stm32f103c8t6点亮led
时间: 2023-08-25 22:07:48 浏览: 82
以下是使用STM32F103C8T6点亮LED的示例代码:
```c
#include "stm32f10x.h"
#include "stm32f10x_gpio.h"
#include "stm32f10x_rcc.h"
int main(void)
{
// 使能GPIOC外设时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
// 初始化GPIOC为推挽输出模式
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// 点亮LED
GPIO_ResetBits(GPIOC, GPIO_Pin_13);
while(1)
{
// 循环等待
}
}
```
该代码将PC13引脚配置为推挽输出模式,并在该引脚上输出低电平,从而点亮连接到该引脚上的LED。如果需要控制LED的亮灭,可以通过改变引脚输出电平的方式实现。
相关问题
stm32f103c8t6点亮LED
要点亮STM32F103C8T6上的LED,你需要按照以下步骤进行:
1. 首先,将需要使用的GPIO口配置为输出模式,并将相应的引脚设置为高电平。例如,如果你想要点亮PA1口上的LED,那么你需要进行如下配置:
```
//开启GPIOA时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
//将PA1口配置为输出模式
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//将PA1口置高电平,点亮LED
GPIO_SetBits(GPIOA, GPIO_Pin_1);
```
2. 程序运行后,LED即可点亮。
STM32F103C8T6点亮LED
Sure, to light up an LED using STM32F103C8T6, you need to connect the LED to a GPIO pin of the microcontroller and set the pin to output mode. Then, you can simply toggle the pin high and low to turn the LED on and off. Here's a sample code to do that:
```
#include "stm32f10x.h"
int main(void)
{
// Enable GPIOC peripheral clock
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE);
// Configure GPIOC Pin 13 as output push-pull
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOC, &GPIO_InitStructure);
// Toggle LED on and off
while(1)
{
GPIO_WriteBit(GPIOC, GPIO_Pin_13, Bit_SET);
Delay(1000);
GPIO_WriteBit(GPIOC, GPIO_Pin_13, Bit_RESET);
Delay(1000);
}
}
```
Note: This is just a sample code and you may need to modify it according to your specific requirements.
阅读全文