arduino nano上传项目出错后,错误信息为:avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x70
时间: 2023-05-25 09:02:46 浏览: 375
这个错误通常是由于以下原因之一造成的:
1. 上传程序时,串口选择错误。请确保使用正确的串口。
2. 上传速度设置错误。请确认串口波特率和上传速度匹配。
3. 引脚设置错误。请确保程序中使用的引脚与实际硬件连接的引脚匹配。
4. 连接问题。检查串口连接和电路连接,确保板子正确连接到计算机。
如果您的上述方法尝试无效,还可以尝试以下几个解决方案:
1. 更换USB电缆。有时,USB电缆可能会导致上传失败。
2. 重启计算机。有时候,计算机可能会出现一些不可预料的问题,重启计算机可能有助于解决问题。
3. 更换Arduino板子。如果所有方法都不能解决问题,那么您可能需要更换您的Arduino板子。
相关问题
arduino出现以下错误:avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00 avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00 上传项目出错
这个错误通常表示Arduino IDE无法连接到Arduino板子。以下是可能的原因和解决方法:
1. 确认您已经选择了正确的板子和端口。在Arduino IDE的“工具”菜单中选择“板子”和“端口”,确保它们与您的Arduino板子匹配。
2. 确认您的Arduino板子已经正确连接到计算机。确保USB线连接良好,以及计算机和Arduino板子之间没有其他设备干扰。
3. 尝试使用其他USB端口或电脑。有时候USB端口或计算机本身可能出现问题。
4. 确认您正在使用正确的引脚。如果您正在使用自定义电路板或把Arduino板子当做与其他设备一起使用的模块,那么请确保您的引脚连接正确。
5. 尝试按下Arduino板子上的重置按钮。在上传代码时,有时候需要重置Arduino板子以确保通信正常。
如果您尝试了以上所有方法,还是无法上传代码,那么您可能需要更换Arduino板子或者检查USB线是否损坏。
arduino nano 报错:avrdude: stk500_recv(): programmer is not responding
这个错误通常是由于连接问题引起的。请检查您的连接,确保您的Arduino Nano与计算机正确连接,并且端口和波特率设置正确。您还可以尝试使用不同的USB端口或更换USB电缆。如果问题仍然存在,请尝试使用不同的编程器或重新烧录引导程序。