stm32f103按键控制LED程序
时间: 2023-08-24 13:05:02 浏览: 87
以下是使用STM32F103控制LED的按键程序示例。该程序通过按下按键来控制LED的亮灭。
首先,需要在STM32F103上配置GPIO引脚,将一个引脚用于LED输出,另一个引脚用于按键输入。例如,LED的输出引脚为PA5,按键的输入引脚为PB12。
接下来,需要使用STM32的中断功能来检测按键的状态变化。在这个示例中,我们使用外部中断EXTI线12来检测PB12引脚的状态变化。当按键被按下时,引脚状态变为低电平,触发中断处理程序。
中断处理程序中,我们将LED引脚的状态取反,以切换LED的亮灭状态。代码如下:
```
#include "stm32f10x.h"
void EXTI15_10_IRQHandler(void) {
if (GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_12) == RESET) {
GPIO_WriteBit(GPIOA, GPIO_Pin_5, (BitAction)(1 - GPIO_ReadOutputDataBit(GPIOA, GPIO_Pin_5)));
}
EXTI_ClearITPendingBit(EXTI_Line12);
}
int main(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
// 使能GPIOA和GPIOB的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB, ENABLE);
// 配置PA5为推挽输出
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置PB12为上拉输入
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_Init(GPIOB, &GPIO_InitStructure);
// 配置外部中断EXTI线12
EXTI_InitStructure.EXTI_Line = EXTI_Line12;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
// 配置中断控制器NVIC
NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x00;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x00;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
while (1) {
// 主循环
}
}
```
在程序中,我们使用了STM32的库函数来简化GPIO和中断的配置过程。在主循环中,我们可以添加其他的功能代码,例如读取传感器数据、控制其他设备等。
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)