使用STM32CubeIDE编写基于stm32单片机的DTH11温湿度传感器和ESP-01S模块的代码

好的，以下是基于STM32CubeIDE编写DTH11温湿度传感器和ESP-01S模块的代码：

#include "main.h"
#include "dht11.h"
#include "esp8266.h"

UART_HandleTypeDef huart1;

void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);

int main(void)
{
  HAL_Init();
  SystemClock_Config();
  MX_GPIO_Init();
  MX_USART1_UART_Init();

  while (1)
  {
     uint8_t dht11_data[5];
     if(DHT11_Read_Data(dht11_data) == DHT11_OK)
     {
         char buffer[100];
         sprintf(buffer,"Temperature: %d.%d Humidity: %d.%d\r\n",dht11_data[2],dht11_data[3],dht11_data[0],dht11_data[1]);
         HAL_UART_Transmit(&huart1,(uint8_t*)buffer,strlen(buffer),100);
         ESP8266_Send_AT_Command("AT+CIPSTART=\"TCP\",\"192.168.1.2\",80");
         ESP8266_Send_AT_Command("AT+CIPSEND=50");
         sprintf(buffer,"GET /esp8266.php?temperature=%d.%d&humidity=%d.%d\r\n",dht11_data[2],dht11_data[3],dht11_data[0],dht11_data[1]);
         HAL_UART_Transmit(&huart1,(uint8_t*)buffer,strlen(buffer),100);
         HAL_Delay(1000);
     }
     else
     {
         HAL_UART_Transmit(&huart1,(uint8_t*)"DHT11 Read Error\r\n",strlen("DHT11 Read Error\r\n"),100);
     }
  }
}

void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
  {
    Error_Handler();
  }
}

static void MX_USART1_UART_Init(void)
{
  huart1.Instance = USART1;
  huart1.Init.BaudRate = 115200;
  huart1.Init.WordLength = UART_WORDLENGTH_8B;
  huart1.Init.StopBits = UART_STOPBITS_1;
  huart1.Init.Parity = UART_PARITY_NONE;
  huart1.Init.Mode = UART_MODE_TX_RX;
  huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  huart1.Init.OverSampling = UART_OVERSAMPLING_16;
  if (HAL_UART_Init(&huart1) != HAL_OK)
  {
    Error_Handler();
  }
}

static void MX_GPIO_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOA_CLK_ENABLE();

  /*Configure GPIO pin : PA0 */
  GPIO_InitStruct.Pin = GPIO_PIN_0;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}

void Error_Handler(void)
{
  __disable_irq();
  while (1)
  {
  }
}

#ifdef USE_FULL_ASSERT
void assert_failed(uint8_t *file, uint32_t line)
{
}
#endif

在以上代码中，我们首先进行了一些头文件和宏定义的引用和声明，然后在main函数中，我们首先进行了DHT11传感器数据的读取。如果读取成功，则会通过串口发送传感器的温度和湿度数据，并且通过ESP-01S模块发送这些数据到服务器。最后，我们在while循环中添加了一个延时函数，以便等待下一次的读取。

需要注意的是，为了使DHT11传感器和ESP-01S模块能够正常工作，我们需要引用dht11.h和esp8266.h这两个头文件，同时也需要提前进行相应的初始化操作。