ap6212a0_a33_sc3817r_

时间: 2023-05-03 14:03:54 浏览: 119
ap6212a0_a33_sc3817r_是指一款芯片或电路板的型号，通常用于嵌入式系统或智能设备中。其中，ap6212a0是一款Wi-Fi和蓝牙芯片，可以实现无线通信功能；a33是一款低功耗高性能的ARM Cortex-A7处理器，可用于嵌入式系统等场景；而sc3817r是一款具有安全保护机制的移动芯片，支持4G网络以及WCDMA/TD-SCDMA/GSM等多种网络制式。综合这三个部分，ap6212a0_a33_sc3817r_芯片或电路板可以实现无线通信、高性能处理和多种网络制式支持等功能，适用于多种智能设备或嵌入式系统中。
阅读全文

相关推荐

7z

！！！！ap6212a0_a33_sc3817r_验证通过_修正wifi的配置文件为nvram_ap6212.txt

调通sina33下的AP6212A0（WIFI+BT） 大文实验室/大文哥 壹捌陆捌零陆捌捌陆捌贰 wb4916 AT qq.com 完成时间：2017/6/28 12:13 版本：V1.3 本文参照： 《A33 wifi移植说明书.pdf》 还有就是全志R16平台的parrotv1.1的官方SDK（Android4.4.2） 1、打开AP6212的BT，关闭rtl8723bs的BT（其它都是按照比对软件的字母顺序了）： [ 3.141273] Bluetooth: HCI UART driver ver 2.2 [ 3.146210] Bluetooth: HCI H4 protocol initialized [ 3.151563] Bluetooth: HCI BCSP protocol initialized [ 3.157154] usbcore: registered new interface driver btusb [ 3.163282] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 3.169599] Bluetooth: BlueSleep Mode Driver Ver 1.1 [ 3.175402] Bluetooth: get rtl8723bs rtl8723bs_bt_host_wake gpio failed [ 3.953017] Bluetooth: RFCOMM TTY layer initialized [ 3.958456] Bluetooth: RFCOMM socket layer initialized [ 3.964183] Bluetooth: RFCOMM ver 1.11 [ 3.968340] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.968638] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 3.968734] [mmc]: mclk 0xf1c20090 0xc100000b [ 3.989421] Bluetooth: BNEP filters: protocol multicast [ 3.995242] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.001921] L2TP core driver, V2.0 [ 4.005706] PPPoL2TP kernel driver, V2.0 [ 4.010070] L2TP IP encapsulation support (L2TPv3) [ 4.015468] L2TP netlink interface [ 4.019264] L2TP ethernet pseudowire support (L2TPv3) [ 4.023860] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B [ 4.023929] [mmc]: mclk 0xf1c20090 0xc100000b [ 4.040272] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 4.048780] ThumbEE CPU extension supported. [ 4.053550] Registering SWP/SWPB emulation handler [ 4.059269] [rfkill]: rfkill set power 1 [ 4.063652] gpio ap6xxx_bt_regon set val 0, act val 0 正常启动的BT加载： [ 3.207764] Bluetooth: HCI UART driver ver 2.2 [ 3.212725] Bluetooth: HCI H4 protocol initialized [ 3.218045] Bluetooth: HCI BCSP protocol initialized [ 3.223671] us
7z

