在vivado中用FIFO储存器达到一个同步的效果,每20s更新一次,用VHDL怎么写
时间: 2024-03-06 12:50:38 浏览: 24
在VHDL中,可以使用FIFO(First-In-First-Out)储存器实现同步效果。下面是一个使用FIFO储存器实现每20秒更新一次的示例代码:
```vhdl
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;
entity fifo_sync is
port (
clk : in std_logic;
rst : in std_logic;
input : in std_logic;
output : out std_logic
);
end entity fifo_sync;
architecture behavioral of fifo_sync is
-- 设置FIFO的深度
constant FIFO_DEPTH : integer := 20;
-- 定义FIFO储存器的信号
signal fifo_full : std_logic;
signal fifo_empty : std_logic;
signal fifo_data : std_logic_vector(7 downto 0);
signal fifo_wren : std_logic;
signal fifo_rdren : std_logic;
signal fifo_clk : std_logic;
signal fifo_rst : std_logic;
signal fifo_dout : std_logic_vector(7 downto 0);
-- 定义计数器的信号
signal count : integer range 0 to 200000000;
signal tick : std_logic;
begin
-- 实例化FIFO储存器
fifo_inst : entity work.fifo_generator
generic map (
DATA_WIDTH => 8,
ADDR_WIDTH => ceil(log2(FIFO_DEPTH)),
INIT_SV => x"00"
)
port map (
clk => fifo_clk,
rst => fifo_rst,
we => fifo_wren,
re => fifo_rdren,
din => input,
dout => fifo_dout,
full => fifo_full,
empty => fifo_empty,
wr_ptr => open,
rd_ptr => open
);
-- 将FIFO的读写使能信号与时钟同步
fifo_clk <= clk;
fifo_rst <= rst;
-- 初始化FIFO的写使能信号为高电平
fifo_wren <= '1';
-- 根据FIFO的状态来更新输出信号
process (fifo_empty, fifo_dout)
begin
if fifo_empty = '0' then
output <= fifo_dout(0);
end if;
end process;
-- 每秒钟产生一个时钟信号
process (clk)
begin
if rising_edge(clk) then
-- 将计数器加1
if count = 200000000 then
count <= 0;
tick <= '1';
else
count <= count + 1;
tick <= '0';
end if;
end if;
end process;
-- 当计数器累计到20秒时,将写使能信号置为低电平,停止写入新数据
process (tick)
begin
if tick = '1' then
if rst = '1' then
fifo_wren <= '1';
else
if fifo_full = '1' then
fifo_wren <= '0';
else
fifo_wren <= '1';
end if;
end if;
end if;
end process;
-- 当FIFO中的数据达到一定数量时,将读使能信号置为高电平,开始读出数据
process (clk)
begin
if rising_edge(clk) then
if rst = '1' then
fifo_rdren <= '0';
else
if fifo_empty = '0' and fifo_full = '0' and
std_logic_vector(unsigned(fifo_dout) + 1) = to_unsigned(FIFO_DEPTH-1, fifo_dout'length) then
fifo_rdren <= '1';
else
fifo_rdren <= '0';
end if;
end if;
end if;
end process;
end architecture behavioral;
```
这是一个简单的同步电路,使用了一个FIFO储存器来存储输入信号。当计数器累计到20秒时,将写使能信号置为低电平,停止写入新数据。输出信号将会被更新。需要注意的是,这里使用了一个名为`fifo_generator`的FIFO生成器,需要在代码中进行实例化,并将其与FIFO的读写使能信号连接在一起。