stm32sf103连接nodemcu
时间: 2023-11-03 10:06:15 浏览: 46
要连接STM32F103与NodeMCU,你需要将它们之间的串口连接起来。首先,将STM32F103的TX引脚连接到NodeMCU的RX引脚,将STM32F103的RX引脚连接到NodeMCU的TX引脚。然后,确保两个设备使用相同的电源和共同的地线。最后,你需要编写代码,使STM32F103发送数据到NodeMCU,或者从NodeMCU接收数据到STM32F103。在代码中,你需要设置串口的波特率、数据位、校验位和停止位等参数,以确保两个设备之间的通信正确无误。
相关问题
stm32sf103连接nodemcu代码
要将STM32F103与NodeMCU连接,您可以使用串行通信协议,例如UART或SPI。以下是一个可能的示例代码:
对于STM32F103,您可以使用内置的USART模块来设置串行通信。以下是示例代码:
```
#include "stm32f10x.h"
void USART1_Init(void)
{
// Enable USART1 clock
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
// Configure USART1 pins
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Configure USART1
USART_InitTypeDef USART_InitStructure;
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Tx | USART_Mode_Rx;
USART_Init(USART1, &USART_InitStructure);
// Enable USART1
USART_Cmd(USART1, ENABLE);
}
void USART1_SendByte(uint8_t byte)
{
while (USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
USART_SendData(USART1, byte);
}
uint8_t USART1_ReceiveByte(void)
{
while (USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == RESET);
return USART_ReceiveData(USART1);
}
```
对于NodeMCU,您可以使用内置的UART或SPI模块来设置串行通信。以下是示例代码:
使用UART:
```
#include <SoftwareSerial.h>
SoftwareSerial mySerial(D2, D1); // RX, TX
void setup() {
mySerial.begin(9600);
}
void loop() {
if (mySerial.available()) {
uint8_t byte = mySerial.read();
// Do something with the received byte
}
}
```
使用SPI:
```
#include <SPI.h>
void setup() {
SPI.begin();
pinMode(D8, OUTPUT); // CS pin
}
void loop() {
digitalWrite(D8, LOW); // Select NodeMCU
SPI.transfer(0x01); // Send data
digitalWrite(D8, HIGH); // Deselect NodeMCU
}
```
请注意,这只是示例代码,您需要根据您的具体硬件和通信协议进行修改。
nodemcu波特率9600与stm32f103波特率115200怎么连接
如果你想通过串口连接nodemcu和stm32f103,你需要确保它们的波特率一致。在这种情况下,你需要将nodemcu的波特率设置为115200,这样它才能与stm32f103通信。
以下是连接步骤:
1.连接nodemcu的TX引脚到stm32f103的RX引脚,以及nodemcu的RX引脚到stm32f103的TX引脚。
2.将nodemcu的波特率设置为115200。你可以通过Arduino IDE或其他串口工具进行设置。
3.在stm32f103中,你需要使用相应的串口库,例如STM32CubeMX或STMCubeIDE,以确保你的代码正确地配置了串口设置。
4.在stm32f103中,你需要设置正确的波特率,比如115200。
这样,你就能够通过串口连接nodemcu和stm32f103,并且它们能够正常地进行通信。