模拟iic读TMP102温度
时间: 2023-07-05 15:08:20 浏览: 53
好的,以下是模拟iic读取TMP102温度的示例代码:
```python
import time
import smbus
# 初始化i2c总线
bus = smbus.SMBus(1)
# TMP102设备地址
address = 0x48
# 温度寄存器地址
temp_reg = 0x00
# 读取温度数据
def read_temp():
# 发送读取温度寄存器地址命令
bus.write_byte(address, temp_reg)
# 读取温度数据
data = bus.read_word_data(address, temp_reg)
# 转换温度数据为实际温度值
temp = (data >> 8) + ((data & 0xff) / 256.0)
# 转换为摄氏度
temp_c = temp * 0.0625
return temp_c
# 循环读取温度并输出
while True:
temp_c = read_temp()
print('当前温度为:%.2f℃' % temp_c)
time.sleep(1)
```
需要注意的是,该代码要求使用树莓派等支持i2c总线的设备,并且需要先安装smbus库。在运行代码前,需要先将TMP102设备连接到i2c总线上。
相关问题
io模拟iic读TMP102温度
以下是基于STM32F4系列单片机的IO模拟IIC读取TMP102温度的示例代码:
```c
#include "stm32f4xx.h"
#define SDA_PIN GPIO_Pin_9
#define SDA_GPIO_PORT GPIOB
#define SDA_GPIO_CLK RCC_AHB1Periph_GPIOB
#define SCL_PIN GPIO_Pin_8
#define SCL_GPIO_PORT GPIOB
#define SCL_GPIO_CLK RCC_AHB1Periph_GPIOB
#define I2C_SPEED 100000
void IIC_Delay(void) {
uint16_t i = 7 * (SystemCoreClock / 10000000);
while(i--);
}
void IIC_Init(void) {
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(SDA_GPIO_CLK | SCL_GPIO_CLK, ENABLE);
GPIO_InitStructure.GPIO_Pin = SDA_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(SDA_GPIO_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = SCL_PIN;
GPIO_Init(SCL_GPIO_PORT, &GPIO_InitStructure);
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
}
void IIC_Start(void) {
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
GPIO_ResetBits(SDA_GPIO_PORT, SDA_PIN);
IIC_Delay();
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
}
void IIC_Stop(void) {
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
GPIO_ResetBits(SDA_GPIO_PORT, SDA_PIN);
IIC_Delay();
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
}
uint8_t IIC_WaitAck(void) {
uint16_t i = 50000;
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
IIC_Delay();
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
while(GPIO_ReadInputDataBit(SDA_GPIO_PORT, SDA_PIN)) {
if(!(i--)) {
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
return 1;
}
}
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
return 0;
}
void IIC_Ack(void) {
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
GPIO_ResetBits(SDA_GPIO_PORT, SDA_PIN);
IIC_Delay();
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
}
void IIC_NAck(void) {
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
IIC_Delay();
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
}
void IIC_WriteByte(uint8_t byte) {
uint8_t i = 8;
while(i--) {
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
if(byte & 0x80)
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
else
GPIO_ResetBits(SDA_GPIO_PORT, SDA_PIN);
byte <<= 1;
IIC_Delay();
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
}
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
}
uint8_t IIC_ReadByte(uint8_t ack) {
uint8_t i = 8, byte = 0;
GPIO_SetBits(SDA_GPIO_PORT, SDA_PIN);
while(i--) {
GPIO_ResetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
byte <<= 1;
if(GPIO_ReadInputDataBit(SDA_GPIO_PORT, SDA_PIN))
byte |= 0x01;
GPIO_SetBits(SCL_GPIO_PORT, SCL_PIN);
IIC_Delay();
}
if(ack)
IIC_Ack();
else
IIC_NAck();
return byte;
}
void TMP102_Init(void) {
IIC_Start();
IIC_WriteByte(0x90);
IIC_WaitAck();
IIC_WriteByte(0x01);
IIC_WaitAck();