ap6212a0_a33_sc3817r_神舟验证版本_借用nvram_ap6210这个配置文件_20170626_1834没有外层目录.7z

调通sina33下的AP6212A0（WIFI+BT） 大文实验室/大文哥 壹捌陆捌零陆捌捌陆捌贰 wb4916 AT qq.com 完成时间：2017/6/26 11:01 版本：V1.1 本文参照： 《A33 wifi移植说明书.pdf》 还有就是全志R16的parrotv1.1的官方SDK（Android4.4.2） 1、打开AP6212的BT，关闭rtl8723bs的BT： [ 3.141273] Bluetooth: HCI UART driver ver 2.2 [ 3.146210] Bluetooth: HCI H4 protocol initialized [ 3.151563] Bluetooth: HCI BCSP protocol initialized [ 3.157154] usbcore: registered new interface driver btusb [ 3.163282] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 3.169599] Bluetooth: BlueSleep Mode Driver Ver 1.1 [ 3.175402] Bluetooth: get rtl8723bs rtl8723bs_bt_host_wake gpio failed [ 3.953017] Bluetooth: RFCOMM TTY layer initialized [ 3.958456] Bluetooth: RFCOMM socket layer initialized [ 3.964183] Bluetooth: RFCOMM ver 1.11 [ 3.968340] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.968638] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 3.968734] [mmc]: mclk 0xf1c20090 0xc100000b [ 3.989421] Bluetooth: BNEP filters: protocol multicast [ 3.995242] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.001921] L2TP core driver, V2.0 [ 4.005706] PPPoL2TP kernel driver, V2.0 [ 4.010070] L2TP IP encapsulation support (L2TPv3) [ 4.015468] L2TP netlink interface [ 4.019264] L2TP ethernet pseudowire support (L2TPv3) [ 4.023860] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B [ 4.023929] [mmc]: mclk 0xf1c20090 0xc100000b [ 4.040272] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 4.048780] ThumbEE CPU extension supported. [ 4.053550] Registering SWP/SWPB emulation handler [ 4.059269] [rfkill]: rfkill set power 1 [ 4.063652] gpio ap6xxx_bt_regon set val 0, act val 0 正常启动的BT加载： [ 3.207764] Bluetooth: HCI UART driver ver 2.2 [ 3.212725] Bluetooth: HCI H4 protocol initialized [ 3.218045] Bluetooth: HCI BCSP protocol initialized [ 3.223671] usbcore: registered new interface driver btusb [ 3.229766] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 3.236243] Bluetooth: MSM Sleep Mode Driver Ver 1.2 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r$ ll rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh config Welcome to mkscript setup progress All available chips: 0. sun8iw5p1 Choice: 0 All available platforms: 0. android 1. dragonboard 2. linux Choice: 0 All available kernel: 0. linux-3.4 Choice: 0 All available boards: 0. evb 1. maple 2. redwood 3. y2 4. y3 Choice: 4 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4$ make ARCH=arm menuconfig [*] Networking support ---> <*> Bluetooth subsystem support ---> Bluetooth device drivers ---> < > Broadcom Bluetooth Low Power Manager Support <*> Realtek Bluesleep driver support 修改为： <*> Broadcom Bluetooth Low Power Manager Support < > An inverter between bt hostwake pin and cpu (NEW) < > Realtek Bluesleep driver support 2、（这个不修改：） R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\overlay\frameworks\base\core\res\res\values\config.xml <string-array translatable="false" name="config_tether_wifi_regexs"> <item>"wlan0"</item> </string-array> <string-array translatable="false" name="config_tether_bluetooth_regexs"> <item>"bt-pan"</item> </string-array> 3、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\astar_y3.mk # ap6181/6210/6330 sdio wifi fw and nvram #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6181/device-bcm.mk) #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6210/device-bcm.mk) $(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6212/device-bcm.mk) #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6330/device-bcm.mk) #rtl8723bs bt fw and config #$(call inherit-product, hardware/realtek/bluetooth/rtl8723bs/firmware/rtlbtfw_cfg.mk) # camera config for camera detector #PRODUCT_COPY_FILES += \ # device/softwinner/astar-y3/hawkview/sensor_list_cfg.ini:system/etc/hawkview/sensor_list_cfg.ini #add gms features #PRODUCT_COPY_FILES += \ # frameworks/native/data/etc/android.hardware.faketouch.xml:system/etc/permissions/android.hardware.faketouch.xml \ # frameworks/native/data/etc/android.hardware.touchscreen.multitouch.jazzhand.xml:system/etc/permissions/android.hardware.touchscreen.multitouch.jazzhand.xml \ # frameworks/native/data/etc/android.hardware.usb.host.xml:system/etc/permissions/android.hardware.usb.host.xml # 3G Data Card Packages #PRODUCT_PACKAGES += \ # u3gmonitor \ # chat \ # rild \ # pppd # 3G Data Card Configuration Flie #PRODUCT_COPY_FILES += \ # device/softwinner/polaris-common/rild/ip-down:system/etc/ppp/ip-down \ # device/softwinner/polaris-common/rild/ip-up:system/etc/ppp/ip-up \ # device/softwinner/polaris-common/rild/3g_dongle.cfg:system/etc/3g_dongle.cfg \ # device/softwinner/polaris-common/rild/usb_modeswitch:system/bin/usb_modeswitch \ # device/softwinner/polaris-common/rild/call-pppd:system/xbin/call-pppd \ # device/softwinner/polaris-common/rild/usb_modeswitch.sh:system/xbin/usb_modeswitch.sh \ # device/softwinner/polaris-common/rild/apns-conf_sdk.xml:system/etc/apns-conf.xml \ # device/softwinner/polaris-common/rild/libsoftwinner-ril.so:system/lib/libsoftwinner-ril.so #PRODUCT_COPY_FILES += \ # device/softwinner/polaris-common/rild/init.3gdongle.rc:root/init.sunxi.3gdongle.rc # 3G Data Card usb modeswitch File #PRODUCT_COPY_FILES += \ # $(call find-copy-subdir-files,*,device/softwinner/polaris-common/rild/usb_modeswitch.d,system/etc/usb_modeswitch.d) PRODUCT_PROPERTY_OVERRIDES += \ ro.sw.embeded.telephony = false PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.timezone=Asia/Shanghai \ persist.sys.language=zh \ persist.sys.country=CN PRODUCT_PACKAGES += Bluetooth #PRODUCT_PROPERTY_OVERRIDES += \ # ro.product.8723b_bt.used=true #GPS Feature #PRODUCT_PACKAGES += gps.polaris #BOARD_USES_GPS_TYPE := simulator #PRODUCT_COPY_FILES += frameworks/native/data/etc/android.hardware.location.xml:system/etc/permissions/android.hardware.location.xml # evb logger PRODUCT_COPY_FILES += \ device/softwinner/astar-y3/tools/logger.sh:system/bin/logger.sh PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.usb.config=mass_storage,adb \ ro.adb.secure=0 ro.udisk.lable=Polaris \ ro.font.scale=1.0 \ ro.hwa.force=false \ rw.logger=0 \ ro.sys.bootfast=true \ debug.hwc.showfps=0 \ debug.hwui.render_dirty_regions=false #ro.sys.storage_type = emulated \ #for gms #PRODUCT_PROPERTY_OVERRIDES += \ # ro.sys.mutedrm=true \ # ro.adb.secure=1 PRODUCT_PROPERTY_OVERRIDES += \ ro.sf.lcd_density=213 \ ro.product.firmware=v2.0 $(call inherit-product-if-exists, device/softwinner/astar-y3/modules/modules.mk) DEVICE_PACKAGE_OVERLAYS := device/softwinner/astar-y3/overlay PRODUCT_CHARACTERISTICS := tablet # Overrides PRODUCT_AAPT_CONFIG := xlarge hdpi xhdpi large PRODUCT_AAPT_PREF_CONFIG := xhdpi PRODUCT_BRAND := Allwinner PRODUCT_NAME := astar_y3 PRODUCT_DEVICE := astar-y3 PRODUCT_MODEL := QUAD-CORE A33 y3 PRODUCT_MANUFACTURER := softwinner #include device/softwinner/polaris-common/prebuild/google/products/gms_base.mk 4、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\BoardConfig.mk # wifi and bt configuration # 1. Wifi Configuration # 1.1 realtek wifi support # 1.1 realtek wifi configuration #BOARD_WIFI_VENDOR := realtek ifeq ($(BOARD_WIFI_VENDOR), realtek) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_rtl BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_rtl SW_BOARD_USR_WIFI := rtl8188eu BOARD_WLAN_DEVICE := rtl8188eu #SW_BOARD_USR_WIFI := rtl8723au #BOARD_WLAN_DEVICE := rtl8723au #SW_BOARD_USR_WIFI := rtl8723bs #BOARD_WLAN_DEVICE := rtl8723bs endif # 1.2 broadcom wifi support BOARD_WIFI_VENDOR := broadcom ifeq ($(BOARD_WIFI_VENDOR), broadcom) BOARD_WPA_SUPPLICANT_DRIVER := NL80211 WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_WLAN_DEVICE := bcmdhd WIFI_DRIVER_FW_PATH_PARAM := "/sys/module/bcmdhd/parameters/firmware_path" #SW_BOARD_USR_WIFI := AP6181 #SW_BOARD_USR_WIFI := AP6210 #WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm40181a2.bin" #WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm40181a2_p2p.bin" #WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm40181a2_apsta.bin" # 2017/6/21 15:11 wenyuanbo configure ap6212 use ap6210 SW_BOARD_USR_WIFI := AP6212 WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm43438a0.bin" WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm43438a0_p2p.bin" WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm43438a0_apsta.bin" #SW_BOARD_USR_WIFI := AP6330 #WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm40183b2_ag.bin" #WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm40183b2_ag_p2p.bin" #WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm40183b2_ag_apsta.bin" endif #1.3 eag wifi config #BOARD_WIFI_VENDOR := eagle ifeq ($(BOARD_WIFI_VENDOR), eagle) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_eagle BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_eagle SW_BOARD_USR_WIFI := esp8089 BOARD_WLAN_DEVICE := esp8089 endif # 2. Bluetooth Configuration # make sure BOARD_HAVE_BLUETOOTH is true for every bt vendor BOARD_HAVE_BLUETOOTH := true BOARD_HAVE_BLUETOOTH_BCM := true #SW_BOARD_HAVE_BLUETOOTH_NAME := ap6210 SW_BOARD_HAVE_BLUETOOTH_NAME := ap6212 #SW_BOARD_HAVE_BLUETOOTH_NAME := ap6330 #BOARD_HAVE_BLUETOOTH_RTK := true #BLUETOOTH_HCI_USE_RTK_H5 := true #SW_BOARD_HAVE_BLUETOOTH_NAME := rtl8723bs 5、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\init.sun8i.rc on early-fs mount_all /fstab.sun8i setprop ro.crypto.fuse_sdcard true insmod /system/vendor/modules/disp.ko insmod /system/vendor/modules/lcd.ko insmod /system/vendor/modules/mali.ko insmod /system/vendor/modules/leds-sunxi.ko insmod /system/vendor/modules/bcmdhd.ko insmod /system/vendor/modules/bcm_btlpm.ko #2G or 3G init.rc # import init.sunxi.3gdongle.rc ## 1. realtek & eagle wifi service ## 1.1 realtek & eagle wifi sta service #service wpa_supplicant /system/bin/wpa_supplicant \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -O/data/misc/wifi/sockets \ # -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # # we will start as root and wpa_supplicant will switch to user wifi # # after setting up the capabilities required for WEXT # # user wifi # # group wifi inet keystore # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # ## 1.2 realtek & eagle wifi sta p2p concurrent service #service p2p_supplicant /system/bin/wpa_supplicant \ # -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ # -e/data/misc/wifi/entropy.bin -N \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -O/data/misc/wifi/sockets \ # -g@android:wpa_wlan0 # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # 2. broadcom wifi service # 2.1 broadcom wifi station and softap service wpa_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -I/system/etc/wifi/wpa_supplicant_overlay.conf \ -O/data/misc/wifi/sockets \ -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot # 2.2 broadcom wifi sta p2p concurrent service service p2p_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -I/system/etc/wifi/wpa_supplicant_overlay.conf \ -O/data/misc/wifi/sockets -N \ -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ -I/system/etc/wifi/p2p_supplicant_overlay.conf \ -puse_p2p_group_interface=1 -e/data/misc/wifi/entropy.bin \ -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot 6、（不需要修改） R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\ueventd.sun8i.rc 7、 R:\wyb\ap6212a0_a33_sc3817r\android\frameworks\base\packages\SettingsProvider\res\values\defaults.xml <integer name="def_screen_off_timeout">1800000</integer> <bool name="def_lockscreen_disabled">true</bool> 8、 R:\wyb\ap6212a0_a33_sc3817r\android\frameworks\base\services\java\com\android\server\BatteryService.java // private static final boolean DEBUG = false; private static final boolean DEBUG = true; private void sendIntentLocked() { // Pack up the values and broadcast them to everyone final Intent intent = new Intent(Intent.ACTION_BATTERY_CHANGED); intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY | Intent.FLAG_RECEIVER_REPLACE_PENDING); int icon = getIconLocked(mBatteryProps.batteryLevel); intent.putExtra(BatteryManager.EXTRA_STATUS, mBatteryProps.batteryStatus); intent.putExtra(BatteryManager.EXTRA_HEALTH, mBatteryProps.batteryHealth); intent.putExtra(BatteryManager.EXTRA_PRESENT, mBatteryProps.batteryPresent); //intent.putExtra(BatteryManager.EXTRA_LEVEL, mBatteryProps.batteryLevel); intent.putExtra(BatteryManager.EXTRA_LEVEL, 100); intent.putExtra(BatteryManager.EXTRA_SCALE, BATTERY_SCALE); intent.putExtra(BatteryManager.EXTRA_ICON_SMALL, icon); intent.putExtra(BatteryManager.EXTRA_PLUGGED, mPlugType); //intent.putExtra(BatteryManager.EXTRA_VOLTAGE, mBatteryProps.batteryVoltage); intent.putExtra(BatteryManager.EXTRA_VOLTAGE, 4200); intent.putExtra(BatteryManager.EXTRA_TEMPERATURE, mBatteryProps.batteryTemperature); intent.putExtra(BatteryManager.EXTRA_TECHNOLOGY, mBatteryProps.batteryTechnology); intent.putExtra(BatteryManager.EXTRA_INVALID_CHARGER, mInvalidCharger); if (DEBUG) { Slog.d(TAG, "2016/12/05 10:41 wenyuanbo **** Sending ACTION_BATTERY_CHANGED. level:" + mBatteryProps.batteryLevel + ", scale:" + BATTERY_SCALE + ", status:" + mBatteryProps.batteryStatus + ", health:" + mBatteryProps.batteryHealth + ", present:" + mBatteryProps.batteryPresent + ", voltage: " + mBatteryProps.batteryVoltage + ", temperature: " + mBatteryProps.batteryTemperature + ", technology: " + mBatteryProps.batteryTechnology + ", AC powered:" + mBatteryProps.chargerAcOnline + ", USB powered:" + mBatteryProps.chargerUsbOnline + ", Wireless powered:" + mBatteryProps.chargerWirelessOnline + ", icon:" + icon + ", invalid charger:" + mInvalidCharger); } mHandler.post(new Runnable() { @Override public void run() { ActivityManagerNative.broadcastStickyIntent(intent, null, UserHandle.USER_ALL); } }); } 9、（直接拷贝同目录下的ap6210：） R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\conf\softwinner\ap6212\Android.mk LOCAL_PATH := $(call my-dir) include $(CLEAR_VARS) LOCAL_MODULE := bt_vendor.conf LOCAL_MODULE_CLASS := ETC LOCAL_MODULE_PATH := $(TARGET_OUT)/etc/bluetooth LOCAL_MODULE_TAGS := eng LOCAL_SRC_FILES := $(LOCAL_MODULE) include $(BUILD_PREBUILT) R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\conf\softwinner\ap6212\bt_vendor.conf # UART device port where Bluetooth controller is attached UartPort = /dev/ttyS1 # Firmware patch file location FwPatchFilePath = /system/vendor/modules/ # Firmware Name FwPatchFileName = bcm43438a0.hcd 10、新增：vnd_astar-y3-ap6212.txt，直接拷贝：vnd_astar-y2-ap6210.txt R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\include\vnd_astar-y3-ap6212.txt R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\include\vnd_astar-y2-ap6210.txt BLUETOOTH_UART_DEVICE_PORT = "/dev/ttyS1" FW_PATCHFILE_LOCATION = "/system/vendor/modules/" LPM_IDLE_TIMEOUT_MULTIPLE = 5 UART_TARGET_BAUD_RATE = 1500000 BT_WAKE_VIA_PROC = TRUE #LPM_SLEEP_MODE = FALSE BTVND_DBG = TRUE BTHW_DBG = TRUE VNDUSERIAL_DBG = TRUE UPIO_DBG = TRUE 11、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\src\userial_vendor.c //#ifdef USE_AP6210_BT_MODULE #if defined(USE_AP6210_BT_MODULE) || defined(USE_AP6212_BT_MODULE) /* PATCH for AP6210. Will detect CTS(module side) to select transport mode*/ ALOGE("userial vendor open: USE AP6210 BT MODULE."); usleep(100000); close(vnd_userial.fd); if ((vnd_userial.fd = open(vnd_userial.port_name, O_RDWR)) == -1) { ALOGE("userial vendor open: unable to open %s", vnd_userial.port_name); return -1; } #endif //USE_AP6210_BT_MODULE 12、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\Android.mk ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) LOCAL_CFLAGS += -DUSE_AP6210_BT_MODULE endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) LOCAL_CFLAGS += -DUSE_AP6212_BT_MODULE endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6330) include $(LOCAL_PATH)/conf/softwinner/ap6330/Android.mk endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) include $(LOCAL_PATH)/conf/softwinner/ap6210/Android.mk endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) include $(LOCAL_PATH)/conf/softwinner/ap6212/Android.mk endif 13、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\vnd_buildcfg.mk ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) SRC := $(call my-dir)/include/$(addprefix vnd_, $(addsuffix -ap6210.txt,$(basename $(TARGET_DEVICE)))) endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) SRC := $(call my-dir)/include/$(addprefix vnd_, $(addsuffix -ap6212.txt,$(basename $(TARGET_DEVICE)))) endif 14、（这些AP6212的WIFI的bin文件和BT的hcd文件来自全志R16的SDK，当然也可以找正基原厂/代理商索取：） R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\bcm43438a0.hcd （根据ap6210修改：） R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\device-bcm.mk # # Copyright (C) 2008 The Android Open Source Project # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # ######################## -include hardware/broadcom/wlan/bcmdhd/config/config-bcm.mk PRODUCT_COPY_FILES += \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0.bin:system/vendor/modules/fw_bcm43438a0.bin \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0_apsta.bin:system/vendor/modules/fw_bcm43438a0_apsta.bin \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0_p2p.bin:system/vendor/modules/fw_bcm43438a0_p2p.bin \ hardware/broadcom/wlan/firmware/ap6212/nvram_ap6210.txt:system/vendor/modules/nvram_ap6210.txt \ hardware/broadcom/wlan/firmware/ap6212/bcm43438a0.hcd:system/vendor/modules/bcm43438a0.hcd #hardware/broadcom/wlan/firmware/ap6212/config.txt:system/vendor/modules/config.txt ######################## R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0_apsta.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0_p2p.