DHT11如何与stm32进行串口通信
时间: 2024-06-06 16:08:40 浏览: 13
DHT11传感器可以通过单总线协议或者数字串口协议与STM32进行通信。其中,数字串口协议通常使用的是UART(通用异步收发传输)协议。
下面是DHT11与STM32通过UART进行通信的步骤:
1. 配置STM32的串口通信参数,包括波特率、数据位、停止位、校验位等。
2. 将DHT11的输出引脚连接到STM32的串口接收引脚,通常为RXD。
3. 在STM32的程序中编写串口接收函数,用于接收DHT11传感器发送的数据。
4. 在STM32的程序中编写串口发送函数,用于向DHT11传感器发送指令,读取温湿度数据。
5. 在STM32的程序中编写数据处理函数,将接收到的数据进行解析,得到温湿度数据。
6. 在STM32的程序中添加定时器中断,控制读取温湿度数据的时间间隔,以避免过度频繁地读取数据。
需要注意的是,DHT11传感器的数据传输速率较慢,且存在一定的数据丢失率。因此,在编写程序时需要进行一定的异常处理,以确保数据的准确性和可靠性。
相关问题
DHT11怎么与stm32串口通信
DHT11是一种数字温湿度传感器,通常情况下它不需要与STM32进行串口通信。DHT11传感器的数据是通过单总线(OneWire)协议进行传输的,因此只需要将DHT11的数据线连接到STM32的GPIO口,然后通过编程读取GPIO口的电平变化即可获取DHT11传感器的数据。
下面是连接DHT11传感器与STM32的步骤:
1. 将DHT11的VCC引脚连接到STM32的3.3V电源,将GND引脚连接到STM32的地(GND)。
2. 将DHT11的数据线连接到STM32的一个GPIO口,可以选择任意一个GPIO口,但需要在程序中对其进行配置。
3. 在STM32中编写程序,通过GPIO口读取DHT11传感器的数据。可以使用STM32的输入输出库函数,例如GPIO_ReadInputDataBit()函数,来读取GPIO口的电平变化,并解析DHT11传感器的数据。
需要注意的是,在读取DHT11传感器的数据时,需要按照DHT11协议的规定进行操作。具体来说,需要先向DHT11发送起始信号,然后等待DHT11的响应,最后读取DHT11传输的40位数据并进行解析。DHT11传感器的协议细节可以参考其数据手册。
DHT11与stm32f103c8t6引脚串口
DHT11是一种数字温湿度传感器,它与STM32F103C8T6的连接方式可以使用单片机的GPIO口直接连接DHT11的数据引脚,并且可以通过串口输出数据。
以下是连接步骤:
1.将DHT11的VCC引脚连接到STM32F103C8T6的5V引脚。
2.将DHT11的GND引脚连接到STM32F103C8T6的GND引脚。
3.将DHT11的数据引脚连接到STM32F103C8T6的任意一个GPIO口,例如PA0。
4.在单片机程序中,使能对应的GPIO口,并使用相应的库函数读取DHT11的数据。读取过程中,需要注意DHT11的数据通信协议,具体可以参考DHT11的数据手册。
5.通过串口将读取到的温湿度数据输出到PC端,以方便用户查看。
下面是一个简单的示例程序,可供参考:
```c
#include "stm32f10x.h"
#include "stdio.h"
void GPIO_Configuration(void);
void USART_Configuration(void);
void Delay_us(uint32_t us);
void DHT11_Start(void);
uint8_t DHT11_Read_Byte(void);
uint8_t DHT11_Read_Data(uint8_t *temp,uint8_t *humi);
int main(void)
{
uint8_t temp,humi;
char str[100];
GPIO_Configuration();
USART_Configuration();
while (1)
{
if (DHT11_Read_Data(&temp,&humi))
{
sprintf(str,"Temperature is %d'C, Humidity is %d%%\r\n",temp,humi);
USART_SendString(USART1,str);
}
Delay_us(2000000);
}
}
void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_Init(GPIOA, &GPIO_InitStructure);
}
void USART_Configuration(void)
{
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
USART_Cmd(USART1, ENABLE);
}
void Delay_us(uint32_t us)
{
uint32_t i;
for (i = 0; i < us*8; i++);
}
void DHT11_Start(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_SetBits(GPIOA,GPIO_Pin_0);
Delay_us(1000);
GPIO_ResetBits(GPIOA,GPIO_Pin_0);
Delay_us(18000);
GPIO_SetBits(GPIOA,GPIO_Pin_0);
Delay_us(20);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
}
uint8_t DHT11_Read_Byte(void)
{
uint8_t i,dat;
for (i = 0; i < 8; i++)
{
while(GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0) == RESET);
Delay_us(30);
if (GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0) == SET)
{
dat|=0x01<<(7-i);
while(GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0) == SET);
}
else
{
dat&=~(0x01<<(7-i));
}
}
return dat;
}
uint8_t DHT11_Read_Data(uint8_t *temp,uint8_t *humi)
{
uint8_t buf[5],i;
DHT11_Start();
if (GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0) == RESET)
{
while(GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0) == RESET);
while(GPIO_ReadInputDataBit(GPIOA,GPIO_Pin_0) == SET);
for (i = 0; i < 5; i++)
{
buf[i] = DHT11_Read_Byte();
}
if ((buf[0]+buf[1]+buf[2]+buf[3]) == buf[4])
{
*humi = buf[0];
*temp = buf[2];
return 1;
}
}
return 0;
}
void USART_SendString(USART_TypeDef* USARTx, char* str)
{
while (*str)
{
USART_SendData(USARTx, *str++);
while (USART_GetFlagStatus(USARTx, USART_FLAG_TXE) == RESET);
}
}
```
在这个示例程序中,我们使用的是PA0作为DHT11的数据引脚,PA9和PA10作为串口通信口。程序通过DHT11_Read_Data函数读取DHT11的温湿度数据,并通过串口将数据输出到PC端。
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)