IIC_Stop();
}
float TMP102_ReadTemp(void) {
uint16_t temp;
float t;
IIC_Start();
IIC_WriteByte(0x90);
IIC_WaitAck();
IIC_WriteByte(0x00);
IIC_WaitAck();
IIC_Start();
IIC_WriteByte(0x91);
IIC_WaitAck();
temp = (IIC_ReadByte(1) << 8) | IIC_ReadByte(0);
IIC_Stop();
t = temp * 0.0625;
return t;
}
int main(void) {
float temperature;
RCC_DeInit();
SystemInit();
IIC_Init();
TMP102_Init();
while(1) {
temperature = TMP102_ReadTemp();
// 处理温度数据
}
}
```
在本例中,使用GPIO模拟IIC总线,通过模拟SCL和SDA信号来实现与TMP102的通信。首先初始化GPIO口,然后定义IIC总线的各种操作函数。在主函数中初始化TMP102,并循环读取温度数据。需要注意的是,TMP102的温度数据为16位有符号数,需要经过转换才能得到实际温度值。
IO模拟IIC读取TMP275AIDR器件的读取函数怎么写,请写出代码
好的,以下是模拟 IIC 读取 TMP275AIDR 器件的读取函数的示例代码:
```c
#include "stm32f10x.h"
#define SDA_OUT() GPIO_InitTypeDef GPIO_InitStructure; \
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7; \
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; \
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; \
GPIO_Init(GPIOB, &GPIO_InitStructure)
#define SDA_IN() GPIO_InitTypeDef GPIO_InitStructure; \
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7; \
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; \
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; \
GPIO_Init(GPIOB, &GPIO_InitStructure)
#define SDA_H() GPIO_SetBits(GPIOB, GPIO_Pin_7)
#define SDA_L() GPIO_ResetBits(GPIOB, GPIO_Pin_7)
#define SDA_READ() GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_7)
#define SCL_H() GPIO_SetBits(GPIOB, GPIO_Pin_6)
#define SCL_L() GPIO_ResetBits(GPIOB, GPIO_Pin_6)
void IIC_delay(uint16_t cnt)
{
uint16_t i;
while(cnt--)
{
i = 10;
while(i--);
}
}
void IIC_init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
SDA_H();
SCL_H();
}
void IIC_start(void)
{
SDA_OUT();
SDA_H();
SCL_H();
IIC_delay(5);
SDA_L();
IIC_delay(5);
SCL_L();
}
void IIC_stop(void)
{
SDA_OUT();
SCL_L();
SDA_L();
IIC_delay(5);
SCL_H();
SDA_H();
IIC_delay(5);
}
uint8_t IIC_wait_ack(void)
{
uint8_t i;
SDA_IN();
SDA_H();
IIC_delay(5);
SCL_H();
IIC_delay(5);
i = SDA_READ();
SCL_L();
return i;
}
void IIC_ack(void)
{
SDA_OUT();
SDA_L();
IIC_delay(5);
SCL_H();
IIC_delay(5);
SCL_L();
}
void IIC_nack(void)
{
SDA_OUT();
SDA_H();
IIC_delay(5);
SCL_H();
IIC_delay(5);
SCL_L();
}
void IIC_write_byte(uint8_t data)
{
uint8_t i;
SDA_OUT();
SCL_L();
for(i = 0; i < 8; i++)
{
if((data & 0x80) == 0x80)
SDA_H();
else
SDA_L();
data <<= 1;
IIC_delay(5);
SCL_H();
IIC_delay(5);
SCL_L();
}
}
uint8_t IIC_read_byte(uint8_t ack)
{
uint8_t i, data = 0;
SDA_IN();
for(i = 0; i < 8; i++)
{
data <<= 1;
SCL_L();
IIC_delay(5);
SCL_H();
IIC_delay(5);
if(SDA_READ())
data |= 0x01;
}
if(ack)
IIC_ack();
else
IIC_nack();
return data;
}
void TMP275AIDR_read_temp(float *temp)
{
uint8_t temp_data[2] = {0};
float t;
IIC_start();
IIC_write_byte(0x90); // 发送器件地址,写模式
IIC_wait_ack();
IIC_write_byte(0x00); // 发送子地址,温度数据寄存器
IIC_wait_ack();
IIC_start();
IIC_write_byte(0x91); // 发送器件地址,读模式
IIC_wait_ack();
temp_data[0] = IIC_read_byte(1);
temp_data[1] = IIC_read_byte(0);
IIC_stop();
t = (temp_data[0] << 4) | (temp_data[1] >> 4);
if(t & 0x800)
t = (0xFFFFF000 | t) / 16.0;
else
t /= 16.0;
*temp = t;
}
```
需要注意的是,以上代码是针对基于 STM32F10x 的开发板编写的,如果你的开发板不是 STM32F10x,可能需要修改相关的 GPIO 初始化和操作函数。另外,TMP275AIDR 的 I2C 地址是 0x48,因此在发送器件地址时需要将其左移一位,即发送 0x90(写模式)或 0x91(读模式)。
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)