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\nvram_ap6212.txt 直接拷贝自nvram_ap6212.txt： R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\nvram_ap6210.txt 15、（可选修改：） R:\wyb\ap6212a0_a33_sc3817r\android\packages\apps\Camera2\src\com\android\camera\CameraActivity.java private BroadcastReceiver mBatteryInfoReceiver = new BroadcastReceiver() { @Override public void onReceive(Context context, Intent intent) { String action = intent.getAction(); if (Intent.ACTION_BATTERY_CHANGED.equals(action)) { int Level = intent.getIntExtra("level", 0); int Scale = intent.getIntExtra("scale", 100); Log.w(TAG, "2016/11/29 19:54 &&&& wenyuanbo battery Level" + Level); /* *Logic: *1.the battery level is lower then 5%. *2.if in camera, make sure that not in the snapshot progress. *3.if in videocamera, make sure that not in the videorecording progress. *4.everytime starting the camera activity, the battery level is broadcasted, * if meeting the conditions above, give a dialog, press it and finish the activity. *5.if the conditions are not satisfied when started, play for a moment, in the camera acitvity * or video camera activity, the conditiosn are satisfied, also give a dialog for finishing the activity. * *by fuqiang. */ if(Level < 5) { Runnable runnable_close_camera = new Runnable() { @Override public void run() { //close the camera. // CameraActivity.this.finish(); } }; Log.w(TAG, "2016/11/29 18:20 **** wenyuanbo battery Level" + Level); showLocationDialog(); } /* *Logic: *1.the battery level is lhigher then 5% and lower than 15%. *2.if in camera, make sure that not in the snapshot progress. *3.if in videocamera, make sure that not in the videorecording progress. *4.whether in camera or in videocamera, make sure that the flash mode is supported. *5.everytime starting the camera activity, the battery level is broadcasted, * if meeting the conditions above, forbidden the flash(gray icon), give a dialog to notise user. *6.if the conditions are not satisfied when started, play for a moment, in the camera acitvity * or video camera activity, the conditiosn are satisfied, forbidden the flash and give a notice dialog. *7.the dialog is only given once for each camera activity starting. * *by fuqiang. */ else if(Level < 16) { //close the flash mode. /* if (mIsLowBatteryDialogShown == false) { mRotateDialog.showAlertDialog( getString(R.string.warning), getString(R.string.low_battery_15), null, null, getString(R.string.close), null); mIsLowBatteryDialogShown = true; } */ } } } }; 16、（可选：） R:\wyb\ap6212a0_a33_sc3817r\lichee\tools\pack\chips\sun8iw5p1\configs\default\env.cfg bootdelay=3 loglevel=8 17、 R:\wyb\ap6212a0_a33_sc3817r\lichee\tools\pack\chips\sun8iw5p1\configs\y3\sys_config.fex [power_sply] dcdc1_vol = 3000 dcdc2_vol = 1100 dcdc3_vol = 1200 dcdc4_vol = 0 dcdc5_vol = 1500 aldo1_vol = 3300 aldo2_vol = 2500 aldo3_vol = 3000 dldo1_vol = 3300 dldo2_vol = 3300 dldo3_vol = 2800 ;gpio0_vol = 2800 ldoio0_vol = 2800 ;---------------------------------------------------------------------------------- ;uart configuration ;uart_used = uart x enable ;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function ;---------------------------------------------------------------------------------- [uart0] uart_used = 1 uart_port = 0 uart_type = 2 uart_tx = port:PF02<3><1><default><default> uart_rx = port:PF04<3><1><default><default> [uart1] uart_used = 1 uart_port = 1 uart_type = 4 uart_tx = port:PG06<2><1><default><default> uart_rx = port:PG07<2><1><default><default> uart_rts = port:PG08<2><1><default><default> uart_cts = port:PG09<2><1><default><default> [uart2] uart_used = 1 uart_type = 4 uart_tx = port:PB00<2><1><default><default> uart_rx = port:PB01<2><1><default><default> uart_rts = port:PB02<2><1><default><default> uart_cts = port:PB03<2><1><default><default> [uart3] uart_used = 0 uart_type = 4 uart_tx = port:PH06<3><1><default><default> uart_rx = port:PH07<3><1><default><default> uart_rts = port:PH08<3><1><default><default> uart_cts = port:PH09<3><1><default><default> [uart4] uart_used = 0 uart_port = 4 uart_type = 2 uart_tx = port:PA04<2><1><default><default> uart_rx = port:PA05<2><1><default><default> uart_rts = port:PA06<2><1><default><default> uart_cts = port:PA07<2><1><default><default> ;---------------------------------------------------------------------------------- ;capacitor tp configuration ;ctp_twi_id : twi controller ID ;ctp_twi_addr : I2C slave address, 7bit ;ctp_screen_max_x/_y : resolution of touch panel ;ctp_revert_x/_y_flag : whether need to revert x/y ;ctp_exchange_x_y_flag: whether need to exchange the value of x and y ;ctp_int_port : port for tp's interrupt signal ;ctp_wakeup : port for wakeup tp ;---------------------------------------------------------------------------------- [ctp_para] ctp_used = 1 ctp_name = "gt82x" ctp_twi_id = 0 ctp_twi_addr = 0x5d ctp_screen_max_x = 1280 ctp_screen_max_y = 800 ctp_revert_x_flag = 1 ctp_revert_y_flag = 1 ctp_exchange_x_y_flag = 1 ctp_int_port = port:PL04<4><default><default><default> ctp_wakeup = port:PL03<1><default><default><1> ctp_power_ldo = ctp_power_ldo_vol = ctp_power_io = ;-------------------------------------------------------------------------------- ; CTP automatic detection configuration ;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused ;Module name postposition 1 said detection, 0 means no detection. ;-------------------------------------------------------------------------------- [ctp_list_para] ctp_det_used = 1 ft5x_ts = 1 gt82x = 1 gslX680 = 1 gslX680new = 0 gt9xx_ts = 1 gt9xxf_ts = 0 tu_ts = 0 gt818_ts = 1 zet622x = 1 aw5306_ts = 1 icn83xx_ts = 0 [lcd0_para] lcd_used = 1 lcd_driver_name = "default_lcd" lcd_if = 3 lcd_x = 1280 lcd_y = 800 lcd_width = 150 lcd_height = 94 lcd_dclk_freq = 71 lcd_pwm_used = 1 lcd_pwm_ch = 0 lcd_pwm_freq = 50000 lcd_pwm_pol = 1 lcd_hbp = 20 lcd_ht = 1418 lcd_hspw = 10 lcd_vbp = 10 lcd_vt = 830 lcd_vspw = 5 lcd_lvds_if = 0 lcd_lvds_colordepth = 1 lcd_lvds_mode = 0 lcd_frm = 1 lcd_gamma_en = 0 lcd_bright_curve_en = 0 lcd_cmap_en = 0 deu_mode = 0 lcdgamma4iep = 22 smart_color = 90 lcd_bl_en = port:PD13<1><0><default><1> ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;lcd_bl_en = port:PL06<1><0><default><1> lcd_power = "axp22_dc1sw" lcdd0 = port:PD18<3><0><default><default> lcdd1 = port:PD19<3><0><default><default> lcdd2 = port:PD20<3><0><default><default> lcdd3 = port:PD21<3><0><default><default> lcdd4 = port:PD22<3><0><default><default> lcdd5 = port:PD23<3><0><default><default> lcdd6 = port:PD24<3><0><default><default> lcdd7 = port:PD25<3><0><default><default> lcdd8 = port:PD26<3><0><default><default> lcdd9 = port:PD27<3><0><default><default> ;---------------------------------------------------------------------------------- ;pwm config ;---------------------------------------------------------------------------------- [pwm0_para] pwm_used = 0 pwm_positive = port:PH00<2><0><default><default> [pwm1_para] pwm_used = 1 pwm_positive = port:PH01<2><0><default><default> ;-------------------------------------------------------------------------------- ;wifi configuration ;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3 ;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2 ;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0) ;wifi_mod_sel: 0- none, 1- ap6181, 2- ap6210(wifi+bt), ; 3 - rtl8188eu, 4- rtl8723au(wifi+bt), ; 5 - rtl8723bs, 6- esp8089 ;-------------------------------------------------------------------------------- [wifi_para] wifi_used = 1 wifi_sdc_id = 1 wifi_usbc_id = 1 wifi_usbc_type = 1 wifi_mod_sel = 2 wifi_power = "axp22_dldo1" wifi_power_ext1 = "axp22_dldo2" wifi_power_ext2 = "axp22_aldo1" wifi_power_switch = ;wifi_power_switch = port:power0<1><0><default><0> ; 1 - ap6181 sdio wifi gpio config ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ;ap6xxx_lpo_use_apclk = 1 ; 2 - ap6210 sdio wifi gpio config ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_regon = port:PD13<1><default><default><0> ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ap6xxx_bt_regon = port:PL08<1><default><default><0> ap6xxx_bt_wake = port:PL10<1><default><default><0> ap6xxx_bt_host_wake = port:PL09<4><default><default><0> ap6xxx_lpo_use_apclk = 1 ; 3 - rtl8188eu usb wifi gpio conifg ; 4 - rtl8723au usb wifi + bt ; 5 - rtl8723bs sdio wifi + bt ;rtl8723bs_chip_en = port:PL11<1><default><default><0> ;rtl8723bs_wl_regon = port:PL06<1><default><default><0> ;rtl8723bs_wl_host_wake = port:PL07<4><default><default><0> ;rtl8723bs_bt_regon = port:PL08<1><default><default><0> ;rtl8723bs_bt_wake = port:PL10<1><default><default><0> ;rtl8723bs_bt_host_wake = port:PL09<4><default><default><0> ;rtl8723bs_lpo_use_apclk = 0 ; 6 - eagle sdio wifi ;esp_wl_chip_en = port:PL03<1><default><default><0> ;esp_wl_rst = port:PL02<1><default><default><0> ;-------------------------------------------------------------------------------- ;blue tooth ;bt_used ---- blue tooth used (0- no used, 1- used) ;bt_uard_id ---- uart index ;-------------------------------------------------------------------------------- [bt_para] bt_used = 1 bt_uart_id = 1 power_start = 3 pmu_temp_enable = 0 18、 刷机之后，BT可以用。 传输4.5MB的JPG图片大概需要2分钟。 WIFI： 在设置→WLAN（打开之后）： shell@astar-y3:/ $ shell@astar-y3:/ $ [ 469.609956] init: computing context for service '/system/bin/wpa_supplicant' [ 469.618386] init: starting 'p2p_supplicant' [ 469.625739] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 469.673379] init: waitpid returned pid 2065, status = 0000ff00 [ 469.679923] init: process 'p2p_supplicant', pid 2065 exited [ 476.197334] sndpcm_unmute,line:1099 [ 451.464755] CPU1: Booted secondary processor [ 478.459403] CPU1: shutdown [ 478.462947] [hotplug]: cpu(0) try to kill cpu(1) [ 478.468478] [hotplug]: cpu1 is killed! . shell@astar-y3:/ $ 分析启动的log： [ 17.526849] gpio ap6xxx_wl_regon set val 1, act val 1 [ 17.632508] [ap6xxx]: sdio wifi power state: on [ 17.637576] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.637751] =========== WLAN placed in POWER ON ======== [ 17.654651] [mmc]: sdc1 card_power_on start... [ 17.659576] [mmc]: sdc1 power_supply is null [ 17.664322] [mmc]: sdc1 card_power_on ok [ 17.680039] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.690275] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.772361] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 17.781309] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 17.789448] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.799714] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.862032] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.872262] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.933953] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 8, RTO !! [ 17.941997] *******************Try sdio******************* [ 17.948400] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.958630] [mmc]: mclk 0xf1c2008c 0x8002000e [ 18.027775] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 18.035416] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 18.043087] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 18.051920] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 18.145287] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 18.155436] [mmc]: mclk 0xf1c2008c 0x8002000e [ 18.215346] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 18.225736] [mmc]: mclk 0xf1c2008c 0x8100000b [ 18.285675] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 18.296021] [mmc]: mclk 0xf1c2008c 0x8140030b [ 18.357915] mmc1: new high speed SDIO card at address 0001 [ 18.364532] bcmsdh_register: Linux Kernel SDIO/MMC Driver [ 18.364575] *******************sdio init ok******************* [ 18.377207] bcm_wlan_get_oob_irq enter. [ 18.381537] gpio [359] map to virq [7] ok [ 18.388851] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4 [ 18.396019] dhdsdio_probe_attach: unsupported chip: 0xa9a6 [ 18.402155] dhdsdio_probe: dhdsdio_probe_attach failed [ 18.407899] bcmsdh_probe: device attach failed [ 18.412981] [ 18.412984] Dongle Host Driver, version 1.88.45.3 (r420671) [ 18.412989] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 12:06:39 [ 18.428835] dhd_module_init: sdio_register_driver timeout or error [ 18.435928] gpio ap6xxx_wl_regon set val 0, act val 0 [ 18.541549] [ap6xxx]: sdio wifi power state: off [ 18.546679] =========== WLAN placed in POWER OFF ======== [ 18.546915] mmc1: card 0001 removed [ 18.546995] [mmc]: mmc not poweroff notifiy [ 18.547007] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 18.547160] [mmc]: sdc1 card_power_off start... [ 18.547166] [mmc]: sdc1 power_supply is null [ 18.547173] [mmc]: sdc1 card_power_off ok [ 18.631655] init: command 'insmod' r=-1 [ 18.636066] init: command 'insmod' r=-1 [ 18.658010] fs_mgr: swapon failed for /dev/block/zram0 [ 18.663804] init: command 'swapon_all' r=-1 [ 18.668504] init: processing action 0x58e70 (console_init) [ 18.675396] init: width = 1280 [ 18.678788] init: height = 800 [ 18.682224] init: s.st_size = 3145728 [ 18.686308] init: logo match failed!fbsize = 4096000 [ 18.718811] init: command 'console_init' r=0 [ 18.723628] init: processing action 0x55bf0 (fs) [ 18.730640] init: command 'mkdir' r=-2 [ 18.741901] init: command 'insmod' r=0 [ 18.752227] init: command 'insmod' r=0 [ 18.756491] init: command 'insmod' r=-1 [ 18.771211] init: command 'insmod' r=0 [ 18.779731] init: command 'insmod' r=0 [ 18.791739] init: command 'insmod' r=0 [ 18.803941] init: command 'insmod' r=0 [ 18.816178] init: command 'insmod' r=0 19、查找：（dhdsdio_probe_attach: unsupported chip: 0xa9a6） rootroot@rootroot-E400:~$ cd wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "unsupported chip" . -R ./dhd_sdio.c: DHD_ERROR(("%s: unsupported chip: 0xx\n", ./sbutils.c: SI_ERROR(("sb_chip2numcores: unsupported chip 0x%x\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko 匹配到二进制文件 ./sbutils.o rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ 经过确认： R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd\dhd_sdio.c static bool dhdsdio_probe_attach(struct dhd_bus *bus, osl_t *osh, void *sdh, void *regsva, uint16 devid) { …… bcmsdh_chipinfo(sdh, bus->sih->chip, bus->sih->chiprev); if (!dhdsdio_chipmatch((uint16)bus->sih->chip)) { DHD_ERROR(("%s: unsupported chip: 0xx\n", __FUNCTION__, bus->sih->chip)); goto fail; } …… } 继续追踪： static bool dhdsdio_chipmatch(uint16 chipid) { if (chipid == BCM4325_CHIP_ID) return TRUE; if (chipid == BCM4329_CHIP_ID) return TRUE; if (chipid == BCM4315_CHIP_ID) return TRUE; if (chipid == BCM4319_CHIP_ID) return TRUE; if (chipid == BCM4336_CHIP_ID) return TRUE; if (chipid == BCM4330_CHIP_ID) return TRUE; if (chipid == BCM43237_CHIP_ID) return TRUE; if (chipid == BCM43362_CHIP_ID) return TRUE; if (chipid == BCM4314_CHIP_ID) return TRUE; if (chipid == BCM43242_CHIP_ID) return TRUE; if (chipid == BCM43340_CHIP_ID) return TRUE; if (chipid == BCM43341_CHIP_ID) return TRUE; if (chipid == BCM43143_CHIP_ID) return TRUE; if (chipid == BCM43342_CHIP_ID) return TRUE; if (chipid == BCM4334_CHIP_ID) return TRUE; if (chipid == BCM43239_CHIP_ID) return TRUE; if (chipid == BCM4324_CHIP_ID) return TRUE; if (chipid == BCM4335_CHIP_ID) return TRUE; if (chipid == BCM4339_CHIP_ID) return TRUE; if (chipid == BCM43349_CHIP_ID) return TRUE; if (chipid == BCM4345_CHIP_ID) return TRUE; if (chipid == BCM4350_CHIP_ID) return TRUE; if (chipid == BCM4354_CHIP_ID) return TRUE; if (chipid == BCM4356_CHIP_ID) return TRUE; if (chipid == BCM4358_CHIP_ID) return TRUE; if (chipid == BCM4371_CHIP_ID) return TRUE; if (chipid == BCM43430_CHIP_ID) return TRUE; if (BCM4349_CHIP(chipid)) return TRUE; return FALSE; } 20、 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ll 总用量 40 drwxr-xr-x 7 rootroot rootroot 4096 6月 26 12:02 ./ drwx------ 6 rootroot rootroot 4096 6月 26 14:16 ../ drwxr-xr-x 10 rootroot rootroot 4096 9月 4 2014 brandy/ -rw-rw-r-- 1 rootroot rootroot 116 6月 26 12:02 .buildconfig drwxr-xr-x 15 rootroot rootroot 4096 9月 4 2014 buildroot/ -r-xr-xr-x 1 rootroot rootroot 55 9月 4 2014 build.sh* drwxr-xr-x 28 rootroot rootroot 4096 6月 26 14:30 linux-3.4/ drwxrwxr-x 3 rootroot rootroot 4096 6月 26 12:02 out/ -r--r--r-- 1 rootroot rootroot 232 9月 4 2014 README drwxr-xr-x 7 rootroot rootroot 4096 6月 7 19:33 tools/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh config Welcome to mkscript setup progress All available chips: 0. sun8iw5p1 Choice: 0 All available platforms: 0. android 1. dragonboard 2. linux Choice: 0 All available kernel: 0. linux-3.4 Choice: 0 All available boards: 0. evb 1. maple 2. redwood 3. y2 4. y3 Choice: 4 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh INFO: ---------------------------------------- INFO: build lichee ... INFO: chip: sun8iw5p1 INFO: platform: android INFO: kernel: linux-3.4 INFO: board: y3 INFO: output: out/sun8iw5p1/android/y3 INFO: ---------------------------------------- INFO: build buildroot ... external toolchain has been installed INFO: build buildroot OK. INFO: build kernel ... INFO: prepare toolchain ... Building kernel CHK include/linux/version.h CHK include/generated/utsrelease.h make[1]: “include/generated/mach-types.h”是最新的。 