nb-iot串口通信stm32
时间: 2023-06-06 20:02:51 浏览: 147
NB-IoT串口通信是一种基于物联网技术的远程通信方式,它可以实现设备之间的数据传输和远程控制。STM32是一种嵌入式芯片,具有高性能、低功耗等特点,非常适合作为NB-IoT串口通信的控制器。
使用STM32进行NB-IoT串口通信,需要使用NB-IoT模块和串口通信模块。首先,需要将NB-IoT模块与STM32进行连接,并使用AT指令进行配置和设置。然后,将NB-IoT模块和串口通信模块进行连接,使用STM32的串口接口进行数据传输和接收。
在NB-IoT串口通信中,可以通过数据包进行通信,将不同设备之间的数据进行交换和传输。同时,可以对设备进行远程控制,实现远程操作和管理。同时,在NB-IoT通信中,需要注意安全性问题,加密通信和数据隐私保护是非常重要的。
总的来说,NB-IoT串口通信是一种非常实用的物联网通信方式,可以实现多种设备之间的数据传输和控制。使用STM32进行NB-IoT串口通信,可以充分发挥其高性能和低功耗等优点,为物联网应用带来便利。
相关问题
NB-IOT硬件驱动开发代码
NB-IoT硬件驱动开发代码的实现过程与具体的硬件平台和NB-IoT模组有关,下面是一份基于 STM32 平台和SIMCom SIM7020E模组的NB-IoT硬件驱动开发代码,供参考:
1. 硬件接口定义:
```c
/* 串口接口定义 */
#define NB_UART USART1
#define NB_UART_CLK RCC_APB2Periph_USART1
#define NB_UART_CLK_CMD RCC_APB2PeriphClockCmd
#define NB_UART_IRQn USART1_IRQn
#define NB_UART_IRQHandler USART1_IRQHandler
#define NB_UART_TX_PIN GPIO_Pin_9
#define NB_UART_RX_PIN GPIO_Pin_10
#define NB_UART_GPIO GPIOA
#define NB_UART_GPIO_CLK RCC_APB2Periph_GPIOA
/* GPIO接口定义 */
#define NB_PWRKEY_PIN GPIO_Pin_1
#define NB_PWRKEY_GPIO GPIOB
#define NB_PWRKEY_GPIO_CLK RCC_APB2Periph_GPIOB
#define NB_PWRKEY_HIGH() GPIO_SetBits(NB_PWRKEY_GPIO, NB_PWRKEY_PIN)
#define NB_PWRKEY_LOW() GPIO_ResetBits(NB_PWRKEY_GPIO, NB_PWRKEY_PIN)
#define NB_STATUS_PIN GPIO_Pin_0
#define NB_STATUS_GPIO GPIOB
#define NB_STATUS_GPIO_CLK RCC_APB2Periph_GPIOB
#define NB_STATUS_READ() GPIO_ReadInputDataBit(NB_STATUS_GPIO, NB_STATUS_PIN)
```
2. 驱动程序编写:
(1)初始化NB-IOT模组
```c
void nb_init(void)
{
/* 使能UART和GPIO时钟 */
RCC_APB2PeriphClockCmd(NB_UART_CLK | NB_UART_GPIO_CLK | NB_PWRKEY_GPIO_CLK | NB_STATUS_GPIO_CLK, ENABLE);
/* 配置UART引脚 */
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = NB_UART_TX_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(NB_UART_GPIO, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = NB_UART_RX_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_Init(NB_UART_GPIO, &GPIO_InitStructure);
/* 配置GPIO引脚 */
GPIO_InitStructure.GPIO_Pin = NB_PWRKEY_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(NB_PWRKEY_GPIO, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = NB_STATUS_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(NB_STATUS_GPIO, &GPIO_InitStructure);
/* 复位NB-IOT模组 */
NB_PWRKEY_LOW();
delay_ms(100);
NB_PWRKEY_HIGH();
delay_ms(5000);
}
```
(2)发送AT指令
```c
uint8_t nb_send_at_cmd(char *cmd, char *resp, uint16_t timeout)
{
uint8_t i = 0, j = 0;
uint8_t ret = 0;
char rx_buf[256] = {0};
uint32_t t1 = 0, t2 = 0;
/* 发送AT指令 */
USART_ITConfig(NB_UART, USART_IT_RXNE, DISABLE);
USART_ITConfig(NB_UART, USART_IT_TC, ENABLE);
while (cmd[i] != '\0')
{
USART_SendData(NB_UART, (uint16_t)cmd[i++]);
