基于GD32F103RCT6的0.96寸oled显示代码

由于涉及到硬件的具体实现，我无法提供完整的代码。但是，以下是基于GD32F103RCT6的0.96寸oled显示的一些关键步骤和代码示例，供您参考：

1. 配置SPI通信

//配置SPI1
rcu_periph_clock_enable(RCU_GPIOA);
rcu_periph_clock_enable(RCU_SPI1);

gpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_5);//SCK
gpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_7);//MOSI

spi_parameter_struct spi_init_struct;
spi_i2s_parameter_struct spi_i2s_init_struct;

spi_i2s_deinit(SPI1);

spi_init_struct.trans_mode           = SPI_TRANSMODE_FULLDUPLEX;
spi_init_struct.device_mode          = SPI_MASTER;
spi_init_struct.frame_size           = SPI_FRAMESIZE_8BIT;
spi_init_struct.clock_polarity_phase = SPI_CK_PL_HIGH_PH_2EDGE;
spi_init_struct.nss                  = SPI_NSS_SOFT;
spi_init_struct.prescale             = SPI_PSC_2;
spi_init_struct.endian               = SPI_ENDIAN_MSB;

spi_init(SPI1, &spi_init_struct);

spi_i2s_init_struct.i2s_mode            = SPI_I2S_MODE_TX;
spi_i2s_init_struct.i2s_standard        = SPI_I2S_STD_MSB;
spi_i2s_init_struct.data_format        = SPI_I2S_DF_MSB;
spi_i2s_init_struct.i2s_mclk_output     = SPI_I2S_MCLK_OUTPUT_ENABLE;
spi_i2s_init_struct.i2s_audio_freq      = SPI_I2S_AUDIO_FREQ_DEFAULT;
spi_i2s_init_struct.i2s_frame_format    = SPI_I2S_FRAMEFORMAT_MSBJUSTIFIED;
spi_i2s_init_struct.i2s_ws_polarity     = SPI_I2S_WS_POLARITY_HIGH;
spi_i2s_init(SPI1, &spi_i2s_init_struct);

2. 配置OLED显示

#define OLED_CMD  0x00  //写命令
#define OLED_DATA 0x01  //写数据

void OLED_WR_Byte(uint8_t dat,uint8_t cmd)
{
    if(cmd) OLED_DC_Set();
    else    OLED_DC_Reset();
    OLED_CS_Reset();
    spi_i2s_data_transmit(SPI1, dat);
    while (RESET == spi_i2s_flag_get(SPI1, SPI_FLAG_TXE));
    OLED_CS_Set();
}

void OLED_Init(void)
{
    OLED_RST_Reset();
    delay_ms(200);
    OLED_RST_Set();
    delay_ms(200);

    OLED_WR_Byte(0xAE, OLED_CMD); //关闭显示

    OLED_WR_Byte(0xD5, OLED_CMD); //设置时钟分频因子/振荡器频率
    OLED_WR_Byte(0x80, OLED_CMD); //振荡器频率

    OLED_WR_Byte(0xA8, OLED_CMD); //设置驱动路数
    OLED_WR_Byte(0x3F, OLED_CMD); //默认值(1/64)

    OLED_WR_Byte(0xD3, OLED_CMD); //设置显示偏移
    OLED_WR_Byte(0x00, OLED_CMD); //默认值

    OLED_WR_Byte(0x40, OLED_CMD); //设置显示开始行 [5:0]
    OLED_WR_Byte(0xA0, OLED_CMD); //设置段重定义设置,bit0:0,0->0;1,0->127;
                                  //bit1:0,0->0;1,0->63;
                                  //默认：0XA0
    OLED_WR_Byte(0xC0, OLED_CMD); //设置扫描方向;bit0:0,从左往右;1,从右往左
                                  //bit1:0,从上往下;1,从下往上
                                  //默认：0XC0

    OLED_WR_Byte(0xDA, OLED_CMD); //设置COM硬件引脚配置
    OLED_WR_Byte(0x12, OLED_CMD); //默认值(0x12)

    OLED_WR_Byte(0x81, OLED_CMD); //对比度设置
    OLED_WR_Byte(0xCF, OLED_CMD); //1~255;默认：0X7F (亮度设置,越大越亮)

    OLED_WR_Byte(0xD9, OLED_CMD); //设置预充电周期
    OLED_WR_Byte(0xF1, OLED_CMD); //默认值

    OLED_WR_Byte(0xDB, OLED_CMD); //设置VCOMH 电压倍率
    OLED_WR_Byte(0x40, OLED_CMD); //默认值

    OLED_WR_Byte(0xA4, OLED_CMD); //全局显示开启;bit0:1,开启;0,关闭;(白屏/黑屏)
                                  //默认：开启;

    OLED_WR_Byte(0xA6, OLED_CMD); //设置显示方式;bit0:1,反相显示;0,正常显示
                                  //默认：正常显示

    OLED_WR_Byte(0xAF, OLED_CMD); //开启显示
}

3. 显示内容

void OLED_Fill(uint8_t dat)
{
    uint8_t i, j;
    for (i = 0; i < 8; i++)
    {
        OLED_WR_Byte(0xb0 + i, OLED_CMD);
        OLED_WR_Byte(0x00, OLED_CMD);
        OLED_WR_Byte(0x10, OLED_CMD);
        for (j = 0; j < 128; j++)
            OLED_WR_Byte(dat, OLED_DATA);
    }
}

void OLED_ShowStr(uint8_t x,uint8_t y,uint8_t *str)
{
    uint8_t c = 0, i = 0, j = 0;

    while (str[j] != '\0')
    {
        c = str[j] - 32;
        if (x > 128 - 1)
        {
            x = 0;
            y++;
        }
        OLED_Set_Pos(x, y);
        for (i = 0; i < 6; i++)
            OLED_WR_Byte(F6x8[c][i], OLED_DATA);
        x += 6;
        j++;
    }
}

以上是基于GD32F103RCT6的0.96寸oled显示的一些关键步骤和代码示例，希望能帮助到您。