CALL scripts/checksyscalls.sh CHK include/generated/compile.h CC arch/arm/mach-sunxi/pm/standby/common.o CC arch/arm/mach-sunxi/pm/standby/standby_clock.o CC arch/arm/mach-sunxi/pm/standby/standby_ir.o CC arch/arm/mach-sunxi/pm/standby/standby_key.o CC arch/arm/mach-sunxi/pm/standby/standby_power.o CC arch/arm/mach-sunxi/pm/standby/standby_twi.o CC arch/arm/mach-sunxi/pm/standby/standby_usb.o AS arch/arm/mach-sunxi/pm/standby/standby_delay.o CC arch/arm/mach-sunxi/pm/standby/./arisc/standby_arisc.o CC arch/arm/mach-sunxi/pm/standby/./arisc/arisc_hwmsgbox.o CHK kernel/config_data.h CC arch/arm/mach-sunxi/pm/standby/./arisc/arisc_hwspinlock.o CC arch/arm/mach-sunxi/pm/standby/./arisc/arisc_message_manager.o CC arch/arm/mach-sunxi/pm/standby/./../pm_debug.o CC arch/arm/mach-sunxi/pm/standby/./../mem_timing.o CC arch/arm/mach-sunxi/pm/standby/./../mem_mmu_pc.o AS arch/arm/mach-sunxi/pm/standby/./../mem_mmu_pc_asm.o CC arch/arm/mach-sunxi/pm/standby/./../mem_serial.o CC arch/arm/mach-sunxi/pm/standby/./../mem_printk.o AS arch/arm/mach-sunxi/pm/standby/./../mem_divlib.o CC arch/arm/mach-sunxi/pm/standby/./../mem_divlibc.o CC arch/arm/mach-sunxi/pm/standby/./../mem_int.o CC arch/arm/mach-sunxi/pm/standby/./../mem_tmr.o CC arch/arm/mach-sunxi/pm/standby/./../mem_tmstmp.o CC arch/arm/mach-sunxi/pm/standby/./../mem_clk.o CC arch/arm/mach-sunxi/pm/standby/./../mem_hwspinlock.o CC arch/arm/mach-sunxi/pm/standby/standby.o rm -rf *.o arch/arm/mach-sunxi/pm/standby/../*.o CC arch/arm/mach-sunxi/pm/standby/super/common.o CC arch/arm/mach-sunxi/pm/standby/super/super_twi.o CC [M] drivers/net/wireless/bcmdhd/dhd_sdio.o AS arch/arm/mach-sunxi/pm/standby/super/super_delay.o CC arch/arm/mach-sunxi/pm/standby/super/super_clock.o CC arch/arm/mach-sunxi/pm/standby/super/super_power.o CC arch/arm/mach-sunxi/pm/standby/super/super_cpus.o AS arch/arm/mach-sunxi/pm/standby/super/resume/resume1.o CC arch/arm/mach-sunxi/pm/standby/super/resume/resume_head.o CC arch/arm/mach-sunxi/pm/standby/super/resume/resume1_c_part.o CC arch/arm/mach-sunxi/pm/standby/../pm_debug.o CC arch/arm/mach-sunxi/pm/standby/../mem_timing.o CC arch/arm/mach-sunxi/pm/standby/../mem_mmu_pc.o AS arch/arm/mach-sunxi/pm/standby/../mem_mmu_pc_asm.o CC arch/arm/mach-sunxi/pm/standby/../mem_cpu.o CC arch/arm/mach-sunxi/pm/standby/../mem_serial.o CC arch/arm/mach-sunxi/pm/standby/../mem_printk.o CC [M] drivers/net/wireless/bcmdhd/dhd_cdc.o CC [M] drivers/net/wireless/bcmdhd/bcmsdh_linux.o CC [M] drivers/net/wireless/bcmdhd/dhd_common.o AS arch/arm/mach-sunxi/pm/standby/../mem_divlib.o CC arch/arm/mach-sunxi/pm/standby/../mem_divlibc.o drivers/net/wireless/bcmdhd/dhd_sdio.c: In function ‘dhdsdio_chipmatch’: drivers/net/wireless/bcmdhd/dhd_sdio.c:6936:16: error: ‘BCM43430_CHIP_ID’ undeclared (first use in this function) drivers/net/wireless/bcmdhd/dhd_sdio.c:6936:16: note: each undeclared identifier is reported only once for each function it appears in CC arch/arm/mach-sunxi/pm/standby/../mem_int.o make[4]: *** [drivers/net/wireless/bcmdhd/dhd_sdio.o] 错误 1 make[4]: *** 正在等待未完成的任务.... CC arch/arm/mach-sunxi/pm/standby/../mem_tmr.o CC arch/arm/mach-sunxi/pm/standby/../mem_tmstmp.o CC arch/arm/mach-sunxi/pm/standby/../mem_hwspinlock.o CC arch/arm/mach-sunxi/pm/standby/../mem_clk.o Source file is open Destination file is created. Source file is open Destination file is open. temp value is 400. 0 soure_file size is 9496. destination_file size is 0x2800. check sum generated is 0x68D92007. Everything is ok. rm -rf *.o arch/arm/mach-sunxi/pm/standby/../*.o CC arch/arm/mach-sunxi/pm/mem_mapping.o CC arch/arm/mach-sunxi/pm/mem_divlibc.o CC arch/arm/mach-sunxi/pm/mem_cpu.o AS arch/arm/mach-sunxi/pm/mem_cpu_asm.o AS arch/arm/mach-sunxi/pm/mem_mmu_pc_asm.o CC arch/arm/mach-sunxi/pm/mem_mmu_pc.o CC arch/arm/mach-sunxi/pm/mem_int.o CC arch/arm/mach-sunxi/pm/mem_clk.o CC arch/arm/mach-sunxi/pm/mem_tmr.o CC arch/arm/mach-sunxi/pm/mem_tmstmp.o CC arch/arm/mach-sunxi/pm/mem_twi.o CC arch/arm/mach-sunxi/pm/mem_gpio.o CC arch/arm/mach-sunxi/pm/mem_sram.o CC arch/arm/mach-sunxi/pm/mem_ccu.o CC arch/arm/mach-sunxi/pm/mem_cci400.o CC arch/arm/mach-sunxi/pm/mem_gtbus.o CC arch/arm/mach-sunxi/pm/pm_debug.o CC arch/arm/mach-sunxi/pm/mem_timing.o CC arch/arm/mach-sunxi/pm/mem_hwspinlock.o CC arch/arm/mach-sunxi/pm/pm.o CC arch/arm/mach-sunxi/pm/extended_standby.o CC arch/arm/mach-sunxi/pm/standby/super/super_power.o CC arch/arm/mach-sunxi/pm/standby/super/super_twi.o CC arch/arm/mach-sunxi/pm/standby/super/super_clock.o AS arch/arm/mach-sunxi/pm/standby.o AS arch/arm/mach-sunxi/pm/mem.o LD arch/arm/mach-sunxi/pm/pm_tmp.o LD arch/arm/mach-sunxi/pm/built-in.o LD arch/arm/mach-sunxi/built-in.o make[3]: *** [drivers/net/wireless/bcmdhd] 错误 2 make[2]: *** [drivers/net/wireless] 错误 2 make[1]: *** [drivers/net] 错误 2 make: *** [drivers] 错误 2 ERROR: build kernel Failed rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ 21、（dhdsdio_probe_attach: unsupported chip: 0xa9a6） R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd\include\bcmdevs.h #define BCM4350_CHIP_ID 0x4350 #define BCM43430_CHIP_ID 43430 /* 43430 chipcommon chipid 0xa9a6 */ #define BCM4342_CHIP_ID 4342 可以编译通过了。 （查看属性：） shell@astar-y3:/ $ shell@astar-y3:/ $ cd /system/vendor/modules/ shell@astar-y3:/system/vendor/modules $ ll bcm* -rw-r--r-- root root 26020 2017-06-26 12:46 bcm43438a0.hcd -rw-r--r-- root root 748856 2017-06-26 12:46 bcmdhd.ko shell@astar-y3:/system/vendor/modules $ Microsoft Windows [版本 6.1.7600] 版权所有 (c) 2009 Microsoft Corporation。保留所有权利。 C:\Users\Administrator>cd R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\n et\wireless\bcmdhd C:\Users\Administrator>r: R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd>adb remount * daemon not running. starting it now on port 5037 * * daemon started successfully * remount succeeded R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd> R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd>adb push bcmdhd.ko /system/vendor/modules/ 1677 KB/s (748864 bytes in 0.436s) R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd> 继续查看属性： shell@astar-y3:/system/vendor/modules $ ll bcm* -rw-r--r-- root root 26020 2017-06-26 12:46 bcm43438a0.hcd -rw-rw-rw- root root 748864 2017-06-26 14:34 bcmdhd.ko shell@astar-y3:/system/vendor/modules $ shell@astar-y3:/system/vendor/modules $ shell@astar-y3:/system/vendor/modules $ chmod 644 bcmdhd.ko Unable to chmod bcmdhd.ko: Operation not permitted 10|shell@astar-y3:/system/vendor/modules $ （必须在su下才能够修改属性：） shell@astar-y3:/system/vendor/modules $ su shell@astar-y3:/system/vendor/modules # chmod 644 bcmdhd.ko shell@astar-y3:/system/vendor/modules # shell@astar-y3:/system/vendor/modules # sync shell@astar-y3:/system/vendor/modules # reboot 22、 [ 0.658241] [wifi]: select wifi: ap6210 !! [ 0.658587] [ap6xxx]: module power name axp22_dldo1 [ 0.658601] [ap6xxx]: module power ext1 name axp22_dldo2 [ 0.658613] [ap6xxx]: module power ext2 name axp22_aldo1 [ 0.658721] [ap6xxx]: get ap6xxx wifi_power_switch failed [ 0.658731] [ap6xxx]: ap6xxx module power set by axp. [ 0.658930] [ap6xxx]: first time [ 0.659285] [ap6xxx]: regulator on. [ 0.661306] [wifi_pm]: wifi gpio init is OK !! （重启之后，WIFI模块要想办法配置为ap6212，现阶段借用的是AP6210！） [ 8.517657] gpio ap6xxx_wl_regon set val 1, act val 1 [ 8.623325] [ap6xxx]: sdio wifi power state: on [ 8.628389] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.628566] =========== WLAN placed in POWER ON ======== [ 8.645459] [mmc]: sdc1 card_power_on start... [ 8.650397] [mmc]: sdc1 power_supply is null [ 8.655129] [mmc]: sdc1 card_power_on ok [ 8.680031] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.690267] [mmc]: mclk 0xf1c2008c 0x8002000e [ 8.772360] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 8.781316] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 8.789448] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.799684] [mmc]: mclk 0xf1c2008c 0x8002000e [ 8.861971] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.872189] [mmc]: mclk 0xf1c2008c 0x8002000e [ 8.933887] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 8, RTO !! [ 8.941921] *******************Try sdio******************* [ 8.948329] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.958545] [mmc]: mclk 0xf1c2008c 0x8002000e [ 9.027690] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 9.035325] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 9.043192] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 9.052046] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 9.145358] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 9.155486] [mmc]: mclk 0xf1c2008c 0x8002000e [ 9.215398] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 9.225785] [mmc]: mclk 0xf1c2008c 0x8100000b [ 9.285721] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 9.296049] [mmc]: mclk 0xf1c2008c 0x8140030b [ 9.357922] mmc1: new high speed SDIO card at address 0001 [ 9.364523] bcmsdh_register: Linux Kernel SDIO/MMC Driver [ 9.364563] *******************sdio init ok******************* [ 9.377203] bcm_wlan_get_oob_irq enter. [ 9.381534] gpio [359] map to virq [7] ok [ 9.388816] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4 [ 9.396740] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 9.404660] dhdsdio_probe: Disable prop_txstatus [ 9.410903] wl_create_event_handler(): thread:wl_event_handler:5d started [ 9.410914] tsk Enter, tsk = 0xddca13d8 [ 9.423788] p2p0: P2P Interface Registered [ 9.428464] dhd_attach(): thread:dhd_watchdog_thread:5e started [ 9.435144] dhd_attach(): thread:dhd_dpc:5f started [ 9.440653] dhd_attach(): thread:dhd_sysioc:60 started [ 9.447276] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 [ 9.456558] [ 9.456561] Dongle Host Driver, version 1.88.45.3 (r420671) [ 9.456565] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 14:34:04 [ 9.472427] gpio ap6xxx_wl_regon set val 0, act val 0 [ 9.578054] [ap6xxx]: sdio wifi power state: off [ 9.583186] =========== WLAN placed in RESET ======== （WIFI启动加载正常） shell@astar-y3:/ $ lsmod gt82x 9849 0 - Live 0x00000000 sunxi_schw 12559 0 - Live 0x00000000 (O) cdc_ether 5099 0 - Live 0x00000000 rtl8150 9023 0 - Live 0x00000000 mcs7830 6292 0 - Live 0x00000000 qf9700 7805 0 - Live 0x00000000 asix 17150 0 - Live 0x00000000 usbnet 17700 4 cdc_ether,mcs7830,qf9700,asix, Live 0x00000000 sunxi_keyboard 3021 0 - Live 0x00000000 sw_device 13604 0 - Live 0x00000000 vfe_v4l2 445364 0 - Live 0x00000000 gc2035 12696 0 - Live 0x00000000 gc0308 10702 0 - Live 0x00000000 vfe_subdev 4523 3 vfe_v4l2,gc2035,gc0308, Live 0x00000000 vfe_os 4099 2 vfe_v4l2,vfe_subdev, Live 0x00000000 cci 21594 2 gc2035,gc0308, Live 0x00000000 videobuf_dma_contig 5535 1 vfe_v4l2, Live 0x00000000 videobuf_core 16520 2 vfe_v4l2,videobuf_dma_contig, Live 0x00000000 bcmdhd 556965 0 - Live 0x00000000 leds_sunxi 1351 0 - Live 0x00000000 mali 209914 20 - Live 0x00000000 (O) lcd 38180 0 - Live 0x00000000 disp 993096 8 mali,lcd, Live 0x00000000 nand 280622 0 - Live 0x00000000 (O) shell@astar-y3:/ $ （bcmdhd.ko这个驱动模块加载正常：） （BT没有打开，但是不停地打印BT超时出错，不知道是何解？） shell@astar-y3:/ $ [ 511.880344] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [ 511.887326] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle 23、 由于此时WIFI出于记住上一次的状态的状态（打不开），所以需要重新刷镜像IMG，然后替换：bcmdhd.ko shell@astar-y3:/ $ shell@astar-y3:/ $ lsmod gt82x 9849 0 - Live 0x00000000 sunxi_schw 12559 0 - Live 0x00000000 (O) cdc_ether 5099 0 - Live 0x00000000 rtl8150 9023 0 - Live 0x00000000 mcs7830 6292 0 - Live 0x00000000 qf9700 7805 0 - Live 0x00000000 asix 17150 0 - Live 0x00000000 usbnet 17700 4 cdc_ether,mcs7830,qf9700,asix, Live 0x00000000 sunxi_keyboard 3021 0 - Live 0x00000000 sw_device 13604 0 - Live 0x00000000 vfe_v4l2 445364 0 - Live 0x00000000 gc2035 12696 0 - Live 0x00000000 gc0308 10702 0 - Live 0x00000000 vfe_subdev 4523 3 vfe_v4l2,gc2035,gc0308, Live 0x00000000 vfe_os 4099 2 vfe_v4l2,vfe_subdev, Live 0x00000000 cci 21594 2 gc2035,gc0308, Live 0x00000000 videobuf_dma_contig 5535 1 vfe_v4l2, Live 0x00000000 videobuf_core 16520 2 vfe_v4l2,videobuf_dma_contig, Live 0x00000000 bcmdhd 556965 0 - Live 0x00000000 leds_sunxi 1351 0 - Live 0x00000000 mali 209914 15 - Live 0x00000000 (O) lcd 38180 0 - Live 0x00000000 disp 993096 8 mali,lcd, Live 0x00000000 nand 280622 0 - Live 0x00000000 (O) shell@astar-y3:/ $ shell@astar-y3:/ $ shell@astar-y3:/ $ [ 110.012176] init: computing context for service '/system/bin/wpa_supplicant' [ 110.025400] init: starting 'p2p_supplicant' [ 110.039886] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 110.119751] dhd_conf_set_fw_name_by_chip: firmware_path=/system/vendor/modules/fw_bcm43438a0.bin [ 110.140144] [ 110.140153] Dongle Host Driver, version 1.88.45.3 (r420671) [ 110.140158] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 14:34:04 [ 110.173523] wl_android_wifi_on in 1 [ 110.177409] wl_android_wifi_on in 2: g_wifi_on=0 [ 110.200103] gpio ap6xxx_wl_regon set val 1, act val 1 [ 110.280025] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [ 110.286694] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle [ 110.355684] [ap6xxx]: sdio wifi power state: on [ 110.360930] =========== WLAN going back to live ======== [ 110.366925] sdio_reset_comm(): [ 110.370346] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.380773] [mmc]: mclk 0xf1c2008c 0x8140030b [ 110.443029] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.454758] [mmc]: mclk 0xf1c2008c 0x8140030b [ 110.516097] [mmc]: sdc1 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.530958] [mmc]: mclk 0xf1c2008c 0x80430309 [ 110.592013] [mmc]: sdc1 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.603518] [mmc]: mclk 0xf1c2008c 0x80030009 [ 110.681418] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 110.690726] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 110.700331] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 110.712218] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 110.894520] [mmc]: sdc1 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.904933] [mmc]: mclk 0xf1c2008c 0x80030009 [ 110.964907] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.975514] [mmc]: mclk 0xf1c2008c 0x8100000b [ 111.035618] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 111.046398] [mmc]: mclk 0xf1c2008c 0x8140030b [ 111.108547] [ 111.108566] [ 111.108579] dhd_bus_devreset: == WLAN ON == [ 111.116882] dhd_bus_devreset called when dongle is not in reset [ 111.123683] Will call dhd_bus_start instead [ 111.128637] dhd_conf_set_fw_name_by_chip: firmware_path=/system/vendor/modules/fw_bcm43438a0.bin [ 111.140963] dhd_conf_download_config: Ignore config file /system/vendor/modules/config.txt [ 111.151802] Final fw_path=/system/vendor/modules/fw_bcm43438a0.bin [ 111.158689] Final nv_path=/system/vendor/modules/nvram_ap6210.txt [ 111.165542] Final conf_path=/system/vendor/modules/config.txt [ 111.257577] dhdsdio_download_nvram: Open nvram file failed /system/vendor/modules/nvram_ap6210.txt [ 111.268309] _dhdsdio_download_firmware: dongle nvram file download failed [ 111.276022] dhd_bus_start: dhdsdio_probe_download failed. firmware = /system/vendor/modules/fw_bcm43438a0.bin nvram = /system/vendor/modules/nvram_ap6210.txt config = /system/vendor/modules/config.txt [ 111.295979] dhd_bus_devreset: dhd_bus_start fail with -1 [ 111.304154] dhd_dev_reset: dhd_bus_devreset: -1 [ 111.309190] dhd_prot_ioctl : bus is down. we have nothing to do [ 111.330328] dhd_bus_devreset: WLAN OFF DONE [ 111.335225] gpio ap6xxx_wl_regon set val 0, act val 0 [ 111.472499] [ap6xxx]: sdio wifi power state: off [ 111.477661] =========== WLAN placed in RESET ======== [ 111.483304] wl_android_wifi_on: Failed [ 111.487473] wl_android_wifi_off in 1 [ 111.491478] wl_android_wifi_off in 2: g_wifi_on=0 [ 111.496711] wl_android_wifi_off out [ 111.509335] init: waitpid returned pid 1211, status = 0000ff00 [ 111.516072] init: process 'p2p_supplicant', pid 1211 exited shell@astar-y3:/ $ shell@astar-y3:/ $ 24、定位问题：dhd_bus_devreset: dhd_bus_start fail with -1 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "dhd_bus_start fail with" . -R ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "dhd_bus_start fail with" . -R ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ int dhd_bus_devreset(dhd_pub_t *dhdp, uint8 flag) { …… dhd_conf_set_fw_name_by_chip(dhdp, fw_path, firmware_path); if ((bcmerror = dhd_bus_start(dhdp)) != 0) DHD_ERROR(("%s: dhd_bus_start fail with %d\n", __FUNCTION__, bcmerror)); } } return bcmerror; } rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep dhd_bus_start . -R ./dhd_sdio.c: if ((ret = dhd_bus_start(bus->dhd)) != 0) { ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__)); ./dhd_sdio.c: DHD_ERROR(("Will call dhd_bus_start instead\n")); ./dhd_sdio.c: if ((bcmerror = dhd_bus_start(dhdp)) != 0) ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", ./dhd_sdio - 副本.c: if ((ret = dhd_bus_start(bus->dhd)) != 0) { ./dhd_sdio - 副本.c: DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__)); ./dhd_sdio - 副本.c: DHD_ERROR(("Will call dhd_bus_start instead\n")); ./dhd_sdio - 副本.c: if ((bcmerror = dhd_bus_start(dhdp)) != 0) ./dhd_sdio - 副本.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", ./dhd_sdio - 副本 (2).c: if ((ret = dhd_bus_start(bus->dhd)) != 0) { ./dhd_sdio - 副本 (2).c: DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__)); ./dhd_sdio - 副本 (2).c: DHD_ERROR(("Will call dhd_bus_start instead\n")); ./dhd_sdio - 副本 (2).c: if ((bcmerror = dhd_bus_start(dhdp)) != 0) ./dhd_sdio - 副本 (2).c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", ./dhd.h:extern int dhd_bus_start(dhd_pub_t *dhdp); ./wl_android.c:/* Initialize g_wifi_on to 1 so dhd_bus_start will be called for the first ./dhd_linux.c: if ((ret = dhd_bus_start(&dhd->pub)) != 0) { ./dhd_linux.c: /* dhd_prot_init has been called in dhd_bus_start or wl_android_wifi_on */ ./dhd_linux.c:dhd_bus_start(dhd_pub_t *dhdp) rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ 定位到这里： int dhd_bus_start(dhd_pub_t *dhdp) { …… /* try to download image and nvram to the dongle */ if ((dhd->pub.busstate == DHD_BUS_DOWN) && (fw_path[0] != '\0') && (nv_path[0] != '\0')) { #ifdef SHOW_NVRAM_TYPE { /* Show nvram type in the kernel log */ int i; for (i = 0; nv_path[i] != '\0'; ++i) { if (nv_path[i] == '.') { ++i; break; } } DHD_ERROR(("%s: nvram_type = [%s]\n", __FUNCTION__, &nv_path[i])); } #endif /* SHOW_NVRAM_TYPE */ /* wake lock moved to dhdsdio_download_firmware */ if (!(dhd_bus_download_firmware(dhd->pub.bus, dhd->pub.osh, fw_path, nv_path, conf_path))) { DHD_ERROR(("%s: dhdsdio_probe_download failed. firmware = %s nvram = %s config = %s\n", __FUNCTION__, fw_path, nv_path, conf_path)); #ifdef DHDTHREAD if (dhd->threads_only) dhd_os_sdunlock(dhdp); #endif /* DHDTHREAD */ // 2017/6/23 18:40 wenyuanbo download ap6212 fail not return error!!!! //return -1; } } …… return 0; } 由于ap6212没有config.txt文件，下载肯定会出错，比对全志R16平台去AP6212的处理，关闭这里： //return -1; 25、 shell@astar-y3:/ $ shell@astar-y3:/ $ [ 110.012176] init: computing context for service '/system/bin/wpa_supplicant' [ 110.025400] init: starting 'p2p_supplicant' [ 110.039886] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 110.119751] dhd_conf_set_fw_name_by_chip: firmware_path=/system/vendor/modules/fw_bcm43438a0.bin [ 110.140144] [ 110.140153] Dongle Host Driver, version 1.88.45.3 (r420671) [ 110.140158] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 14:34:04 [ 110.173523] wl_android_wifi_on in 1 [ 110.177409] wl_android_wifi_on in 2: g_wifi_on=0 [ 110.200103] gpio ap6xxx_wl_regon set val 1, act val 1 [ 110.280025] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expire
7z

