用arduino ide写一段esp32 电位器控制电机转速代码
时间: 2023-09-26 20:11:31 浏览: 76
以下是一个基本的ESP32电位器控制电机转速的代码示例,你可以参考:
```
const int motorPin = 5; // 电机驱动引脚
const int potentiometerPin = 34; // 电位器引脚
void setup() {
pinMode(motorPin, OUTPUT);
pinMode(potentiometerPin, INPUT);
}
void loop() {
int potValue = analogRead(potentiometerPin); // 读取电位器数值
int motorSpeed = map(potValue, 0, 4095, 0, 255); // 将电位器数值映射到0-255之间的电机速度
analogWrite(motorPin, motorSpeed); // 输出电机速度
delay(10); // 稍作延时
}
```
在这个示例中,我们使用了ESP32的analogRead函数来读取电位器的数值,并使用map函数将数值映射到0-255之间的电机速度。然后使用analogWrite函数将电机速度输出到电机驱动引脚上,从而控制电机的转速。 注意:要确保电位器和电机都连接到正确的引脚上。
相关问题
用arduino ide 写一段esp 32 的esp now 发送示例
以下是一个基本的ESP32 ESP-NOW发送示例代码,使用Arduino IDE编写:
```C++
#include <esp_now.h>
#include <WiFi.h>
// Replace with your ESP32 board's MAC address
uint8_t broadcastAddress[] = {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF};
// Declare a struct to hold the data to be sent
struct Data {
int value1;
int value2;
int value3;
};
// Create a variable to hold the data
Data data;
void setup() {
// Start Serial communication
Serial.begin(115200);
// Initialize WiFi
WiFi.mode(WIFI_STA);
WiFi.disconnect();
// Initialize ESP-NOW
if (esp_now_init() != ESP_OK) {
Serial.println("Error initializing ESP-NOW");
return;
}
// Register broadcast address
esp_now_peer_info_t peerInfo;
peerInfo.channel = 0;
peerInfo.encrypt = false;
memcpy(peerInfo.peer_addr, broadcastAddress, 6);
if (esp_now_add_peer(&peerInfo) != ESP_OK) {
Serial.println("Failed to add broadcast peer");
return;
}
// Set the data values
data.value1 = 123;
data.value2 = 456;
data.value3 = 789;
}
void loop() {
// Send the data
esp_err_t result = esp_now_send(broadcastAddress, (uint8_t *) &data, sizeof(data));
// Check if data was sent successfully
if (result == ESP_OK) {
Serial.println("Data sent successfully");
} else {
Serial.println("Error sending data");
}
// Wait for 1 second before sending again
delay(1000);
}
```
此代码将初始化ESP-NOW,并设置广播地址。它还声明一个名为Data的结构来存储要发送的数据,并在setup()函数中设置数据值。在loop()函数中,代码将发送数据,并检查发送是否成功。最后,它将等待1秒钟,然后重新发送数据。
用arduino ide写一个ESP8266控制有源蜂鸣器的代码
好的,以下是ESP8266控制有源蜂鸣器的代码:
```
int buzzerPin = D1; //定义有源蜂鸣器的引脚
void setup() {
pinMode(buzzerPin, OUTPUT); //将有源蜂鸣器引脚设为输出模式
}
void loop() {
digitalWrite(buzzerPin, HIGH); //使蜂鸣器工作
delay(1000); //持续1秒
digitalWrite(buzzerPin, LOW); //关闭蜂鸣器
delay(1000); //持续1秒
}
```
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![-](https://csdnimg.cn/download_wenku/file_type_column_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)