生成一段用于STM32F030芯片ADC采集正弦波信号显示频率及幅度

以下是一段用于STM32F030芯片ADC采集正弦波信号显示频率及幅度的代码：

#include "stm32f0xx.h"
#include "stm32f0xx_adc.h"
#include "stm32f0xx_gpio.h"
#include "stm32f0xx_rcc.h"
#include "stm32f0xx_tim.h"

#define ADC1_DR_ADDRESS ((uint32_t)0x40012440)

void GPIO_Configuration(void);
void ADC_Configuration(void);
void TIM_Configuration(void);

uint16_t ADCValue = 0;
uint16_t TIM2Value = 0;
float frequency = 0;
float amplitude = 0;

int main(void)
{
    GPIO_Configuration();
    ADC_Configuration();
    TIM_Configuration();

    while (1)
    {
        ADC_SoftwareStartConv(ADC1);  // 开始一次ADC转换
        while (!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC));  // 等待转换完成
        ADCValue = ADC_GetConversionValue(ADC1);  // 获取转换结果

        TIM2Value = TIM_GetCapture2(TIM2);  // 获取定时器2的CCR2寄存器值
        frequency = 72000000.0 / (TIM2Value * 4.0);  // 计算频率
        amplitude = ADCValue * 3.3 / 4096.0;  // 计算幅度

        delay_ms(100);  // 延迟100ms
    }
}

void GPIO_Configuration(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;

    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
}

void ADC_Configuration(void)
{
    ADC_InitTypeDef ADC_InitStructure;

    RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);

    ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
    ADC_InitStructure.ADC_ScanDirection = ADC_ScanDirection_Upward;
    ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
    ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
    ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T1_CC1;
    ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
    ADC_InitStructure.ADC_NbrOfConversion = 1;
    ADC_Init(ADC1, &ADC_InitStructure);

    ADC_ChannelConfig(ADC1, ADC_Channel_0, ADC_SampleTime_28_5Cycles);

    ADC_Cmd(ADC1, ENABLE);

    while (!ADC_GetFlagStatus(ADC1, ADC_FLAG_ADEN));
}

void TIM_Configuration(void)
{
    TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
    TIM_OCInitTypeDef TIM_OCInitStructure;

    RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);

    TIM_TimeBaseStructure.TIM_Period = 17999;
    TIM_TimeBaseStructure.TIM_Prescaler = 0;
    TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
    TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
    TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);

    TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
    TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
    TIM_OCInitStructure.TIM_Pulse = 9000;
    TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
    TIM_OC2Init(TIM2, &TIM_OCInitStructure);

    TIM_Cmd(TIM2, ENABLE);
}

这段代码使用了ADC1和TIM2模块，通过ADC采集正弦波信号的幅度值，通过TIM2测量正弦波信号的周期，从而计算出信号的频率和幅度。其中，ADC1使用了PA0通道，TIM2使用了PA1通道。通过PWM输出，可以产生正弦波信号。