ap6212a0_a33_sc3817r_服务器验证通过_bt已经通了_wifi需要修改配置_需要再次验证_20170626_1549.7z

调通sina33下的AP6212A0版本的BT 大文实验室/大文哥 壹捌陆捌零陆捌捌陆捌贰 wb4916 AT qq.com 完成时间：2017/6/26 11:01 版本：V1.0 本文参照： 《A33 wifi移植说明书.pdf》 还有就是全志R16的parrotv1.1的官方SDK（Android4.4.2） 1、打开AP6212的BT，关闭rtl8723bs的BT： [ 3.141273] Bluetooth: HCI UART driver ver 2.2 [ 3.146210] Bluetooth: HCI H4 protocol initialized [ 3.151563] Bluetooth: HCI BCSP protocol initialized [ 3.157154] usbcore: registered new interface driver btusb [ 3.163282] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 3.169599] Bluetooth: BlueSleep Mode Driver Ver 1.1 [ 3.175402] Bluetooth: get rtl8723bs rtl8723bs_bt_host_wake gpio failed [ 3.953017] Bluetooth: RFCOMM TTY layer initialized [ 3.958456] Bluetooth: RFCOMM socket layer initialized [ 3.964183] Bluetooth: RFCOMM ver 1.11 [ 3.968340] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.968638] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 3.968734] [mmc]: mclk 0xf1c20090 0xc100000b [ 3.989421] Bluetooth: BNEP filters: protocol multicast [ 3.995242] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.001921] L2TP core driver, V2.0 [ 4.005706] PPPoL2TP kernel driver, V2.0 [ 4.010070] L2TP IP encapsulation support (L2TPv3) [ 4.015468] L2TP netlink interface [ 4.019264] L2TP ethernet pseudowire support (L2TPv3) [ 4.023860] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B [ 4.023929] [mmc]: mclk 0xf1c20090 0xc100000b [ 4.040272] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 4.048780] ThumbEE CPU extension supported. [ 4.053550] Registering SWP/SWPB emulation handler [ 4.059269] [rfkill]: rfkill set power 1 [ 4.063652] gpio ap6xxx_bt_regon set val 0, act val 0 正常启动的BT加载： [ 3.207764] Bluetooth: HCI UART driver ver 2.2 [ 3.212725] Bluetooth: HCI H4 protocol initialized [ 3.218045] Bluetooth: HCI BCSP protocol initialized [ 3.223671] usbcore: registered new interface driver btusb [ 3.229766] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 3.236243] Bluetooth: MSM Sleep Mode Driver Ver 1.2 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r$ ll rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh config Welcome to mkscript setup progress All available chips: 0. sun8iw5p1 Choice: 0 All available platforms: 0. android 1. dragonboard 2. linux Choice: 0 All available kernel: 0. linux-3.4 Choice: 0 All available boards: 0. evb 1. maple 2. redwood 3. y2 4. y3 Choice: 4 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4$ make ARCH=arm menuconfig [*] Networking support ---> Bluetooth subsystem support ---> Bluetooth device drivers ---> Broadcom Bluetooth Low Power Manager Support Realtek Bluesleep driver support 修改为： Broadcom Bluetooth Low Power Manager Support An inverter between bt hostwake pin and cpu (NEW) Realtek Bluesleep driver support 2、（这个不修改：） R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\overlay\frameworks\base\core\res\res\values\config.xml "wlan0" "bt-pan" 3、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\astar_y3.mk # ap6181/6210/6330 sdio wifi fw and nvram #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6181/device-bcm.mk) #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6210/device-bcm.mk) $(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6212/device-bcm.mk) #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6330/device-bcm.mk) #rtl8723bs bt fw and config #$(call inherit-product, hardware/realtek/bluetooth/rtl8723bs/firmware/rtlbtfw_cfg.mk) # camera config for camera detector #PRODUCT_COPY_FILES += \ # device/softwinner/astar-y3/hawkview/sensor_list_cfg.ini:system/etc/hawkview/sensor_list_cfg.ini #add gms features #PRODUCT_COPY_FILES += \ # frameworks/native/data/etc/android.hardware.faketouch.xml:system/etc/permissions/android.hardware.faketouch.xml \ # frameworks/native/data/etc/android.hardware.touchscreen.multitouch.jazzhand.xml:system/etc/permissions/android.hardware.touchscreen.multitouch.jazzhand.xml \ # frameworks/native/data/etc/android.hardware.usb.host.xml:system/etc/permissions/android.hardware.usb.host.xml # 3G Data Card Packages #PRODUCT_PACKAGES += \ # u3gmonitor \ # chat \ # rild \ # pppd # 3G Data Card Configuration Flie #PRODUCT_COPY_FILES += \ # device/softwinner/polaris-common/rild/ip-down:system/etc/ppp/ip-down \ # device/softwinner/polaris-common/rild/ip-up:system/etc/ppp/ip-up \ # device/softwinner/polaris-common/rild/3g_dongle.cfg:system/etc/3g_dongle.cfg \ # device/softwinner/polaris-common/rild/usb_modeswitch:system/bin/usb_modeswitch \ # device/softwinner/polaris-common/rild/call-pppd:system/xbin/call-pppd \ # device/softwinner/polaris-common/rild/usb_modeswitch.sh:system/xbin/usb_modeswitch.sh \ # device/softwinner/polaris-common/rild/apns-conf_sdk.xml:system/etc/apns-conf.xml \ # device/softwinner/polaris-common/rild/libsoftwinner-ril.so:system/lib/libsoftwinner-ril.so #PRODUCT_COPY_FILES += \ # device/softwinner/polaris-common/rild/init.3gdongle.rc:root/init.sunxi.3gdongle.rc # 3G Data Card usb modeswitch File #PRODUCT_COPY_FILES += \ # $(call find-copy-subdir-files,*,device/softwinner/polaris-common/rild/usb_modeswitch.d,system/etc/usb_modeswitch.d) PRODUCT_PROPERTY_OVERRIDES += \ ro.sw.embeded.telephony = false PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.timezone=Asia/Shanghai \ persist.sys.language=zh \ persist.sys.country=CN PRODUCT_PACKAGES += Bluetooth #PRODUCT_PROPERTY_OVERRIDES += \ # ro.product.8723b_bt.used=true #GPS Feature #PRODUCT_PACKAGES += gps.polaris #BOARD_USES_GPS_TYPE := simulator #PRODUCT_COPY_FILES += frameworks/native/data/etc/android.hardware.location.xml:system/etc/permissions/android.hardware.location.xml # evb logger PRODUCT_COPY_FILES += \ device/softwinner/astar-y3/tools/logger.sh:system/bin/logger.sh PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.usb.config=mass_storage,adb \ ro.adb.secure=0 ro.udisk.lable=Polaris \ ro.font.scale=1.0 \ ro.hwa.force=false \ rw.logger=0 \ ro.sys.bootfast=true \ debug.hwc.showfps=0 \ debug.hwui.render_dirty_regions=false #ro.sys.storage_type = emulated \ #for gms #PRODUCT_PROPERTY_OVERRIDES += \ # ro.sys.mutedrm=true \ # ro.adb.secure=1 PRODUCT_PROPERTY_OVERRIDES += \ ro.sf.lcd_density=213 \ ro.product.firmware=v2.0 $(call inherit-product-if-exists, device/softwinner/astar-y3/modules/modules.mk) DEVICE_PACKAGE_OVERLAYS := device/softwinner/astar-y3/overlay PRODUCT_CHARACTERISTICS := tablet # Overrides PRODUCT_AAPT_CONFIG := xlarge hdpi xhdpi large PRODUCT_AAPT_PREF_CONFIG := xhdpi PRODUCT_BRAND := Allwinner PRODUCT_NAME := astar_y3 PRODUCT_DEVICE := astar-y3 PRODUCT_MODEL := QUAD-CORE A33 y3 PRODUCT_MANUFACTURER := softwinner #include device/softwinner/polaris-common/prebuild/google/products/gms_base.mk 4、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\BoardConfig.mk # wifi and bt configuration # 1. Wifi Configuration # 1.1 realtek wifi support # 1.1 realtek wifi configuration #BOARD_WIFI_VENDOR := realtek ifeq ($(BOARD_WIFI_VENDOR), realtek) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_rtl BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_rtl SW_BOARD_USR_WIFI := rtl8188eu BOARD_WLAN_DEVICE := rtl8188eu #SW_BOARD_USR_WIFI := rtl8723au #BOARD_WLAN_DEVICE := rtl8723au #SW_BOARD_USR_WIFI := rtl8723bs #BOARD_WLAN_DEVICE := rtl8723bs endif # 1.2 broadcom wifi support BOARD_WIFI_VENDOR := broadcom ifeq ($(BOARD_WIFI_VENDOR), broadcom) BOARD_WPA_SUPPLICANT_DRIVER := NL80211 WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_WLAN_DEVICE := bcmdhd WIFI_DRIVER_FW_PATH_PARAM := "/sys/module/bcmdhd/parameters/firmware_path" #SW_BOARD_USR_WIFI := AP6181 #SW_BOARD_USR_WIFI := AP6210 #WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm40181a2.bin" #WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm40181a2_p2p.bin" #WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm40181a2_apsta.bin" # 2017/6/21 15:11 wenyuanbo configure ap6212 use ap6210 SW_BOARD_USR_WIFI := AP6212 WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm43438a0.bin" WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm43438a0_p2p.bin" WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm43438a0_apsta.bin" #SW_BOARD_USR_WIFI := AP6330 #WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm40183b2_ag.bin" #WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm40183b2_ag_p2p.bin" #WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm40183b2_ag_apsta.bin" endif #1.3 eag wifi config #BOARD_WIFI_VENDOR := eagle ifeq ($(BOARD_WIFI_VENDOR), eagle) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_eagle BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_eagle SW_BOARD_USR_WIFI := esp8089 BOARD_WLAN_DEVICE := esp8089 endif # 2. Bluetooth Configuration # make sure BOARD_HAVE_BLUETOOTH is true for every bt vendor BOARD_HAVE_BLUETOOTH := true BOARD_HAVE_BLUETOOTH_BCM := true #SW_BOARD_HAVE_BLUETOOTH_NAME := ap6210 SW_BOARD_HAVE_BLUETOOTH_NAME := ap6212 #SW_BOARD_HAVE_BLUETOOTH_NAME := ap6330 #BOARD_HAVE_BLUETOOTH_RTK := true #BLUETOOTH_HCI_USE_RTK_H5 := true #SW_BOARD_HAVE_BLUETOOTH_NAME := rtl8723bs 5、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\init.sun8i.rc on early-fs mount_all /fstab.sun8i setprop ro.crypto.fuse_sdcard true insmod /system/vendor/modules/disp.ko insmod /system/vendor/modules/lcd.ko insmod /system/vendor/modules/mali.ko insmod /system/vendor/modules/leds-sunxi.ko insmod /system/vendor/modules/bcmdhd.ko insmod /system/vendor/modules/bcm_btlpm.ko #2G or 3G init.rc # import init.sunxi.3gdongle.rc ## 1. realtek & eagle wifi service ## 1.1 realtek & eagle wifi sta service #service wpa_supplicant /system/bin/wpa_supplicant \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -O/data/misc/wifi/sockets \ # -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # # we will start as root and wpa_supplicant will switch to user wifi # # after setting up the capabilities required for WEXT # # user wifi # # group wifi inet keystore # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # ## 1.2 realtek & eagle wifi sta p2p concurrent service #service p2p_supplicant /system/bin/wpa_supplicant \ # -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ # -e/data/misc/wifi/entropy.bin -N \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -O/data/misc/wifi/sockets \ # -g@android:wpa_wlan0 # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # 2. broadcom wifi service # 2.1 broadcom wifi station and softap service wpa_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -I/system/etc/wifi/wpa_supplicant_overlay.conf \ -O/data/misc/wifi/sockets \ -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot # 2.2 broadcom wifi sta p2p concurrent service service p2p_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -I/system/etc/wifi/wpa_supplicant_overlay.conf \ -O/data/misc/wifi/sockets -N \ -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ -I/system/etc/wifi/p2p_supplicant_overlay.conf \ -puse_p2p_group_interface=1 -e/data/misc/wifi/entropy.bin \ -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot 6、（不需要修改） R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\ueventd.sun8i.rc 7、 R:\wyb\ap6212a0_a33_sc3817r\android\frameworks\base\packages\SettingsProvider\res\values\defaults.xml 1800000 true 8、 R:\wyb\ap6212a0_a33_sc3817r\android\frameworks\base\services\java\com\android\server\BatteryService.java // private static final boolean DEBUG = false; private static final boolean DEBUG = true; private void sendIntentLocked() { // Pack up the values and broadcast them to everyone final Intent intent = new Intent(Intent.ACTION_BATTERY_CHANGED); intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY | Intent.FLAG_RECEIVER_REPLACE_PENDING); int icon = getIconLocked(mBatteryProps.batteryLevel); intent.putExtra(BatteryManager.EXTRA_STATUS, mBatteryProps.batteryStatus); intent.putExtra(BatteryManager.EXTRA_HEALTH, mBatteryProps.batteryHealth); intent.putExtra(BatteryManager.EXTRA_PRESENT, mBatteryProps.batteryPresent); //intent.putExtra(BatteryManager.EXTRA_LEVEL, mBatteryProps.batteryLevel); intent.putExtra(BatteryManager.EXTRA_LEVEL, 100); intent.putExtra(BatteryManager.EXTRA_SCALE, BATTERY_SCALE); intent.putExtra(BatteryManager.EXTRA_ICON_SMALL, icon); intent.putExtra(BatteryManager.EXTRA_PLUGGED, mPlugType); //intent.putExtra(BatteryManager.EXTRA_VOLTAGE, mBatteryProps.batteryVoltage); intent.putExtra(BatteryManager.EXTRA_VOLTAGE, 4200); intent.putExtra(BatteryManager.EXTRA_TEMPERATURE, mBatteryProps.batteryTemperature); intent.putExtra(BatteryManager.EXTRA_TECHNOLOGY, mBatteryProps.batteryTechnology); intent.putExtra(BatteryManager.EXTRA_INVALID_CHARGER, mInvalidCharger); if (DEBUG) { Slog.d(TAG, "2016/12/05 10:41 wenyuanbo **** Sending ACTION_BATTERY_CHANGED. level:" + mBatteryProps.batteryLevel + ", scale:" + BATTERY_SCALE + ", status:" + mBatteryProps.batteryStatus + ", health:" + mBatteryProps.batteryHealth + ", present:" + mBatteryProps.batteryPresent + ", voltage: " + mBatteryProps.batteryVoltage + ", temperature: " + mBatteryProps.batteryTemperature + ", technology: " + mBatteryProps.batteryTechnology + ", AC powered:" + mBatteryProps.chargerAcOnline + ", USB powered:" + mBatteryProps.chargerUsbOnline + ", Wireless powered:" + mBatteryProps.chargerWirelessOnline + ", icon:" + icon + ", invalid charger:" + mInvalidCharger); } mHandler.post(new Runnable() { @Override public void run() { ActivityManagerNative.broadcastStickyIntent(intent, null, UserHandle.USER_ALL); } }); } 9、（直接拷贝同目录下的ap6210：） R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\conf\softwinner\ap6212\Android.mk LOCAL_PATH := $(call my-dir) include $(CLEAR_VARS) LOCAL_MODULE := bt_vendor.conf LOCAL_MODULE_CLASS := ETC LOCAL_MODULE_PATH := $(TARGET_OUT)/etc/bluetooth LOCAL_MODULE_TAGS := eng LOCAL_SRC_FILES := $(LOCAL_MODULE) include $(BUILD_PREBUILT) R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\conf\softwinner\ap6212\bt_vendor.conf # UART device port where Bluetooth controller is attached UartPort = /dev/ttyS1 # Firmware patch file location FwPatchFilePath = /system/vendor/modules/ # Firmware Name FwPatchFileName = bcm43438a0.hcd 10、新增：vnd_astar-y3-ap6212.txt，直接拷贝：vnd_astar-y2-ap6210.txt R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\include\vnd_astar-y3-ap6212.txt R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\include\vnd_astar-y2-ap6210.txt BLUETOOTH_UART_DEVICE_PORT = "/dev/ttyS1" FW_PATCHFILE_LOCATION = "/system/vendor/modules/" LPM_IDLE_TIMEOUT_MULTIPLE = 5 UART_TARGET_BAUD_RATE = 1500000 BT_WAKE_VIA_PROC = TRUE #LPM_SLEEP_MODE = FALSE BTVND_DBG = TRUE BTHW_DBG = TRUE VNDUSERIAL_DBG = TRUE UPIO_DBG = TRUE 11、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\src\userial_vendor.c //#ifdef USE_AP6210_BT_MODULE #if defined(USE_AP6210_BT_MODULE) || defined(USE_AP6212_BT_MODULE) /* PATCH for AP6210. Will detect CTS(module side) to select transport mode*/ ALOGE("userial vendor open: USE AP6210 BT MODULE."); usleep(100000); close(vnd_userial.fd); if ((vnd_userial.fd = open(vnd_userial.port_name, O_RDWR)) == -1) { ALOGE("userial vendor open: unable to open %s", vnd_userial.port_name); return -1; } #endif //USE_AP6210_BT_MODULE 12、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\Android.mk ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) LOCAL_CFLAGS += -DUSE_AP6210_BT_MODULE endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) LOCAL_CFLAGS += -DUSE_AP6212_BT_MODULE endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6330) include $(LOCAL_PATH)/conf/softwinner/ap6330/Android.mk endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) include $(LOCAL_PATH)/conf/softwinner/ap6210/Android.mk endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) include $(LOCAL_PATH)/conf/softwinner/ap6212/Android.mk endif 13、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\vnd_buildcfg.mk ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) SRC := $(call my-dir)/include/$(addprefix vnd_, $(addsuffix -ap6210.txt,$(basename $(TARGET_DEVICE)))) endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) SRC := $(call my-dir)/include/$(addprefix vnd_, $(addsuffix -ap6212.txt,$(basename $(TARGET_DEVICE)))) endif 14、（这些AP6212的WIFI的bin文件和BT的hcd文件来自全志R16的SDK，当然也可以找正基原厂/代理商索取：） R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\bcm43438a0.hcd （根据ap6210修改：） R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\device-bcm.mk # # Copyright (C) 2008 The Android Open Source Project # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # ######################## -include hardware/broadcom/wlan/bcmdhd/config/config-bcm.mk PRODUCT_COPY_FILES += \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0.bin:system/vendor/modules/fw_bcm43438a0.bin \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0_apsta.bin:system/vendor/modules/fw_bcm43438a0_apsta.bin \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0_p2p.bin:system/vendor/modules/fw_bcm43438a0_p2p.bin \ hardware/broadcom/wlan/firmware/ap6212/nvram_ap6212.txt:system/vendor/modules/nvram_ap6212.txt \ hardware/broadcom/wlan/firmware/ap6212/bcm43438a0.hcd:system/vendor/modules/bcm43438a0.hcd #hardware/broadcom/wlan/firmware/ap6212/config.txt:system/vendor/modules/config.txt ######################## R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0_apsta.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0_p2p.