STM32F103单片机ADC采用TIM1_CC1事件触发代码实现

以下是基于STM32CubeMX和HAL库的代码实现：

1. 配置TIM1和ADC时钟

/* TIM1 clock enable */
__HAL_RCC_TIM1_CLK_ENABLE();

/* ADC1 clock enable */
__HAL_RCC_ADC1_CLK_ENABLE();

2. 配置GPIO引脚和时钟

/* Configure GPIO pin : PA8 */
GPIO_InitStruct.Pin = GPIO_PIN_8;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

/* GPIO Ports Clock Enable */
__HAL_RCC_GPIOA_CLK_ENABLE();

3. 配置TIM1为输入捕获模式，配置ADC为单通道转换模式

/* TIM1 configuration */
htim1.Instance = TIM1;
htim1.Init.Prescaler = 0;
htim1.Init.CounterMode = TIM_COUNTERMODE_UP;
htim1.Init.Period = 65535;
htim1.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
htim1.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
HAL_TIM_IC_Init(&htim1);

/* Configure the Input Capture channel */
sConfig.ICPrescaler = TIM_ICPSC_DIV1;
sConfig.ICFilter = 0;
sConfig.ICPolarity = TIM_ICPOLARITY_RISING;
sConfig.ICSelection = TIM_ICSELECTION_DIRECTTI;
HAL_TIM_IC_ConfigChannel(&htim1, &sConfig, TIM_CHANNEL_1);

/* ADC configuration */
hadc1.Instance = ADC1;
hadc1.Init.ScanConvMode = DISABLE;
hadc1.Init.ContinuousConvMode = DISABLE;
hadc1.Init.DiscontinuousConvMode = DISABLE;
hadc1.Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_T1_CC1;
hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT;
hadc1.Init.NbrOfConversion = 1;
HAL_ADC_Init(&hadc1);

/* Configure Regular Channel */
sConfig.Channel = ADC_CHANNEL_0;
sConfig.Rank = ADC_REGULAR_RANK_1;
sConfig.SamplingTime = ADC_SAMPLETIME_1CYCLE_5;
HAL_ADC_ConfigChannel(&hadc1, &sConfig);

4. 配置TIM1的触发源和开启TIM1和ADC

/* Configure the TIM1 trigger */
sMasterConfig.MasterOutputTrigger = TIM_TRGO_OC1;
sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_ENABLE;
HAL_TIMEx_MasterConfigSynchronization(&htim1, &sMasterConfig);

/* Start TIM1 */
HAL_TIM_IC_Start_IT(&htim1, TIM_CHANNEL_1);

/* Start ADC conversion */
HAL_ADC_Start(&hadc1);

5. 在TIM1的输入捕获中断中进行ADC采样

void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef *htim)
{
    if(htim->Instance == TIM1)
    {
        /* Start ADC conversion */
        HAL_ADC_Start(&hadc1);
    }
}

6. 在ADC转换完成中断中获取采样值

void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc)
{
    /* Get ADC value */
    uint16_t adc_value = HAL_ADC_GetValue(hadc);
    
    /* Do something with the ADC value */
    ...
}

以上是基于STM32CubeMX和HAL库的代码实现，需要根据实际情况进行修改。