while (USART_GetFlagStatus(NB_UART, USART_FLAG_TC) == RESET);
}
/* 等待模组应答 */
USART_ITConfig(NB_UART, USART_IT_TC, DISABLE);
USART_ITConfig(NB_UART, USART_IT_RXNE, ENABLE);
t1 = millis();
while ((millis() - t1) < timeout)
{
if (USART_GetFlagStatus(NB_UART, USART_FLAG_RXNE) == SET)
{
rx_buf[j++] = (char)USART_ReceiveData(NB_UART);
}
if (strstr(rx_buf, resp) != NULL)
{
ret = 1;
break;
}
}
return ret;
}
```
(3)数据收发
```c
void nb_send_data(uint8_t *data, uint16_t len)
{
/* 发送数据 */
char cmd[64] = {0};
sprintf(cmd, "AT+NMGS=%d,%02X", len, data[0]);
nb_send_at_cmd(cmd, "OK", 2000);
memset(cmd, 0, sizeof(cmd));
for (uint16_t i = 0; i < len; i++)
{
sprintf(cmd + strlen(cmd), "%02X", data[i]);
}
nb_send_at_cmd(cmd, "OK", 2000);
}
uint16_t nb_recv_data(uint8_t *data)
{
/* 接收数据 */
char cmd[64] = {0};
nb_send_at_cmd("AT+NMGR=1", "+NMGR:", 2000);
char *ptr = strstr((char *)nb_rx_buf, ",");
ptr++;
uint16_t len = 0;
sscanf(ptr, "%02X", &len);
ptr += 2;
for (uint16_t i = 0; i < len; i++)
{
sscanf(ptr + i * 2, "%02X", (unsigned int *)(data + i));
}
return len;
}
```
3. 应用程序开发
(1)连接网络
```c
uint8_t nb_connect_network(void)
{
nb_send_at_cmd("AT+CFUN=0", "OK", 2000);
nb_send_at_cmd("AT+CFUN=1", "OK", 2000);
nb_send_at_cmd("AT+COPS=1,2,\"46001\"", "OK", 2000);
nb_send_at_cmd("AT+CGDCONT=1,\"IP\",\"ctnet\"", "OK", 2000);
nb_send_at_cmd("AT+CFUN=0", "OK", 2000);
nb_send_at_cmd("AT+CFUN=1", "OK", 2000);
nb_send_at_cmd("AT+CSQ", "OK", 2000);
uint8_t i = 0;
while (i < 10)
{
if (NB_STATUS_READ() == 0)
{
return 1;
}
delay_ms(1000);
i++;
}
return 0;
}
```
(2)发送数据
```c
uint8_t nb_send(uint8_t *data, uint16_t len)
{
uint8_t retry = 3;
while (retry > 0)
{
nb_send_data(data, len);
if (nb_send_at_cmd("AT+NMGS?", "+NMGS:", 2000) == 1)
{
return 1;
}
retry--;
}
return 0;
}
```
(3)接收数据
```c
uint16_t nb_recv(uint8_t *data)
{
uint16_t len = 0;
if (nb_send_at_cmd("AT+NMGR?", "+NMGR:", 2000) == 1)
{
len = nb_recv_data(data);
}
return len;
}
```
以上代码仅供参考,实际使用时需要根据具体的硬件平台和NB-IoT模组进行相应的修改和调试。
stm32与nb-lot海水养殖监控系统程序
STM32与NB-IoT海水养殖监控系统程序的主要目的是通过STM32微控制器和NB-IoT网络实现对海水养殖过程的实时监控和远程管理。该系统能够提供养殖池水质、温度、溶氧量等关键参数的监测,并且可以通过移动端或云平台对养殖环境进行远程控制。
在程序开发方面,首先需要使用STM32开发工具(如Keil等)进行编程。通过编程,我们可以设置STM32与各种传感器(如温度传感器、PH传感器、溶氧传感器等)之间的接口,以实现对养殖池环境参数的数据采集。
其次,我们需要使用NB-IoT模块与NB-IoT网络进行通信。通过NB-IoT模块,我们可以将采集到的数据传输到远程服务器或云平台,并实现与移动端的连接。在程序中,需要编写与NB-IoT模块通信的相关代码,以确保数据的可靠传输。
同时,还需要编写与移动端或云平台通信的代码,以便用户可以通过移动应用程序或网页对养殖环境进行实时监控和远程控制。这涉及到建立和维护与移动端或云平台的通信连接,以及实现数据的上传和命令的下发。
最后,需要将所有的功能代码进行整合和调试,确保程序的稳定性和可靠性。在调试过程中,可以通过串口打印、调试工具等方式对程序进行调试,以确保各个模块的正常运行和数据的准确性。
总之,STM32与NB-IoT海水养殖监控系统程序的开发需要进行传感器接口的编程、与NB-IoT模块的通信编程以及与移动端或云平台的通信编程。通过这些工作,可以实现对海水养殖环境的实时监控和远程管理。