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\nvram_ap6212.txt 15、（可选修改：） R:\wyb\ap6212a0_a33_sc3817r\android\packages\apps\Camera2\src\com\android\camera\CameraActivity.java private BroadcastReceiver mBatteryInfoReceiver = new BroadcastReceiver() { @Override public void onReceive(Context context, Intent intent) { String action = intent.getAction(); if (Intent.ACTION_BATTERY_CHANGED.equals(action)) { int Level = intent.getIntExtra("level", 0); int Scale = intent.getIntExtra("scale", 100); Log.w(TAG, "2016/11/29 19:54 &&&& wenyuanbo battery Level" + Level); /* *Logic: *1.the battery level is lower then 5%. *2.if in camera, make sure that not in the snapshot progress. *3.if in videocamera, make sure that not in the videorecording progress. *4.everytime starting the camera activity, the battery level is broadcasted, * if meeting the conditions above, give a dialog, press it and finish the activity. *5.if the conditions are not satisfied when started, play for a moment, in the camera acitvity * or video camera activity, the conditiosn are satisfied, also give a dialog for finishing the activity. * *by fuqiang. */ if(Level < 5) { Runnable runnable_close_camera = new Runnable() { @Override public void run() { //close the camera. // CameraActivity.this.finish(); } }; Log.w(TAG, "2016/11/29 18:20 **** wenyuanbo battery Level" + Level); showLocationDialog(); } /* *Logic: *1.the battery level is lhigher then 5% and lower than 15%. *2.if in camera, make sure that not in the snapshot progress. *3.if in videocamera, make sure that not in the videorecording progress. *4.whether in camera or in videocamera, make sure that the flash mode is supported. *5.everytime starting the camera activity, the battery level is broadcasted, * if meeting the conditions above, forbidden the flash(gray icon), give a dialog to notise user. *6.if the conditions are not satisfied when started, play for a moment, in the camera acitvity * or video camera activity, the conditiosn are satisfied, forbidden the flash and give a notice dialog. *7.the dialog is only given once for each camera activity starting. * *by fuqiang. */ else if(Level < 16) { //close the flash mode. /* if (mIsLowBatteryDialogShown == false) { mRotateDialog.showAlertDialog( getString(R.string.warning), getString(R.string.low_battery_15), null, null, getString(R.string.close), null); mIsLowBatteryDialogShown = true; } */ } } } }; 16、（可选：） R:\wyb\ap6212a0_a33_sc3817r\lichee\tools\pack\chips\sun8iw5p1\configs\default\env.cfg bootdelay=3 loglevel=8 17、 R:\wyb\ap6212a0_a33_sc3817r\lichee\tools\pack\chips\sun8iw5p1\configs\y3\sys_config.fex [power_sply] dcdc1_vol = 3000 dcdc2_vol = 1100 dcdc3_vol = 1200 dcdc4_vol = 0 dcdc5_vol = 1500 aldo1_vol = 3300 aldo2_vol = 2500 aldo3_vol = 3000 dldo1_vol = 3300 dldo2_vol = 3300 dldo3_vol = 2800 ;gpio0_vol = 2800 ldoio0_vol = 2800 ;---------------------------------------------------------------------------------- ;uart configuration ;uart_used = uart x enable ;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function ;---------------------------------------------------------------------------------- [uart0] uart_used = 1 uart_port = 0 uart_type = 2 uart_tx = port:PF02 uart_rx = port:PF04 [uart1] uart_used = 1 uart_port = 1 uart_type = 4 uart_tx = port:PG06 uart_rx = port:PG07 uart_rts = port:PG08 uart_cts = port:PG09 [uart2] uart_used = 1 uart_type = 4 uart_tx = port:PB00 uart_rx = port:PB01 uart_rts = port:PB02 uart_cts = port:PB03 [uart3] uart_used = 0 uart_type = 4 uart_tx = port:PH06 uart_rx = port:PH07 uart_rts = port:PH08 uart_cts = port:PH09 [uart4] uart_used = 0 uart_port = 4 uart_type = 2 uart_tx = port:PA04 uart_rx = port:PA05 uart_rts = port:PA06 uart_cts = port:PA07 ;---------------------------------------------------------------------------------- ;capacitor tp configuration ;ctp_twi_id : twi controller ID ;ctp_twi_addr : I2C slave address, 7bit ;ctp_screen_max_x/_y : resolution of touch panel ;ctp_revert_x/_y_flag : whether need to revert x/y ;ctp_exchange_x_y_flag: whether need to exchange the value of x and y ;ctp_int_port : port for tp's interrupt signal ;ctp_wakeup : port for wakeup tp ;---------------------------------------------------------------------------------- [ctp_para] ctp_used = 1 ctp_name = "gt82x" ctp_twi_id = 0 ctp_twi_addr = 0x5d ctp_screen_max_x = 1280 ctp_screen_max_y = 800 ctp_revert_x_flag = 1 ctp_revert_y_flag = 1 ctp_exchange_x_y_flag = 1 ctp_int_port = port:PL04 ctp_wakeup = port:PL03 ctp_power_ldo = ctp_power_ldo_vol = ctp_power_io = ;-------------------------------------------------------------------------------- ; CTP automatic detection configuration ;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused ;Module name postposition 1 said detection, 0 means no detection. ;-------------------------------------------------------------------------------- [ctp_list_para] ctp_det_used = 1 ft5x_ts = 1 gt82x = 1 gslX680 = 1 gslX680new = 0 gt9xx_ts = 1 gt9xxf_ts = 0 tu_ts = 0 gt818_ts = 1 zet622x = 1 aw5306_ts = 1 icn83xx_ts = 0 [lcd0_para] lcd_used = 1 lcd_driver_name = "default_lcd" lcd_if = 3 lcd_x = 1280 lcd_y = 800 lcd_width = 150 lcd_height = 94 lcd_dclk_freq = 71 lcd_pwm_used = 1 lcd_pwm_ch = 0 lcd_pwm_freq = 50000 lcd_pwm_pol = 1 lcd_hbp = 20 lcd_ht = 1418 lcd_hspw = 10 lcd_vbp = 10 lcd_vt = 830 lcd_vspw = 5 lcd_lvds_if = 0 lcd_lvds_colordepth = 1 lcd_lvds_mode = 0 lcd_frm = 1 lcd_gamma_en = 0 lcd_bright_curve_en = 0 lcd_cmap_en = 0 deu_mode = 0 lcdgamma4iep = 22 smart_color = 90 lcd_bl_en = port:PD13 ;ap6xxx_wl_regon = port:PL06 ;lcd_bl_en = port:PL06 lcd_power = "axp22_dc1sw" lcdd0 = port:PD18 lcdd1 = port:PD19 lcdd2 = port:PD20 lcdd3 = port:PD21 lcdd4 = port:PD22 lcdd5 = port:PD23 lcdd6 = port:PD24 lcdd7 = port:PD25 lcdd8 = port:PD26 lcdd9 = port:PD27 ;---------------------------------------------------------------------------------- ;pwm config ;---------------------------------------------------------------------------------- [pwm0_para] pwm_used = 0 pwm_positive = port:PH00 [pwm1_para] pwm_used = 1 pwm_positive = port:PH01 ;-------------------------------------------------------------------------------- ;wifi configuration ;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3 ;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2 ;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0) ;wifi_mod_sel: 0- none, 1- ap6181, 2- ap6210(wifi+bt), ; 3 - rtl8188eu, 4- rtl8723au(wifi+bt), ; 5 - rtl8723bs, 6- esp8089 ;-------------------------------------------------------------------------------- [wifi_para] wifi_used = 1 wifi_sdc_id = 1 wifi_usbc_id = 1 wifi_usbc_type = 1 wifi_mod_sel = 2 wifi_power = "axp22_dldo1" wifi_power_ext1 = "axp22_dldo2" wifi_power_ext2 = "axp22_aldo1" wifi_power_switch = ;wifi_power_switch = port:power0 ; 1 - ap6181 sdio wifi gpio config ;ap6xxx_wl_regon = port:PL06 ;ap6xxx_wl_host_wake = port:PL07 ;ap6xxx_lpo_use_apclk = 1 ; 2 - ap6210 sdio wifi gpio config ap6xxx_wl_regon = port:PL06 ;ap6xxx_wl_regon = port:PD13 ap6xxx_wl_host_wake = port:PL07 ap6xxx_bt_regon = port:PL08 ap6xxx_bt_wake = port:PL10 ap6xxx_bt_host_wake = port:PL09 ap6xxx_lpo_use_apclk = 1 ; 3 - rtl8188eu usb wifi gpio conifg ; 4 - rtl8723au usb wifi + bt ; 5 - rtl8723bs sdio wifi + bt ;rtl8723bs_chip_en = port:PL11 ;rtl8723bs_wl_regon = port:PL06 ;rtl8723bs_wl_host_wake = port:PL07 ;rtl8723bs_bt_regon = port:PL08 ;rtl8723bs_bt_wake = port:PL10 ;rtl8723bs_bt_host_wake = port:PL09 ;rtl8723bs_lpo_use_apclk = 0 ; 6 - eagle sdio wifi ;esp_wl_chip_en = port:PL03 ;esp_wl_rst = port:PL02 ;-------------------------------------------------------------------------------- ;blue tooth ;bt_used ---- blue tooth used (0- no used, 1- used) ;bt_uard_id ---- uart index ;-------------------------------------------------------------------------------- [bt_para] bt_used = 1 bt_uart_id = 1 power_start = 3 pmu_temp_enable = 0 18、 刷机之后，BT可以用。 传输4.5MB的JPG图片大概需要2分钟。 WIFI： 在设置→WLAN（打开之后）： shell@astar-y3:/ $ shell@astar-y3:/ $ [ 469.609956] init: computing context for service '/system/bin/wpa_supplicant' [ 469.618386] init: starting 'p2p_supplicant' [ 469.625739] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 469.673379] init: waitpid returned pid 2065, status = 0000ff00 [ 469.679923] init: process 'p2p_supplicant', pid 2065 exited [ 476.197334] sndpcm_unmute,line:1099 [ 451.464755] CPU1: Booted secondary processor [ 478.459403] CPU1: shutdown [ 478.462947] [hotplug]: cpu(0) try to kill cpu(1) [ 478.468478] [hotplug]: cpu1 is killed! . shell@astar-y3:/ $ 分析启动的log： [ 17.526849] gpio ap6xxx_wl_regon set val 1, act val 1 [ 17.632508] [ap6xxx]: sdio wifi power state: on [ 17.637576] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.637751] =========== WLAN placed in POWER ON ======== [ 17.654651] [mmc]: sdc1 card_power_on start... [ 17.659576] [mmc]: sdc1 power_supply is null [ 17.664322] [mmc]: sdc1 card_power_on ok [ 17.680039] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.690275] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.772361] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 17.781309] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 17.789448] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.799714] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.862032] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.872262] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.933953] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 8, RTO !! [ 17.941997] *******************Try sdio******************* [ 17.948400] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.958630] [mmc]: mclk 0xf1c2008c 0x8002000e [ 18.027775] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 18.035416] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 18.043087] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 18.051920] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 18.145287] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 18.155436] [mmc]: mclk 0xf1c2008c 0x8002000e [ 18.215346] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 18.225736] [mmc]: mclk 0xf1c2008c 0x8100000b [ 18.285675] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 18.296021] [mmc]: mclk 0xf1c2008c 0x8140030b [ 18.357915] mmc1: new high speed SDIO card at address 0001 [ 18.364532] bcmsdh_register: Linux Kernel SDIO/MMC Driver [ 18.364575] *******************sdio init ok******************* [ 18.377207] bcm_wlan_get_oob_irq enter. [ 18.381537] gpio [359] map to virq [7] ok [ 18.388851] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4 [ 18.396019] dhdsdio_probe_attach: unsupported chip: 0xa9a6 [ 18.402155] dhdsdio_probe: dhdsdio_probe_attach failed [ 18.407899] bcmsdh_probe: device attach failed [ 18.412981] [ 18.412984] Dongle Host Driver, version 1.88.45.3 (r420671) [ 18.412989] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 12:06:39 [ 18.428835] dhd_module_init: sdio_register_driver timeout or error [ 18.435928] gpio ap6xxx_wl_regon set val 0, act val 0 [ 18.541549] [ap6xxx]: sdio wifi power state: off [ 18.546679] =========== WLAN placed in POWER OFF ======== [ 18.546915] mmc1: card 0001 removed [ 18.546995] [mmc]: mmc not poweroff notifiy [ 18.547007] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 18.547160] [mmc]: sdc1 card_power_off start... [ 18.547166] [mmc]: sdc1 power_supply is null [ 18.547173] [mmc]: sdc1 card_power_off ok [ 18.631655] init: command 'insmod' r=-1 [ 18.636066] init: command 'insmod' r=-1 [ 18.658010] fs_mgr: swapon failed for /dev/block/zram0 [ 18.663804] init: command 'swapon_all' r=-1 [ 18.668504] init: processing action 0x58e70 (console_init) [ 18.675396] init: width = 1280 [ 18.678788] init: height = 800 [ 18.682224] init: s.st_size = 3145728 [ 18.686308] init: logo match failed!fbsize = 4096000 [ 18.718811] init: command 'console_init' r=0 [ 18.723628] init: processing action 0x55bf0 (fs) [ 18.730640] init: command 'mkdir' r=-2 [ 18.741901] init: command 'insmod' r=0 [ 18.752227] init: command 'insmod' r=0 [ 18.756491] init: command 'insmod' r=-1 [ 18.771211] init: command 'insmod' r=0 [ 18.779731] init: command 'insmod' r=0 [ 18.791739] init: command 'insmod' r=0 [ 18.803941] init: command 'insmod' r=0 [ 18.816178] init: command 'insmod' r=0 19、查找：（dhdsdio_probe_attach: unsupported chip: 0xa9a6） rootroot@rootroot-E400:~$ cd wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "unsupported chip" . -R ./dhd_sdio.c: DHD_ERROR(("%s: unsupported chip: 0xx\n", ./sbutils.c: SI_ERROR(("sb_chip2numcores: unsupported chip 0x%x\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko 匹配到二进制文件 ./sbutils.o rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ 经过确认： R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd\dhd_sdio.c static bool dhdsdio_probe_attach(struct dhd_bus *bus, osl_t *osh, void *sdh, void *regsva, uint16 devid) { …… bcmsdh_chipinfo(sdh, bus->sih->chip, bus->sih->chiprev); if (!dhdsdio_chipmatch((uint16)bus->sih->chip)) { DHD_ERROR(("%s: unsupported chip: 0xx\n", __FUNCTION__, bus->sih->chip)); goto fail; } …… } 继续追踪： static bool dhdsdio_chipmatch(uint16 chipid) { if (chipid == BCM4325_CHIP_ID) return TRUE; if (chipid == BCM4329_CHIP_ID) return TRUE; if (chipid == BCM4315_CHIP_ID) return TRUE; if (chipid == BCM4319_CHIP_ID) return TRUE; if (chipid == BCM4336_CHIP_ID) return TRUE; if (chipid == BCM4330_CHIP_ID) return TRUE; if (chipid == BCM43237_CHIP_ID) return TRUE; if (chipid == BCM43362_CHIP_ID) return TRUE; if (chipid == BCM4314_CHIP_ID) return TRUE; if (chipid == BCM43242_CHIP_ID) return TRUE; if (chipid == BCM43340_CHIP_ID) return TRUE; if (chipid == BCM43341_CHIP_ID) return TRUE; if (chipid == BCM43143_CHIP_ID) return TRUE; if (chipid == BCM43342_CHIP_ID) return TRUE; if (chipid == BCM4334_CHIP_ID) return TRUE; if (chipid == BCM43239_CHIP_ID) return TRUE; if (chipid == BCM4324_CHIP_ID) return TRUE; if (chipid == BCM4335_CHIP_ID) return TRUE; if (chipid == BCM4339_CHIP_ID) return TRUE; if (chipid == BCM43349_CHIP_ID) return TRUE; if (chipid == BCM4345_CHIP_ID) return TRUE; if (chipid == BCM4350_CHIP_ID) return TRUE; if (chipid == BCM4354_CHIP_ID) return TRUE; if (chipid == BCM4356_CHIP_ID) return TRUE; if (chipid == BCM4358_CHIP_ID) return TRUE; if (chipid == BCM4371_CHIP_ID) return TRUE; if (chipid == BCM43430_CHIP_ID) return TRUE; if (BCM4349_CHIP(chipid)) return TRUE; return FALSE; } 20、 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ll 总用量 40 drwxr-xr-x 7 rootroot rootroot 4096 6月 26 12:02 ./ drwx------ 6 rootroot rootroot 4096 6月 26 14:16 ../ drwxr-xr-x 10 rootroot rootroot 4096 9月 4 2014 brandy/ -rw-rw-r-- 1 rootroot rootroot 116 6月 26 12:02 .buildconfig drwxr-xr-x 15 rootroot rootroot 4096 9月 4 2014 buildroot/ -r-xr-xr-x 1 rootroot rootroot 55 9月 4 2014 build.sh* drwxr-xr-x 28 rootroot rootroot 4096 6月 26 14:30 linux-3.4/ drwxrwxr-x 3 rootroot rootroot 4096 6月 26 12:02 out/ -r--r--r-- 1 rootroot rootroot 232 9月 4 2014 README drwxr-xr-x 7 rootroot rootroot 4096 6月 7 19:33 tools/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh config Welcome to mkscript setup progress All available chips: 0. sun8iw5p1 Choice: 0 All available platforms: 0. android 1. dragonboard 2. linux Choice: 0 All available kernel: 0. linux-3.4 Choice: 0 All available boards: 0. evb 1. maple 2. redwood 3. y2 4. y3 Choice: 4 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh INFO: ---------------------------------------- INFO: build lichee ... INFO: chip: sun8iw5p1 INFO: platform: android INFO: kernel: linux-3.4 INFO: board: y3 INFO: output: out/sun8iw5p1/android/y3 INFO: ---------------------------------------- INFO: build buildroot ... external toolchain has been installed INFO: build buildroot OK. INFO: build kernel ... INFO: prepare toolchain ... Building kernel CHK include/linux/version.h CHK include/generated/utsrelease.h make[1]: “include/generated/mach-types.h”是最新的。 CALL scripts/checksyscalls.sh CHK include/generated/compile.h CC arch/arm/mach-sunxi/pm/standby/common.o CC arch/arm/mach-sunxi/pm/standby/standby_clock.o CC arch/arm/mach-sunxi/pm/standby/standby_ir.o CC arch/arm/mach-sunxi/pm/standby/standby_key.o CC arch/arm/mach-sunxi/pm/standby/standby_power.o CC arch/arm/mach-sunxi/pm/standby/standby_twi.o CC arch/arm/mach-sunxi/pm/standby/standby_usb.o AS arch/arm/mach-sunxi/pm/standby/standby_delay.o CC arch/arm/mach-sunxi/pm/standby/./arisc/standby_arisc.o CC arch/arm/mach-sunxi/pm/standby/./arisc/arisc_hwmsgbox.o CHK kernel/config_data.h CC arch/arm/mach-sunxi/pm/standby/./arisc/arisc_hwspinlock.o CC arch/arm/mach-sunxi/pm/standby/./arisc/arisc_message_manager.o CC arch/arm/mach-sunxi/pm/standby/./../pm_debug.o CC arch/arm/mach-sunxi/pm/standby/./../mem_timing.o CC arch/arm/mach-sunxi/pm/standby/./../mem_mmu_pc.o AS arch/arm/mach-sunxi/pm/standby/./../mem_mmu_pc_asm.o CC arch/arm/mach-sunxi/pm/standby/./../mem_serial.o CC arch/arm/mach-sunxi/pm/standby/./../mem_printk.o AS arch/arm/mach-sunxi/pm/standby/./../mem_divlib.o CC arch/arm/mach-sunxi/pm/standby/./../mem_divlibc.o CC arch/arm/mach-sunxi/pm/standby/./../mem_int.o CC arch/arm/mach-sunxi/pm/standby/./../mem_tmr.o CC arch/arm/mach-sunxi/pm/standby/./../mem_tmstmp.o CC arch/arm/mach-sunxi/pm/standby/./../mem_clk.o CC arch/arm/mach-sunxi/pm/standby/./../mem_hwspinlock.o CC arch/arm/mach-sunxi/pm/standby/standby.o rm -rf *.o arch/arm/mach-sunxi/pm/standby/../*.o CC arch/arm/mach-sunxi/pm/standby/super/common.o CC arch/arm/mach-sunxi/pm/standby/super/super_twi.o CC [M] drivers/net/wireless/bcmdhd/dhd_sdio.o AS arch/arm/mach-sunxi/pm/standby/super/super_delay.o CC arch/arm/mach-sunxi/pm/standby/super/super_clock.o CC arch/arm/mach-sunxi/pm/standby/super/super_power.o CC arch/arm/mach-sunxi/pm/standby/super/super_cpus.o AS arch/arm/mach-sunxi/pm/standby/super/resume/resume1.o CC arch/arm/mach-sunxi/pm/standby/super/resume/resume_head.o CC arch/arm/mach-sunxi/pm/standby/super/resume/resume1_c_part.o CC arch/arm/mach-sunxi/pm/standby/../pm_debug.o CC arch/arm/mach-sunxi/pm/standby/../mem_timing.o CC arch/arm/mach-sunxi/pm/standby/../mem_mmu_pc.o AS arch/arm/mach-sunxi/pm/standby/../mem_mmu_pc_asm.o CC arch/arm/mach-sunxi/pm/standby/../mem_cpu.o CC arch/arm/mach-sunxi/pm/standby/../mem_serial.o CC arch/arm/mach-sunxi/pm/standby/../mem_printk.o CC [M] drivers/net/wireless/bcmdhd/dhd_cdc.o CC [M] drivers/net/wireless/bcmdhd/bcmsdh_linux.o CC [M] drivers/net/wireless/bcmdhd/dhd_common.o AS arch/arm/mach-sunxi/pm/standby/../mem_divlib.o CC arch/arm/mach-sunxi/pm/standby/../mem_divlibc.o drivers/net/wireless/bcmdhd/dhd_sdio.c: In function ‘dhdsdio_chipmatch’: drivers/net/wireless/bcmdhd/dhd_sdio.c:6936:16: error: ‘BCM43430_CHIP_ID’ undeclared (first use in this function) drivers/net/wireless/bcmdhd/dhd_sdio.c:6936:16: note: each undeclared identifier is reported only once for each function it appears in CC arch/arm/mach-sunxi/pm/standby/../mem_int.o make[4]: *** [drivers/net/wireless/bcmdhd/dhd_sdio.o] 错误 1 make[4]: *** 正在等待未完成的任务.... CC arch/arm/mach-sunxi/pm/standby/../mem_tmr.o CC arch/arm/mach-sunxi/pm/standby/../mem_tmstmp.o CC arch/arm/mach-sunxi/pm/standby/../mem_hwspinlock.o CC arch/arm/mach-sunxi/pm/standby/../mem_clk.o Source file is open Destination file is created. Source file is open Destination file is open. temp value is 400. 