stm32蜂鸣器高电平触发
时间: 2023-05-27 14:01:49 浏览: 73
要在STM32上使用蜂鸣器高电平触发,您需要使用STM32的GPIO库。以下是一些简单的步骤:
1. 打开所需的GPIO端口(例如,如果您想在PB5上触发蜂鸣器,则需要打开GPIOB端口)。
2. 在初始化函数中将GPIO的模式设置为输出模式,并将输出电平设置为低电平。
3. 在需要触发蜂鸣器的代码中,将GPIO输出电平设置为高电平。
4. 等待您想要触发蜂鸣器的时间。
5. 卸载GPIO输出电平以停止蜂鸣器。
这是一些示例代码:
```
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE); // 打开GPIOB时钟
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5; // 选择PB5引脚
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT; // 设置GPIO模式为输出模式
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz; // 设置输出速率
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOB, &GPIO_InitStructure); // 初始化GPIO
GPIO_SetBits(GPIOB, GPIO_Pin_5); // 将PB5输出电平设置为高电平
Delay(1000); // 等待1秒钟
GPIO_ResetBits(GPIOB, GPIO_Pin_5); // 将PB5输出电平设置为低电平
```
在这个例子中,蜂鸣器连接到了PB5引脚。第3行将GPIO的输出电平设置为低电平,而第11行将输出电平设置为高电平,以触发蜂鸣器。在第13行等待1秒钟后,蜂鸣器停止,在第15行将GPIO的输出电平设置为低电平,停止蜂鸣器。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![docx](https://img-home.csdnimg.cn/images/20210720083331.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)