如何测试STM32的RS232与Arduino的RS232通信
时间: 2024-05-21 07:15:51 浏览: 15
测试STM32的RS232与Arduino的RS232通信可以分为以下几个步骤:
1. 确定STM32板子上的RS232串口引脚,一般为TX和RX引脚。
2. 编写STM32的程序,通过串口发送一些数据(如"Hello World"),并配置串口的波特率、数据位、停止位等参数。
3. 连接STM32板子的TX引脚和Arduino板子的RX引脚,同时连接STM32板子的RX引脚和Arduino板子的TX引脚。
4. 确认Arduino板子上的串口波特率、数据位、停止位等参数与STM32板子的程序中设置的参数一致。
5. 在Arduino的程序中读取串口接收到的数据,并进行处理。
6. 运行STM32的程序,观察串口是否成功发送数据并接收到Arduino的回复。
7. 如果测试不成功,可以通过调试STM32的程序和Arduino的程序来找出问题所在。
需要注意的是,不同的STM32板子和Arduino板子可能具有不同的串口引脚和参数设置,因此在测试时需要根据具体的硬件配置进行调整。
相关问题
stm32与arduino串口通信
要实现STM32与Arduino之间的串口通信,需要进行以下步骤:
1.确定串口通信参数:包括波特率、数据位、停止位、奇偶校验位等参数,必须保证两端设置的参数一致。
2.在STM32和Arduino上分别编写串口通信代码,其中包括初始化串口、发送数据和接收数据等操作。
3.在STM32和Arduino之间连接串口通信的引脚,即连接TXD和RXD引脚,注意需要连接两端的引脚一一对应。
4.在Arduino上打开串口监视器,可以实时查看串口通信的数据。
下面是一个简单的实例代码,可以让STM32向Arduino发送数据,并接收Arduino返回的数据:
在STM32上的代码:
```
#include <stdio.h>
#include "stm32f10x.h"
void USART1_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_USART1, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
}
void USART1_SendChar(uint8_t ch)
{
USART_SendData(USART1, ch);
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
}
uint8_t USART1_ReceiveChar(void)
{
while (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET);
return USART_ReceiveData(USART1);
}
int main(void)
{
uint8_t ch;
USART1_Init();
while (1)
{
USART1_SendChar('H');
USART1_SendChar('e');
USART1_SendChar('l');
USART1_SendChar('l');
USART1_SendChar('o');
USART1_SendChar('\r');
USART1_SendChar('\n');
ch = USART1_ReceiveChar();
if (ch != 0)
{
printf("Received char: %c\n", ch);
}
}
}
```
在Arduino上的代码:
```
void setup()
{
Serial.begin(9600);
}
void loop()
{
if (Serial.available() > 0)
{
char ch = Serial.read();
Serial.print("Received char: ");
Serial.println(ch);
}
delay(1000);
Serial.print("Hello world!\n");
}
```
在这个例子中,STM32会向Arduino发送字符串"Hello",并使用printf函数输出接收到的字符;Arduino会不断发送"Hello world!"字符串,并在接收到STM32发送的字符时输出到串口监视器中。
arduino与stm32通信
Arduino与STM32通信可以通过串口通信实现。在Arduino编程语言和开发环境的支持下,可以使用Arduino板上的串口与STM32板进行通信。首先,需要在Arduino IDE中安装STM32的开发环境,然后配置Arduino IDE以支持STM32板。接下来,编写程序代码来实现串口通信。可以选择使用基于标准库函数或基于HAL库函数的编程方式。最后,连接硬件并执行程序,即可实现Arduino与STM32的通信。\[2\]\[3\]
#### 引用[.reference_title]
- *1* [Ardunio IDE完成STM32板子的串口通信](https://blog.csdn.net/qq_45264808/article/details/111039632)[target="_blank" data-report-click={"spm":"1018.2226.3001.9630","extra":{"utm_source":"vip_chatgpt_common_search_pc_result","utm_medium":"distribute.pc_search_result.none-task-cask-2~all~insert_cask~default-1-null.142^v91^insertT0,239^v3^insert_chatgpt"}} ] [.reference_item]
- *2* *3* [Ardunio下STM32板子的串口通信](https://blog.csdn.net/Mirecz/article/details/111111819)[target="_blank" data-report-click={"spm":"1018.2226.3001.9630","extra":{"utm_source":"vip_chatgpt_common_search_pc_result","utm_medium":"distribute.pc_search_result.none-task-cask-2~all~insert_cask~default-1-null.142^v91^insertT0,239^v3^insert_chatgpt"}} ] [.reference_item]
[ .reference_list ]
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)