0 soure_file size is 9496. destination_file size is 0x2800. check sum generated is 0x68D92007. Everything is ok. rm -rf *.o arch/arm/mach-sunxi/pm/standby/../*.o CC arch/arm/mach-sunxi/pm/mem_mapping.o CC arch/arm/mach-sunxi/pm/mem_divlibc.o CC arch/arm/mach-sunxi/pm/mem_cpu.o AS arch/arm/mach-sunxi/pm/mem_cpu_asm.o AS arch/arm/mach-sunxi/pm/mem_mmu_pc_asm.o CC arch/arm/mach-sunxi/pm/mem_mmu_pc.o CC arch/arm/mach-sunxi/pm/mem_int.o CC arch/arm/mach-sunxi/pm/mem_clk.o CC arch/arm/mach-sunxi/pm/mem_tmr.o CC arch/arm/mach-sunxi/pm/mem_tmstmp.o CC arch/arm/mach-sunxi/pm/mem_twi.o CC arch/arm/mach-sunxi/pm/mem_gpio.o CC arch/arm/mach-sunxi/pm/mem_sram.o CC arch/arm/mach-sunxi/pm/mem_ccu.o CC arch/arm/mach-sunxi/pm/mem_cci400.o CC arch/arm/mach-sunxi/pm/mem_gtbus.o CC arch/arm/mach-sunxi/pm/pm_debug.o CC arch/arm/mach-sunxi/pm/mem_timing.o CC arch/arm/mach-sunxi/pm/mem_hwspinlock.o CC arch/arm/mach-sunxi/pm/pm.o CC arch/arm/mach-sunxi/pm/extended_standby.o CC arch/arm/mach-sunxi/pm/standby/super/super_power.o CC arch/arm/mach-sunxi/pm/standby/super/super_twi.o CC arch/arm/mach-sunxi/pm/standby/super/super_clock.o AS arch/arm/mach-sunxi/pm/standby.o AS arch/arm/mach-sunxi/pm/mem.o LD arch/arm/mach-sunxi/pm/pm_tmp.o LD arch/arm/mach-sunxi/pm/built-in.o LD arch/arm/mach-sunxi/built-in.o make[3]: *** [drivers/net/wireless/bcmdhd] 错误 2 make[2]: *** [drivers/net/wireless] 错误 2 make[1]: *** [drivers/net] 错误 2 make: *** [drivers] 错误 2 ERROR: build kernel Failed rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ 21、（dhdsdio_probe_attach: unsupported chip: 0xa9a6） R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd\include\bcmdevs.h #define BCM4350_CHIP_ID 0x4350 #define BCM43430_CHIP_ID 43430 /* 43430 chipcommon chipid 0xa9a6 */ #define BCM4342_CHIP_ID 4342 可以编译通过了。 （查看属性：） shell@astar-y3:/ $ shell@astar-y3:/ $ cd /system/vendor/modules/ shell@astar-y3:/system/vendor/modules $ ll bcm* -rw-r--r-- root root 26020 2017-06-26 12:46 bcm43438a0.hcd -rw-r--r-- root root 748856 2017-06-26 12:46 bcmdhd.ko shell@astar-y3:/system/vendor/modules $ Microsoft Windows [版本 6.1.7600] 版权所有 (c) 2009 Microsoft Corporation。保留所有权利。 C:\Users\Administrator>cd R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\n et\wireless\bcmdhd C:\Users\Administrator>r: R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd>adb remount * daemon not running. starting it now on port 5037 * * daemon started successfully * remount succeeded R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd> R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd>adb push bcmdhd.ko /system/vendor/modules/ 1677 KB/s (748864 bytes in 0.436s) R:\wyb\ap6212a0_a33_sc3817r\lichee\linux-3.4\drivers\net\wireless\bcmdhd> 继续查看属性： shell@astar-y3:/system/vendor/modules $ ll bcm* -rw-r--r-- root root 26020 2017-06-26 12:46 bcm43438a0.hcd -rw-rw-rw- root root 748864 2017-06-26 14:34 bcmdhd.ko shell@astar-y3:/system/vendor/modules $ shell@astar-y3:/system/vendor/modules $ shell@astar-y3:/system/vendor/modules $ chmod 644 bcmdhd.ko Unable to chmod bcmdhd.ko: Operation not permitted 10|shell@astar-y3:/system/vendor/modules $ （必须在su下才能够修改属性：） shell@astar-y3:/system/vendor/modules $ su shell@astar-y3:/system/vendor/modules # chmod 644 bcmdhd.ko shell@astar-y3:/system/vendor/modules # shell@astar-y3:/system/vendor/modules # sync shell@astar-y3:/system/vendor/modules # reboot 22、 [ 0.658241] [wifi]: select wifi: ap6210 !! [ 0.658587] [ap6xxx]: module power name axp22_dldo1 [ 0.658601] [ap6xxx]: module power ext1 name axp22_dldo2 [ 0.658613] [ap6xxx]: module power ext2 name axp22_aldo1 [ 0.658721] [ap6xxx]: get ap6xxx wifi_power_switch failed [ 0.658731] [ap6xxx]: ap6xxx module power set by axp. [ 0.658930] [ap6xxx]: first time [ 0.659285] [ap6xxx]: regulator on. [ 0.661306] [wifi_pm]: wifi gpio init is OK !! （重启之后，WIFI模块要想办法配置为ap6212，现阶段借用的是AP6210！） [ 8.517657] gpio ap6xxx_wl_regon set val 1, act val 1 [ 8.623325] [ap6xxx]: sdio wifi power state: on [ 8.628389] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.628566] =========== WLAN placed in POWER ON ======== [ 8.645459] [mmc]: sdc1 card_power_on start... [ 8.650397] [mmc]: sdc1 power_supply is null [ 8.655129] [mmc]: sdc1 card_power_on ok [ 8.680031] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.690267] [mmc]: mclk 0xf1c2008c 0x8002000e [ 8.772360] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 8.781316] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 8.789448] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.799684] [mmc]: mclk 0xf1c2008c 0x8002000e [ 8.861971] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.872189] [mmc]: mclk 0xf1c2008c 0x8002000e [ 8.933887] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 8, RTO !! [ 8.941921] *******************Try sdio******************* [ 8.948329] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 8.958545] [mmc]: mclk 0xf1c2008c 0x8002000e [ 9.027690] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 9.035325] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 9.043192] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 9.052046] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 9.145358] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 9.155486] [mmc]: mclk 0xf1c2008c 0x8002000e [ 9.215398] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 9.225785] [mmc]: mclk 0xf1c2008c 0x8100000b [ 9.285721] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 9.296049] [mmc]: mclk 0xf1c2008c 0x8140030b [ 9.357922] mmc1: new high speed SDIO card at address 0001 [ 9.364523] bcmsdh_register: Linux Kernel SDIO/MMC Driver [ 9.364563] *******************sdio init ok******************* [ 9.377203] bcm_wlan_get_oob_irq enter. [ 9.381534] gpio [359] map to virq [7] ok [ 9.388816] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4 [ 9.396740] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 9.404660] dhdsdio_probe: Disable prop_txstatus [ 9.410903] wl_create_event_handler(): thread:wl_event_handler:5d started [ 9.410914] tsk Enter, tsk = 0xddca13d8 [ 9.423788] p2p0: P2P Interface Registered [ 9.428464] dhd_attach(): thread:dhd_watchdog_thread:5e started [ 9.435144] dhd_attach(): thread:dhd_dpc:5f started [ 9.440653] dhd_attach(): thread:dhd_sysioc:60 started [ 9.447276] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 [ 9.456558] [ 9.456561] Dongle Host Driver, version 1.88.45.3 (r420671) [ 9.456565] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 14:34:04 [ 9.472427] gpio ap6xxx_wl_regon set val 0, act val 0 [ 9.578054] [ap6xxx]: sdio wifi power state: off [ 9.583186] =========== WLAN placed in RESET ======== （WIFI启动加载正常） shell@astar-y3:/ $ lsmod gt82x 9849 0 - Live 0x00000000 sunxi_schw 12559 0 - Live 0x00000000 (O) cdc_ether 5099 0 - Live 0x00000000 rtl8150 9023 0 - Live 0x00000000 mcs7830 6292 0 - Live 0x00000000 qf9700 7805 0 - Live 0x00000000 asix 17150 0 - Live 0x00000000 usbnet 17700 4 cdc_ether,mcs7830,qf9700,asix, Live 0x00000000 sunxi_keyboard 3021 0 - Live 0x00000000 sw_device 13604 0 - Live 0x00000000 vfe_v4l2 445364 0 - Live 0x00000000 gc2035 12696 0 - Live 0x00000000 gc0308 10702 0 - Live 0x00000000 vfe_subdev 4523 3 vfe_v4l2,gc2035,gc0308, Live 0x00000000 vfe_os 4099 2 vfe_v4l2,vfe_subdev, Live 0x00000000 cci 21594 2 gc2035,gc0308, Live 0x00000000 videobuf_dma_contig 5535 1 vfe_v4l2, Live 0x00000000 videobuf_core 16520 2 vfe_v4l2,videobuf_dma_contig, Live 0x00000000 bcmdhd 556965 0 - Live 0x00000000 leds_sunxi 1351 0 - Live 0x00000000 mali 209914 20 - Live 0x00000000 (O) lcd 38180 0 - Live 0x00000000 disp 993096 8 mali,lcd, Live 0x00000000 nand 280622 0 - Live 0x00000000 (O) shell@astar-y3:/ $ （bcmdhd.ko这个驱动模块加载正常：） （BT没有打开，但是不停地打印BT超时出错，不知道是何解？） shell@astar-y3:/ $ [ 511.880344] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [ 511.887326] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle 23、 由于此时WIFI出于记住上一次的状态的状态（打不开），所以需要重新刷镜像IMG，然后替换：bcmdhd.ko shell@astar-y3:/ $ shell@astar-y3:/ $ lsmod gt82x 9849 0 - Live 0x00000000 sunxi_schw 12559 0 - Live 0x00000000 (O) cdc_ether 5099 0 - Live 0x00000000 rtl8150 9023 0 - Live 0x00000000 mcs7830 6292 0 - Live 0x00000000 qf9700 7805 0 - Live 0x00000000 asix 17150 0 - Live 0x00000000 usbnet 17700 4 cdc_ether,mcs7830,qf9700,asix, Live 0x00000000 sunxi_keyboard 3021 0 - Live 0x00000000 sw_device 13604 0 - Live 0x00000000 vfe_v4l2 445364 0 - Live 0x00000000 gc2035 12696 0 - Live 0x00000000 gc0308 10702 0 - Live 0x00000000 vfe_subdev 4523 3 vfe_v4l2,gc2035,gc0308, Live 0x00000000 vfe_os 4099 2 vfe_v4l2,vfe_subdev, Live 0x00000000 cci 21594 2 gc2035,gc0308, Live 0x00000000 videobuf_dma_contig 5535 1 vfe_v4l2, Live 0x00000000 videobuf_core 16520 2 vfe_v4l2,videobuf_dma_contig, Live 0x00000000 bcmdhd 556965 0 - Live 0x00000000 leds_sunxi 1351 0 - Live 0x00000000 mali 209914 15 - Live 0x00000000 (O) lcd 38180 0 - Live 0x00000000 disp 993096 8 mali,lcd, Live 0x00000000 nand 280622 0 - Live 0x00000000 (O) shell@astar-y3:/ $ shell@astar-y3:/ $ shell@astar-y3:/ $ [ 110.012176] init: computing context for service '/system/bin/wpa_supplicant' [ 110.025400] init: starting 'p2p_supplicant' [ 110.039886] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 110.119751] dhd_conf_set_fw_name_by_chip: firmware_path=/system/vendor/modules/fw_bcm43438a0.bin [ 110.140144] [ 110.140153] Dongle Host Driver, version 1.88.45.3 (r420671) [ 110.140158] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 14:34:04 [ 110.173523] wl_android_wifi_on in 1 [ 110.177409] wl_android_wifi_on in 2: g_wifi_on=0 [ 110.200103] gpio ap6xxx_wl_regon set val 1, act val 1 [ 110.280025] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [ 110.286694] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle [ 110.355684] [ap6xxx]: sdio wifi power state: on [ 110.360930] =========== WLAN going back to live ======== [ 110.366925] sdio_reset_comm(): [ 110.370346] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.380773] [mmc]: mclk 0xf1c2008c 0x8140030b [ 110.443029] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.454758] [mmc]: mclk 0xf1c2008c 0x8140030b [ 110.516097] [mmc]: sdc1 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.530958] [mmc]: mclk 0xf1c2008c 0x80430309 [ 110.592013] [mmc]: sdc1 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.603518] [mmc]: mclk 0xf1c2008c 0x80030009 [ 110.681418] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 110.690726] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 110.700331] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 110.712218] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 110.894520] [mmc]: sdc1 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.904933] [mmc]: mclk 0xf1c2008c 0x80030009 [ 110.964907] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 110.975514] [mmc]: mclk 0xf1c2008c 0x8100000b [ 111.035618] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 111.046398] [mmc]: mclk 0xf1c2008c 0x8140030b [ 111.108547] [ 111.108566] [ 111.108579] dhd_bus_devreset: == WLAN ON == [ 111.116882] dhd_bus_devreset called when dongle is not in reset [ 111.123683] Will call dhd_bus_start instead [ 111.128637] dhd_conf_set_fw_name_by_chip: firmware_path=/system/vendor/modules/fw_bcm43438a0.bin [ 111.140963] dhd_conf_download_config: Ignore config file /system/vendor/modules/config.txt [ 111.151802] Final fw_path=/system/vendor/modules/fw_bcm43438a0.bin [ 111.158689] Final nv_path=/system/vendor/modules/nvram_ap6210.txt [ 111.165542] Final conf_path=/system/vendor/modules/config.txt [ 111.257577] dhdsdio_download_nvram: Open nvram file failed /system/vendor/modules/nvram_ap6210.txt [ 111.268309] _dhdsdio_download_firmware: dongle nvram file download failed [ 111.276022] dhd_bus_start: dhdsdio_probe_download failed. firmware = /system/vendor/modules/fw_bcm43438a0.bin nvram = /system/vendor/modules/nvram_ap6210.txt config = /system/vendor/modules/config.txt [ 111.295979] dhd_bus_devreset: dhd_bus_start fail with -1 [ 111.304154] dhd_dev_reset: dhd_bus_devreset: -1 [ 111.309190] dhd_prot_ioctl : bus is down. we have nothing to do [ 111.330328] dhd_bus_devreset: WLAN OFF DONE [ 111.335225] gpio ap6xxx_wl_regon set val 0, act val 0 [ 111.472499] [ap6xxx]: sdio wifi power state: off [ 111.477661] =========== WLAN placed in RESET ======== [ 111.483304] wl_android_wifi_on: Failed [ 111.487473] wl_android_wifi_off in 1 [ 111.491478] wl_android_wifi_off in 2: g_wifi_on=0 [ 111.496711] wl_android_wifi_off out [ 111.509335] init: waitpid returned pid 1211, status = 0000ff00 [ 111.516072] init: process 'p2p_supplicant', pid 1211 exited shell@astar-y3:/ $ shell@astar-y3:/ $ 24、定位问题：dhd_bus_devreset: dhd_bus_start fail with -1 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "dhd_bus_start fail with" . -R ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "dhd_bus_start fail with" . -R ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ int dhd_bus_devreset(dhd_pub_t *dhdp, uint8 flag) { …… dhd_conf_set_fw_name_by_chip(dhdp, fw_path, firmware_path); if ((bcmerror = dhd_bus_start(dhdp)) != 0) DHD_ERROR(("%s: dhd_bus_start fail with %d\n", __FUNCTION__, bcmerror)); } } return bcmerror; } rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep dhd_bus_start . -R ./dhd_sdio.c: if ((ret = dhd_bus_start(bus->dhd)) != 0) { ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__)); ./dhd_sdio.c: DHD_ERROR(("Will call dhd_bus_start instead\n")); ./dhd_sdio.c: if ((bcmerror = dhd_bus_start(dhdp)) != 0) ./dhd_sdio.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", ./dhd_sdio - 副本.c: if ((ret = dhd_bus_start(bus->dhd)) != 0) { ./dhd_sdio - 副本.c: DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__)); ./dhd_sdio - 副本.c: DHD_ERROR(("Will call dhd_bus_start instead\n")); ./dhd_sdio - 副本.c: if ((bcmerror = dhd_bus_start(dhdp)) != 0) ./dhd_sdio - 副本.c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", ./dhd_sdio - 副本 (2).c: if ((ret = dhd_bus_start(bus->dhd)) != 0) { ./dhd_sdio - 副本 (2).c: DHD_ERROR(("%s: dhd_bus_start failed\n", __FUNCTION__)); ./dhd_sdio - 副本 (2).c: DHD_ERROR(("Will call dhd_bus_start instead\n")); ./dhd_sdio - 副本 (2).c: if ((bcmerror = dhd_bus_start(dhdp)) != 0) ./dhd_sdio - 副本 (2).c: DHD_ERROR(("%s: dhd_bus_start fail with %d\n", ./dhd.h:extern int dhd_bus_start(dhd_pub_t *dhdp); ./wl_android.c:/* Initialize g_wifi_on to 1 so dhd_bus_start will be called for the first ./dhd_linux.c: if ((ret = dhd_bus_start(&dhd->pub)) != 0) { ./dhd_linux.c: /* dhd_prot_init has been called in dhd_bus_start or wl_android_wifi_on */ ./dhd_linux.c:dhd_bus_start(dhd_pub_t *dhdp) rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ 定位到这里： int dhd_bus_start(dhd_pub_t *dhdp) { …… /* try to download image and nvram to the dongle */ if ((dhd->pub.busstate == DHD_BUS_DOWN) && (fw_path[0] != '\0') && (nv_path[0] != '\0')) { #ifdef SHOW_NVRAM_TYPE { /* Show nvram type in the kernel log */ int i; for (i = 0; nv_path[i] != '\0'; ++i) { if (nv_path[i] == '.') { ++i; break; } } DHD_ERROR(("%s: nvram_type = [%s]\n", __FUNCTION__, &nv_path[i])); } #endif /* SHOW_NVRAM_TYPE */ /* wake lock moved to dhdsdio_download_firmware */ if (!(dhd_bus_download_firmware(dhd->pub.bus, dhd->pub.osh, fw_path, nv_path, conf_path))) { DHD_ERROR(("%s: dhdsdio_probe_download failed. firmware = %s nvram = %s config = %s\n", __FUNCTION__, fw_path, nv_path, conf_path)); #ifdef DHDTHREAD if (dhd->threads_only) dhd_os_sdunlock(dhdp); #endif /* DHDTHREAD */ // 2017/6/23 18:40 wenyuanbo download ap6212 fail not return error!!!! //return -1; } } …… return 0; } 由于ap6212没有config.txt文件，下载肯定会出错，比对全志R16平台去AP6212的处理，关闭这里： //return -1; 25、 shell@astar-y3:/ $ shell@astar-y3:/ $ [ 110.012176] init: computing context for service '/system/bin/wpa_supplicant' [ 110.025400] init: starting 'p2p_supplicant' [ 110.039886] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 110.119751] dhd_conf_set_fw_name_by_chip: firmware_path=/system/vendor/modules/fw_bcm43438a0.bin [ 110.140144] [ 110.140153] Dongle Host Driver, version 1.88.45.3 (r420671) [ 110.140158] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 14:34:04 [ 110.173523] wl_android_wifi_on in 1 [ 110.177409] wl_android_wifi_on in 2: g_wifi_on=0 [ 110.200103] gpio ap6xxx_wl_regon set val 1, act val 1 [ 110.280025] [BT_LPM] bluesleep_tx_timer_expire: Tx timer expired [ 110.286694] [BT_LPM] bluesleep_tx_timer_expire: Tx has been idle [ 110.355684] [ap6xxx]: sdio wifi power state: on [ 110.3
7z

