esp32 s3 OTG Mass Storage示例
时间: 2023-10-20 20:05:47 浏览: 69
ESP32 S3是一款具有高性能,低功耗和可靠性的芯片。它可以轻松地与其他设备进行通信,并支持各种通信接口,例如UART,SPI,I2C,SDIO等。在本文中,我们将讨论ESP32 S3的OTG Mass Storage示例。
OTG(On-The-Go)是一种通信协议,可以使两个设备直接进行通信,而无需通过主机设备进行通信。在ESP32 S3中,OTG接口支持两种模式:设备模式和主机模式。在设备模式下,ESP32 S3可以作为一个设备连接到另一个主机设备上。在主机模式下,ESP32 S3可以作为主机设备连接到其他设备上。
Mass Storage是一种通信协议,可以将设备作为存储设备连接到计算机或其他设备上。在ESP32 S3中,我们可以使用OTG接口将ESP32 S3作为Mass Storage设备连接到计算机上,以便在计算机上读取和写入ESP32 S3的数据。
下面是ESP32 S3 OTG Mass Storage示例的代码:
```c
#include <Arduino.h>
#include <USBHost_t36.h>
#include <SD.h>
USBHost myusb;
File file;
void setup() {
Serial.begin(115200);
if (!SD.begin(4)) {
Serial.println("SD card initialization failed!");
while (1);
}
Serial.println("SD card initialization done.");
if (myusb.begin()) {
Serial.println("USB Host Shield started.");
} else {
Serial.println("USB Host Shield failed to start.");
while (1);
}
}
void loop() {
USBDevice connected_device = myusb.getConnectedDevice();
if (connected_device.devAddress()) {
Serial.print("Device connected: ");
Serial.println(connected_device.devAddress(), HEX);
Serial.print("Vendor ID: ");
Serial.println(connected_device.idVendor(), HEX);
Serial.print("Product ID: ");
Serial.println(connected_device.idProduct(), HEX);
if (connected_device.idVendor() == 0x0781 && connected_device.idProduct() == 0x5581) { // SanDisk Cruzer Blade
Serial.println("SanDisk Cruzer Blade detected.");
if (myusb.setDeviceConfiguration(connected_device.devAddress(), 1)) {
Serial.println("Device configuration set.");
} else {
Serial.println("Failed to set device configuration.");
}
if (myusb.setDeviceInterface(connected_device.devAddress(), 0, 0)) {
Serial.println("Device interface set.");
} else {
Serial.println("Failed to set device interface.");
}
file = SD.open("/test.txt");
if (file) {
Serial.println("File opened.");
int file_size = file.size();
uint8_t *buf = new uint8_t[file_size];
file.read(buf, file_size);
myusb.write(connected_device.devAddress(), 0x02, 0, buf, file_size);
delete[] buf;
Serial.println("Data written to device.");
file.close();
} else {
Serial.println("Failed to open file.");
}
}
}
delay(1000);
}
```
在上面的示例中,我们使用USBHost库和SD库。首先,我们在setup()函数中初始化SD卡和USB Host Shield。然后,在loop()函数中,我们使用myusb.getConnectedDevice()函数获取连接的设备,并检查它是否为我们所需的SanDisk Cruzer Blade。
如果检测到SanDisk Cruzer Blade,则使用myusb.setDeviceConfiguration()和myusb.setDeviceInterface()函数将设备配置为Mass Storage设备。然后,我们打开SD卡上的test.txt文件,并将其内容读取到一个缓冲区中。最后,我们使用myusb.write()函数将缓冲区中的数据写入连接的设备。
请注意,这只是一个简单的示例。在实际应用中,您可能需要处理更多的设备和文件类型,并且需要更完整的错误处理和调试功能。
相关推荐
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)