GPIO库函数进行GPIO的配置和控制,具体GPIO口和引脚需要根据实际硬件接线情况进行修改。
```c
#include "stm32f4xx.h"
#include <stdio.h>
#define DS18B20_GPIO GPIOA
#define DS18B20_GPIO_PIN GPIO_Pin_0
void Delay(__IO uint32_t nCount) {
while(nCount--) {
}
}
uint8_t DS18B20_Init(void) {
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = DS18B20_GPIO_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(DS18B20_GPIO, &GPIO_InitStructure);
GPIO_SetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0xFF);
GPIO_ResetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x80);
GPIO_SetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0xFF);
if(GPIO_ReadInputDataBit(DS18B20_GPIO, DS18B20_GPIO_PIN) == RESET) {
while(GPIO_ReadInputDataBit(DS18B20_GPIO, DS18B20_GPIO_PIN) == RESET);
return 0;
}
else {
return 1;
}
}
void DS18B20_WriteByte(uint8_t data) {
uint8_t i;
for(i = 0; i < 8; i++) {
GPIO_ResetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x05);
if(data & 0x01) {
GPIO_SetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x80);
}
else {
GPIO_ResetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x80);
}
GPIO_SetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x05);
data >>= 1;
}
}
uint8_t DS18B20_ReadByte(void) {
uint8_t i, data = 0;
for(i = 0; i < 8; i++) {
GPIO_ResetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x05);
GPIO_SetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
Delay(0x05);
if(GPIO_ReadInputDataBit(DS18B20_GPIO, DS18B20_GPIO_PIN)) {
data |= 0x01 << i;
}
Delay(0x60);
GPIO_SetBits(DS18B20_GPIO, DS18B20_GPIO_PIN);
}
return data;
}
void DS18B20_ReadTemp(float *temp) {
uint8_t i, temp_data[2];
int16_t temp_value;
if(DS18B20_Init()) {
DS18B20_WriteByte(0xCC);
DS18B20_WriteByte(0x44);
Delay(0xFF);
DS18B20_Init();
DS18B20_WriteByte(0xCC);
DS18B20_WriteByte(0xBE);
for(i = 0; i < 2; i++) {
temp_data[i] = DS18B20_ReadByte();
}
temp_value = (temp_data[1] << 8) + temp_data[0];
*temp = (float)temp_value / 16.0;
}
}
int main(void) {
float temp;
while(1) {
DS18B20_ReadTemp(&temp);
printf("Temperature: %.1f C\r\n", temp);
Delay(0xFFFFF);
}
}
```
该程序实现了通过DS18B20温度传感器读取温度数据并打印输出,在DS18B20_ReadTemp函数中实现了DS18B20的初始化、写入指令、读取温度值等操作。具体的GPIO口和引脚需要根据实际硬件接线情况进行修改。