ap6212a0_bb16v3_sina33验证通过BT的功能_wifi部分有问题_20170626_1148没有外层目录.7z

R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\overlay\frameworks\base\core\res\res\values\config.xml <!-- List of regexpressions describing the interface (if any) that represent ...
rar

A33芯片资料.rar_A33是什么芯片_A33芯片_全志a33芯片_全志a33资料

全志A33芯片是一款基于ARM Cortex-A7架构的低功耗、高性能的应用处理器，主要应用于入门级平板电脑、智能电视盒以及物联网设备等领域。这款芯片由全志科技（Allwinner Technology）研发，旨在为中低端市场提供性价比...
zip

A33软件开发文档.zip_A33_A33软件资料_全志_全志 a33_全志开发工具

这里是全部的全志A33的软件开发文档，希望对大家有用。
rar

A33_COREBOARD.rar_A33 core_SCH PCB_全志_全志 a33_全志A33 PCB

全志A33是一款基于ARM Cortex-A7架构的低功耗、高性能应用处理器，主要针对入门级平板电脑和智能电视盒子等嵌入式设备。在深入理解全志A33核心板之前，我们需要先了解一些基本概念。 1. **Cortex-A7架构**：Cortex-...
gz

sun8iw5p1.tar.gz_A33_allwinner_allwinner r16_sun8i cpu_全志A33

此代码为全志R16(A33)平台，nand驱动的代码，R16源码在init.rc阶段支持nand模块加载，但需要把生成的nand.ko放入ramdisk.img中，并且能调用insmod命令插入nand模块，这样才可正常启动。
pdf

DragonBoard生产测试配置A20_A31_A31S_A33.pdf

### DragonBoard生产测试配置A20_A31_A31S_A33.pdf 知识点解析 #### 一、DragonBoard概述与测试系统简介 **DragonBoard**是一款专为A20、A31、A31S、A33系列硬件平台设计的测试系统，主要用于自动化和手动测试板卡...
img

福途PAIUI_A33_8423_mk3_sk_tugou_20160331_8G_BOE_GD96-win8内存.img

福途PAIUI_A33_8423_mk3_sk_tugou_20160331_8G_BOE_GD96-win8内存
rar

20161222_a33-6.0-xr819移植包.rar_WIFI IC XR819_softwinner刷机包_xr819

android平台_xr819驱动移植文档-及源码
7z

hm1375_sc3817r_sina33_rtl8188eu服务器验证通过20170621_1021没有外层目录.7z

Q:\a33\hm1375_sc3817r_sina33_rtl8188eu\android\device\softwinner\astar-y3\configs\camera.cfg used_preview_size = 1 key_support_preview_size = 1280x1024, 1280x720, 640x480 key_default_preview_size = ...
7z

8188eu_sc3817r_sina33服务器验证通过_带rtl8188eu的驱动程序_20170619_1108没有外层目录.7z

W:\a33\rtl8188eu_sc3817r_sina33\android\device\softwinner\astar-y3\overlay\frameworks\base\core\res\res\values\config.xml （干掉BT部分） <!-- List of regexpressions describing the interface (if any) ...
zip

趴站蹲点\LiQiDiS_2.71a33.zip

标题中的“趴站蹲点”可能是指一种网络监控或数据抓取的方法，而“LiQiDiS_2.71a33.zip”是一个压缩包文件，其中包含了名为“LiQiDiS_2.71a33”的软件或工具。这个版本号“2.71a33”表明这是一个软件的特定版本，...
zip

a33_android_device_astar:Allwinner A33的Android设备目录（代号astar）

"a33_android_device_astar"是针对Allwinner A33芯片组的一个Android设备目录，它在Android源码树中的位置通常是device/allwinner/a33_astar。Allwinner A33是一款低功耗、低成本的四核ARM Cortex-A7处理器，常见...
zip

a33_lichee_tools:来自全志 A33 SDK 的工具目录

全志A33 SDK中的a33_lichee_tools是一个重要的开发工具集，主要用于在基于全志A33处理器的嵌入式系统上进行软件开发和调试工作。全志A33是一款低功耗、高性能的ARM Cortex-A7四核处理器，广泛应用于平板电脑、智能...
zip

a33_linux:全志 A33 的 Linux 内核 3.4

全志A33是一款基于ARM Cortex-A7架构的四核处理器，主要应用于低成本、低功耗的平板电脑和智能设备。Linux内核3.4是针对全志A33优化的一个版本，它提供了对硬件的良好支持，包括CPU调度、内存管理、中断处理以及设备...
pdf

A33_Vstar_Linux_SDK开发手册

### A33_Vstar_Linux_SDK开发手册知识点详解 #### 一、概述 **A33_Vstar_Linux_SDK开发手册**是深圳市锐尔威视科技有限公司提供的针对A33平台的Linux SDK开发指南，旨在帮助开发者理解并掌握基于A33硬件平台的...
zip

springboot167基于springboot的医院后台管理系统的设计与实现.zip

springboot167基于springboot的医院后台管理系统的设计与实现，含有完整的源码和报告文档

大家在看

recommend-type

SHIMAX_MAC3&MAC50通讯手册

日本SHIMAX_MAC3&MAC50通讯手册
recommend-type

计算机领域EI和SCI收录期刊、影响因子及国际会议

计算机领域EI和SCI收录期刊、影响因子及国际会议，文档中列出了计算机领域（无线通讯、微处理器、生物信息、数据无、数据挖掘和机器学习等）所有Rank1和Rank2级别的国际会议，网上给的资料一般都不全，好不容易找到，给大家分享一下，绝对值得下载！
recommend-type

Petalinux_config配置信息大全（非常重要）.docx

ZYNQ Petalinux_config配置信息大全
recommend-type

一种应用于AMOLED的阵列扫描控制电路 (2011年)

为了提高显示屏的成品率，降低成本，提出了AMOLED屏上行驱动电路的一种设计方案，以PMOS-TFT为行驱动电路的结构。该电路由阵列扫描控制电路构成，每个阵列扫描控制单元由2个时钟信号控制，并包含5个PMOS-TFT。通过 HSPICE的仿真，结果得出电路的仿真结果与分析结果一致，验证了电路功能的正确性。
recommend-type

ARINC664协议 EDE描述

ARINC664协议

最新推荐

recommend-type

springboot167基于springboot的医院后台管理系统的设计与实现.zip

springboot167基于springboot的医院后台管理系统的设计与实现，含有完整的源码和报告文档
recommend-type

macOS 10.9至10.13版高通RTL88xx USB驱动下载

资源摘要信息:"USB_RTL88xx_macOS_10.9_10.13_driver.zip是一个为macOS系统版本10.9至10.13提供的高通USB设备驱动压缩包。这个驱动文件是针对特定的高通RTL88xx系列USB无线网卡和相关设备的，使其能够在苹果的macOS操作系统上正常工作。通过这个驱动，用户可以充分利用他们的RTL88xx系列设备，包括但不限于USB无线网卡、USB蓝牙设备等，从而实现在macOS系统上的无线网络连接、数据传输和其他相关功能。 高通RTL88xx系列是广泛应用于个人电脑、笔记本、平板和手机等设备的无线通信组件，支持IEEE 802.11 a/b/g/n/ac等多种无线网络标准，为用户提供了高速稳定的无线网络连接。然而，为了在不同的操作系统上发挥其性能，通常需要安装相应的驱动程序。特别是在macOS系统上，由于操作系统的特殊性，不同版本的系统对硬件的支持和驱动的兼容性都有不同的要求。 这个压缩包中的驱动文件是特别为macOS 10.9至10.13版本设计的。这意味着如果你正在使用的macOS版本在这个范围内，你可以下载并解压这个压缩包，然后按照说明安装驱动程序。安装过程通常涉及运行一个安装脚本或应用程序，或者可能需要手动复制特定文件到系统目录中。 请注意，在安装任何第三方驱动程序之前，应确保从可信赖的来源获取。安装非官方或未经认证的驱动程序可能会导致系统不稳定、安全风险，甚至可能违反操作系统的使用条款。此外，在安装前还应该查看是否有适用于你设备的更新驱动版本，并考虑备份系统或创建恢复点，以防安装过程中出现问题。 在标签"凄 凄 切 切 群"中，由于它们似乎是无意义的汉字组合，并没有提供有关该驱动程序的具体信息。如果这是一组随机的汉字，那可能是压缩包文件名的一部分，或者可能是文件在上传或处理过程中产生的错误。因此，这些标签本身并不提供与驱动程序相关的任何技术性知识点。 总结来说，USB_RTL88xx_macOS_10.9_10.13_driver.zip包含了用于特定高通RTL88xx系列USB设备的驱动，适用于macOS 10.9至10.13版本的操作系统。在安装驱动之前，应确保来源的可靠性，并做好必要的系统备份，以防止潜在的系统问题。"
recommend-type

PyCharm开发者必备：提升效率的Python环境管理秘籍

# 摘要 本文系统地介绍了PyCharm集成开发环境的搭建、配置及高级使用技巧，重点探讨了如何通过PyCharm进行高效的项目管理和团队协作。文章详细阐述了PyCharm项目结构的优化方法，包括虚拟环境的有效利用和项目依赖的管理。同时，本文也深入分析了版本控制的集成流程，如Git和GitHub的集成，分支管理和代码合并策略。为了提高代码质量，本文提供了配置和使用linters以及代码风格和格式化工具的指导。此外，本文还探讨了PyCharm的调试与性能分析工具，插件生态系统，以及定制化开发环境的技巧。在团队协作方面，本文讲述了如何在PyCharm中实现持续集成和部署（CI/CD）、代码审查，以及
recommend-type

matlab中VBA指令集

MATLAB是一种强大的数值计算和图形处理软件，主要用于科学计算、工程分析和技术应用。虽然它本身并不是基于Visual Basic (VB)的，但在MATLAB环境中可以利用一种称为“工具箱”（Toolbox）的功能，其中包括了名为“Visual Basic for Applications”(VBA)的接口，允许用户通过编写VB代码扩展MATLAB的功能。 MATLAB的VBA指令集实际上主要是用于操作MATLAB的工作空间（Workspace）、图形界面（GUIs）以及调用MATLAB函数。VBA代码可以在MATLAB环境下运行，执行的任务可能包括但不限于： 1. 创建和修改变量、矩阵
recommend-type

在Windows Forms和WPF中实现FontAwesome-4.7.0图形

资源摘要信息: "将FontAwesome470应用于Windows Forms和WPF" 知识点: 1. FontAwesome简介: FontAwesome是一个广泛使用的图标字体库，它提供了一套可定制的图标集合，这些图标可以用于Web、桌面和移动应用的界面设计。FontAwesome 4.7.0是该库的一个版本，它包含了大量常用的图标，用户可以通过简单的CSS类名引用这些图标，而无需下载单独的图标文件。 2. .NET开发中的图形处理: 在.NET开发中，图形处理是一个重要的方面，它涉及到创建、修改、显示和保存图像。Windows Forms和WPF（Windows Presentation Foundation）是两种常见的用于构建.NET桌面应用程序的用户界面框架。Windows Forms相对较为传统，而WPF提供了更为现代和丰富的用户界面设计能力。 3. 将FontAwesome集成到Windows Forms中: 要在Windows Forms应用程序中使用FontAwesome图标，首先需要将FontAwesome字体文件（通常是.ttf或.otf格式）添加到项目资源中。然后，可以通过设置控件的字体属性来使用FontAwesome图标，例如，将按钮的字体设置为FontAwesome，并通过设置其Text属性为相应的FontAwesome类名（如"fa fa-home"）来显示图标。 4. 将FontAwesome集成到WPF中: 在WPF中集成FontAwesome稍微复杂一些，因为WPF对字体文件的支持有所不同。首先需要在项目中添加FontAwesome字体文件，然后通过XAML中的FontFamily属性引用它。WPF提供了一个名为"DrawingImage"的类，可以将图标转换为WPF可识别的ImageSource对象。具体操作是使用"FontIcon"控件，并将FontAwesome类名作为Text属性值来显示图标。 5. FontAwesome字体文件的安装和引用: 安装FontAwesome字体文件到项目中，通常需要先下载FontAwesome字体包，解压缩后会得到包含字体文件的FontAwesome-master文件夹。将这些字体文件添加到Windows Forms或WPF项目资源中，一般需要将字体文件复制到项目的相应目录，例如，对于Windows Forms，可能需要将字体文件放置在与主执行文件相同的目录下，或者将其添加为项目的嵌入资源。 6. 如何使用FontAwesome图标: 在使用FontAwesome图标时，需要注意图标名称的正确性。FontAwesome提供了一个图标检索工具，帮助开发者查找和确认每个图标的确切名称。每个图标都有一个对应的CSS类名，这个类名就是用来在应用程序中引用图标的。 7. 面向不同平台的应用开发: 由于FontAwesome最初是为Web开发设计的，将它集成到桌面应用中需要做一些额外的工作。在不同平台（如Web、Windows、Mac等）之间保持一致的用户体验，对于开发团队来说是一个重要考虑因素。 8. 版权和使用许可: 在使用FontAwesome字体图标时，需要遵守其提供的许可证协议。FontAwesome有多个许可证版本，包括免费的公共许可证和个人许可证。开发者在将FontAwesome集成到项目中时，应确保符合相关的许可要求。 9. 资源文件管理: 在管理包含FontAwesome字体文件的项目时，应当注意字体文件的维护和更新，确保在未来的项目版本中能够继续使用这些图标资源。 10. 其他图标字体库: FontAwesome并不是唯一一个图标字体库，还有其他类似的选择，例如Material Design Icons、Ionicons等。开发人员可以根据项目需求和偏好选择合适的图标库，并学习如何将它们集成到.NET桌面应用中。 以上知识点总结了如何将FontAwesome 4.7.0这一图标字体库应用于.NET开发中的Windows Forms和WPF应用程序，并涉及了相关的图形处理、资源管理和版权知识。通过这些步骤和细节，开发者可以更有效地增强其应用程序的视觉效果和用户体验。
recommend-type

【Postman进阶秘籍】：解锁高级API测试与管理的10大技巧

# 摘要 本文系统地介绍了Postman工具的基础使用方法和高级功能，旨在提高API测试的效率与质量。第一章概述了Postman的基本操作，为读者打下使用基础。第二章深入探讨了Postman的环境变量设置、集合管理以及自动化测试流程，特别强调了测试脚本的编写和持续集成的重要性。第三章介绍了数据驱动测试、高级断言技巧以及性能测试，这些都是提高测试覆盖率和测试准确性的关键技巧。第四章侧重于API的管理，包括版本控制、文档生成和分享，以及监控和报警系统的设计，这些是维护和监控API的关键实践。最后，第五章讨论了Postman如何与DevOps集成以及插件的使用和开发，展示了Postman在更广阔的应
recommend-type

ubuntu22.04怎么恢复出厂设置

### 如何在Ubuntu 22.04上执行恢复出厂设置 #### 清除个人数据并重置系统配置 要使 Ubuntu 22.04 恢复到初始状态，可以考虑清除用户的个人文件以及应用程序的数据。这可以通过删除 `/home` 目录下的所有用户目录来实现，但需要注意的是此操作不可逆，在实际操作前建议先做好重要资料的备份工作[^1]。 对于全局范围内的软件包管理，如果希望移除非官方源安装的应用程序，则可通过 `apt-get autoremove` 命令卸载不再需要依赖项，并手动记录下自定义安装过的第三方应用列表以便后续重新部署环境时作为参考[^3]。 #### 使用Live CD/USB进行修
recommend-type

2001年度广告运作规划：高效利用资源的策略

资源摘要信息:"2001年度广告运作规划" 知识点： 1. 广告运作规划的重要性：广告运作规划是企业营销战略的重要组成部分，它能够帮助企业明确目标、制定计划、优化资源配置，以实现最佳的广告效果和品牌推广。 2. 广告资源的利用：人力、物力、财力和资源是广告运作的主要因素。有效的广告规划需要充分考虑这些因素，以确保广告活动的顺利进行。 3. 广告规划的简洁性：简洁的广告规划更容易理解和执行，可以提高工作效率，减少不必要的浪费。 4. 广告规划的实用性：实用的广告规划能够为企业带来实际的效果，帮助企业提升品牌知名度，增加产品的销售。 5. 广告规划的参考价值：一份好的广告规划可以为其他企业提供参考，帮助企业更好地进行广告运作。 6. 广告规划的下载和分享：互联网为企业提供了方便的广告规划下载和分享平台，企业可以通过网络获取大量的广告规划资料，提高广告工作的效率和质量。 7. 广告规划的持续更新：随着市场环境的变化，广告规划也需要不断更新和完善，以适应新的市场环境。 8. 广告规划的实施：广告规划的成功实施需要团队的协作和执行，需要企业有明确的目标和计划，以及高效的执行力。 9. 广告规划的效果评估：广告规划的实施后，需要对广告效果进行评估，以便了解广告活动的成果，为未来的广告规划提供参考。 10. 广告规划的改进和优化：根据广告效果的评估结果，企业需要对广告规划进行改进和优化，以提高广告活动的效果。
recommend-type

【Postman终极指南】：掌握API测试到自动化部署的全流程

![【Postman终极指南】：掌握API测试到自动化部署的全流程](http://qarocks.ru/wp-content/uploads/2023/11/image-156-1024x538-1.png) # 摘要 本文详细介绍了Postman这一流行的API开发工具，从基础知识讲起，涵盖了API测试、高级测试技术、自动化部署应用，以及企业级应用和最佳实践。在API测试基础和接口测试能力方面，文章探讨了如何构建和管理请求、使用测试脚本以及集合和文件夹的有效使用。高级测试技术部分深入讲述了动态变量、数据驱动测试、监控、测试套件以及集成测试与错误管理。自动化部署章节重点讲解了集合运行器的使
recommend-type

叙述图神经网络领域近年来最新研究进展

### 图神经网络最新研究进展 #### 处理复杂图结构的能力提升 近年来，研究人员致力于提高图神经网络（GNN）处理更复杂的图结构的能力。通过引入多尺度聚合方法和自适应邻接矩阵调整机制，GNN能够在保持计算效率的同时更好地捕捉不同层次的局部特征[^2]。 #### 应用场景扩展至更多领域 除了传统的社交网络分析外，GNN已经被成功应用于多个新兴领域。例如，在医疗健康领域中，基于蛋白质相互作用网络预测药物靶点；在交通流量预测方面，则利用时空图卷积网络来建模城市道路网中的动态变化模式[^3]。 #### 新型架构设计不断涌现 为了克服现有模型存在的局限性并进一步增强表达力，许多创新性的GN