基于51单片机用ad采集
时间: 2024-04-23 07:22:26 浏览: 27
基于51单片机进行AD采集的话,一般需要用到外部的ADC芯片,因为51单片机本身不带ADC模块。常用的ADC芯片有很多种,比如常见的MCP3208、ADS1115等。这些芯片具有高精度、低功耗、易于接口、价格低廉等特点,非常适合嵌入式系统中的数据采集应用。
具体实现步骤如下:
1.选择合适的ADC芯片,并按照芯片的接口方式进行连接;
2.编写相应的驱动程序,初始化ADC芯片,并进行数据采集;
3.将采集到的数据进行处理,比如进行滤波、放大、转换等;
4.将处理后的数据传输到上位机或者其他设备进行进一步的处理或者显示。
需要注意的是,ADC芯片的选择和接口方式的设计需要根据具体的应用场景和要求进行选择,还需要考虑到嵌入式系统的资源限制等因素。
相关问题
基于51单片机用ad采集电压,显示在数码管上 代码
好的,这里提供一个简单的基于51单片机用AD采集电压并显示在数码管上的代码示例,供参考:
```
#include <reg52.h>
#include <intrins.h>
#define uint unsigned int
#define uchar unsigned char
sbit DSPORT=P2^2; //数码管数据口
sbit DS1=P0^0; //数码管第一位
sbit DS2=P0^1; //数码管第二位
sbit DS3=P0^2; //数码管第三位
sbit DS4=P0^3; //数码管第四位
sbit CS=P2^1; //ADC芯片片选信号
sbit CLK=P2^0; //ADC芯片时钟信号
sbit DIN=P2^3; //ADC芯片数据输入信号
void delay(uint xms) //延时函数
{
uint i,j;
for(i=xms;i>0;i--)
for(j=110;j>0;j--);
}
uchar code table[] = { //数码管显示表
0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,
0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71
};
void Dsplay(uchar num) //数码管显示函数
{
switch(num)
{
case 1: DSPORT=0; DS1=0; DS2=0; DS3=0; DS4=1; break;
case 2: DSPORT=0; DS1=0; DS2=0; DS3=1; DS4=0; break;
case 3: DSPORT=0; DS1=0; DS2=0; DS3=1; DS4=1; break;
case 4: DSPORT=0; DS1=0; DS2=1; DS3=0; DS4=0; break;
case 5: DSPORT=0; DS1=0; DS2=1; DS3=0; DS4=1; break;
case 6: DSPORT=0; DS1=0; DS2=1; DS3=1; DS4=0; break;
case 7: DSPORT=0; DS1=0; DS2=1; DS3=1; DS4=1; break;
case 8: DSPORT=0; DS1=1; DS2=0; DS3=0; DS4=0; break;
case 9: DSPORT=0; DS1=1; DS2=0; DS3=0; DS4=1; break;
case 10: DSPORT=0; DS1=1; DS2=0; DS3=1; DS4=0; break;
case 11: DSPORT=0; DS1=1; DS2=0; DS3=1; DS4=1; break;
case 12: DSPORT=0; DS1=1; DS2=1; DS3=0; DS4=0; break;
case 13: DSPORT=0; DS1=1; DS2=1; DS3=0; DS4=1; break;
case 14: DSPORT=0; DS1=1; DS2=1; DS3=1; DS4=0; break;
case 15: DSPORT=0; DS1=1; DS2=1; DS3=1; DS4=1; break;
case 16: DSPORT=1; DS1=0; DS2=0; DS3=0; DS4=0; break;
default: break;
}
}
uchar ADConvert() //ADC采集函数
{
uchar i,dat=0;
CS=0;
CLK=0;
DIN=1;
for(i=0;i<8;i++)
{
CLK=0;
_nop_();
dat<<=1;
if(DOUT) dat++;
CLK=1;
_nop_();
}
CS=1;
return dat;
}
void main()
{
uchar num=0;
uint vol=0;
while(1)
{
vol=ADConvert(); //采集电压值
vol=vol*5000/256; //转换为实际电压值,假设ADC参考电压为5V
num=vol/1000; //将电压值拆分成四位数
Dsplay(num+1); //显示千位数
delay(5);
num=(vol%1000)/100;
Dsplay(num+1); //显示百位数
delay(5);
num=(vol%100)/10;
Dsplay(num+1); //显示十位数
delay(5);
num=vol%10;
Dsplay(num+1); //显示个位数
delay(5);
}
}
```
需要注意的是,这段代码仅供参考,具体实现时需要根据自己的硬件实际情况进行修改。同时,需要注意电压转换的精度和参考电压的设置。
嵌入式基于单片机的AD采集程序
下面是基于单片机的AD采集程序,以AT89C51单片机为例。
```c
#include <reg51.h>
sbit ADC_CS = P2^1; //模拟量输入通道选择端口
sbit ADC_CLK = P2^2; //ADC时钟端口
sbit ADC_DIN = P2^3; //模拟量输入端口
sbit ADC_DOUT = P2^4; //ADC数据输出端口
//ADC转换函数
unsigned int ADC_Read(unsigned char ch)
{
unsigned char i;
unsigned int dat = 0;
ADC_CS = 1; //拉高通道选择端口,准备转换
ADC_CLK = 0; //ADC时钟置低
ADC_DIN = 0; //清零模拟量输入端口
//发送起始转换命令
ADC_CS = 0;
ADC_CLK = 0;
ADC_DIN = 1;
ADC_CLK = 1;
ADC_DIN = 1;
ADC_CLK = 0;
//发送通道选择命令
for (i = 0; i < 3; i++)
{
ADC_CLK = 0;
ADC_DIN = ch & 0x80;
ch <<= 1;
ADC_CLK = 1;
}
//接收ADC转换结果
for (i = 0; i < 12; i++)
{
ADC_CLK = 0;
ADC_CLK = 1;
dat <<= 1;
dat |= ADC_DOUT;
}
ADC_CS = 1; //转换完成,拉高通道选择端口
return dat;
}
void main()
{
unsigned int adc_data;
P0 = 0x00; //初始化P0口为输出
P2 = 0xff; //初始化P2口为输入
while (1)
{
P0 = 0x00; //将P0口清零
adc_data = ADC_Read(0); //读取ADC转换结果
P0 = adc_data >> 4; //将ADC转换结果输出到P0口
}
}
```
该代码实现了单通道ADC采样,并将转换结果通过P0口输出。其中,ADC_Read函数用于进行ADC转换,参数ch表示需要采样的模拟量输入通道,返回值为转换结果。在主函数中,首先进行了端口初始化,然后进入循环,不断采样并输出结果。注意,ADC转换过程中需要保证时序的正确性,因此需要仔细按照代码中的时序进行实现。