stm32f103c8t6如何通过灯闪烁运行程序
时间: 2023-07-31 17:14:05 浏览: 79
首先,需要连接一个 LED 灯到 STM32F103C8T6 开发板的 GPIO 引脚上。然后,可以使用STM32的库函数来控制 GPIO 引脚的高低电平,从而实现灯的闪烁。
以下是一个简单的示例程序,可以让 LED 灯每隔一段时间闪烁:
```c
#include "stm32f10x.h"
int main(void)
{
// 初始化 LED 引脚
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// 循环闪烁 LED 灯
while (1)
{
GPIO_SetBits(GPIOC, GPIO_Pin_13);
Delay(1000000);
GPIO_ResetBits(GPIOC, GPIO_Pin_13);
Delay(1000000);
}
}
void Delay(__IO uint32_t nCount)
{
while(nCount--)
{
}
}
```
在这个示例程序中,首先使用 `RCC_APB2PeriphClockCmd()` 函数初始化了 PC13 引脚,然后使用 `GPIO_Init()` 函数配置了引脚的模式为输出模式。接着,在一个无限循环中,通过 `GPIO_SetBits()` 和 `GPIO_ResetBits()` 函数分别将引脚置为高电平和低电平,从而实现 LED 灯的闪烁。最后,使用 `Delay()` 函数实现了一个简单的延时函数,以控制 LED 灯的闪烁频率。
注意,这只是一个简单的示例程序,实际的应用程序可能需要更加复杂的控制逻辑和算法。
相关推荐
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)