esp32-idf sx126x-cad代码
时间: 2023-08-07 22:02:08 浏览: 57
以下是 ESP32 IDF 中使用 SX126x 芯片进行 CAD 操作的示例代码:
```c
#include "sx126x_driver.h"
// 定义 SX126x 设备对象
sx126x_t sx126x_device;
void app_main()
{
// 初始化 SX126x 设备对象
sx126x_init(&sx126x_device);
// 设置 SX126x 工作模式为 CAD
sx126x_set_cad_mode(&sx126x_device);
// 开始 CAD 操作
sx126x_start_cad(&sx126x_device);
// 等待 CAD 操作完成
while (sx126x_get_cad_result(&sx126x_device) == SX126X_CAD_BUSY)
{
vTaskDelay(10 / portTICK_PERIOD_MS);
}
}
```
需要注意的是,以上代码仅为示例代码,不能直接运行。在实际使用中,需要根据具体的硬件和软件环境进行修改。
相关问题
esp32-idf sx1268-cad唤醒代码
以下是使用ESP32 IDF开发的SX1268 LoRa模块唤醒代码示例:
```c
#include "driver/gpio.h"
#include "sx126x.h"
#define PIN_NUM_WAKEUP 23
void sx126x_wakeup()
{
//Configure the wakeup pin as output
gpio_config_t io_conf = {
.pin_bit_mask = (1ULL << PIN_NUM_WAKEUP),
.mode = GPIO_MODE_OUTPUT,
.pull_up_en = GPIO_PULLUP_DISABLE,
.pull_down_en = GPIO_PULLDOWN_DISABLE,
.intr_type = GPIO_INTR_DISABLE
};
gpio_config(&io_conf);
//Send a pulse on the wakeup pin to wake up SX126x
gpio_set_level(PIN_NUM_WAKEUP, 0);
ets_delay_us(200);
gpio_set_level(PIN_NUM_WAKEUP, 1);
ets_delay_us(200);
gpio_set_level(PIN_NUM_WAKEUP, 0);
//Wait for SX126x to wake up
ets_delay_us(5000);
}
int main(void)
{
sx126x_wakeup();
//Rest of the application logic here
return 0;
}
```
在这个示例中,我们使用ESP32的GPIO23引脚作为SX1268的唤醒引脚。我们在唤醒函数中将引脚配置为输出模式,并发送一个脉冲以唤醒SX1268。然后我们等待一段时间,以确保SX1268已经完全唤醒。
请注意,这只是一个示例代码,您需要根据您的实际硬件和应用程序要求进行修改。
esp32-idf sx1268-cad模式代码
以下是使用ESP32 IDF开发的SX1268 LoRa模块模式代码示例:
```c
#include "driver/gpio.h"
#include "sx126x.h"
#define PIN_NUM_MODE 17
void sx126x_set_mode(uint8_t mode)
{
//Configure the mode pin as output
gpio_config_t io_conf = {
.pin_bit_mask = (1ULL << PIN_NUM_MODE),
.mode = GPIO_MODE_OUTPUT,
.pull_up_en = GPIO_PULLUP_DISABLE,
.pull_down_en = GPIO_PULLDOWN_DISABLE,
.intr_type = GPIO_INTR_DISABLE
};
gpio_config(&io_conf);
//Set the mode pin to the desired mode
gpio_set_level(PIN_NUM_MODE, mode);
}
int main(void)
{
sx126x_set_mode(1); //Set SX1268 to LoRa mode
//Rest of the application logic here
return 0;
}
```
在这个示例中,我们使用ESP32的GPIO17引脚来控制SX1268的模式。我们在设置模式函数中将引脚配置为输出模式,并将其设置为所需模式。在这种情况下,我们将SX1268设置为LoRa模式。
请注意,这只是一个示例代码,您需要根据您的实际硬件和应用程序要求进行修改。