没有合适的资源？快使用搜索试试~ 我知道了~

Veritas NetBackup™ 5340 Appliance Hardware Installation Guide - ...

需积分: 5 0 下载量 11 浏览量更新于2023-11-23 收藏 15.84MB PDF 举报

《NetBackup 5340 Appliance Hardware Installation Guide》是由Veritas Technologies LLC发布的一份安装指南。该安装指南最新更新日期为2017年11月6日，适用于NetBackup 5340 Appliance硬件安装。本指南版权归Veritas Technologies LLC所有，未经授权禁止复制或传播。Veritas和Veritas Logo为Veritas Technologies LLC或其附属公司在美国和其他国家的商标或注册商标。本产品可能包含第三方软件，Veritas需要对第三方软件进行归属性述。其中一些第三方软件基于开放源代码或自由软件许可证。此外，软件附带的许可协议并不改变您在这些开放源代码或自由软件许可证下可能拥有的权利或义务。

Each cooling module contains two fans. Cooling modules can be individually

replaced but cannot be taken apart to replace only one fan.

Refer to the following sections for information about the I/O modules.

See “5U84 storage shelf RAID controller” on page 14.

See “5U84 storage shelf Expansion module” on page 15.

5U84 storage shelf RAID controller

The Primary Storage Shelf contains two RAID controllers in I/O modules. The

controllers are labeled A and B, from left to right as you look at the rear panel of a

shelf. Each controller has two sets of Fibre Channel (FC) ports. From left to right

the set of two FC ports for each controller are labeled 1 and 0. The SAS3 port on

the left side of each RAID controller connects to a SAS3 port on the Expansion I/O

module.

SAS3 port

FC ports

1 and 0

FC ports

1 and 0

14Hardware overview

5U84 storage shelf RAID controller

5U84 storage shelf Expansion module

Each Expansion Storage Shelf contains two I/O modules. The modules are labeled

A and B, from left to right as you look at the rear panel of a shelf. Each module has

three SAS3 ports that are labeled A, B, and C from left to right. A yellow label states

that port B is for attachment to a server only. The SAS3 ports connect to the SAS

port on each RAID controller on the Primary Shelf and to other Expansion Shelves.

SAS3 ports

Ethernet

port

B C

NetBackup 5340 cables and connectors

The compute node connects to the storage shelf RAID controller with FC cables.

The compute node supports an optional SAS3 adapter port to enable the connection

of a SAS2 or SAS3 tape drive. You can use a SAS3 cable or a SAS2-SAS3 cable

depending on your tape device.

Storage shelf RAID controllers connect to storage shelf Expansion I/O modules

with SAS3 cables.

The power connector that attaches to a storage shelf has a right-angled form factor.

A security tie assures continued connection between the power cable and the

storage shelf.

15Hardware overview

5U84 storage shelf Expansion module

Preinstallation

requirements

This chapter includes the following topics:

■ Customer-provided environment and supplies

■ Storage shelf shipping container contents

■ Compute node shipping container contents

■ Determining rack locations

■ Heat dissipation guidelines

■ Cable length verification

■ Prerequisites for IPMI configuration

Customer-provided environment and supplies

For best ventilation, the rack cabinet:

■ Should be at least 100 cm (4 feet) from walls

■ Should have at least 100 cm (4 feet) from other cabinets on the front and back

of the compute node and the storage shelves

■ Refer to the following section for more details.

See “Heat dissipation guidelines” on page 21.

The following list describes the necessary personnel and equipment that are needed

at the installation site:

■ The storage shelf rails can extend from 713mm (28.07in) to 884mm (33.23in)

in length. Be sure that your racks accommodate these rails.

Chapter

■ At least one person or a mechanical lift to move the compute node.

■ Three people or a mechanical lift to move each storage shelf.

■ A magnetic Philips-head screw driver to install the storage shelf rails into the

rack.

■ A Torx T20 screwdriver to lock each of the two drawers in a storage shelf.

■ Ethernet and Fibre Channel (FC) cables to connect the compute node to your

corporate network.

■ A USB-keyboard and a monitor to connect to the compute node.

■ A 19-inch rack with dual Power Distribution Units (PDUs) with 120VAC or

220VAC power input for the compute node.

■ A 19-inch rack with dual Power Distribution Units (PDUs) with 220VAC power

input for the storage shelves.

Storage shelf shipping container contents

Each storage shelf container includes other boxes and contents as follows.

■ Open Me First envelope, containing:

■ Deployment plan that provides basic information and links to detailed

information

■ Cable straps

■ Envelope, containing;

■ Warranty agreement

■ Environmental compliance statement

■ Hardware cable connections poster

■ Rack template

■ Rack rails and mounting hardware

■ Two SAS-3 cables

■ Two power cords

The disk drives ship separately from the storage shelves. Each disk drive shipping

container contains 42 disk drives in carriers.

When the storage shelves have been installed into a rack you install the disk drives

into the drawers.

17Preinstallation requirements

Storage shelf shipping container contents

剩余82页未读，继续阅读

weixin_40191861_zj

粉丝: 87
资源: 1万+

上传资源快速赚钱

我的内容管理展开

我的资源快来上传第一个资源

我的收益

登录查看自己的收益

我的积分登录查看自己的积分

我的C币登录后查看C币余额

我的收藏

我的下载

下载帮助

Veritas NetBackup™ 5340 Appliance Hardware Installation Guide - ...

NetBackup 5240 Appliance Hardware Installation Guide.pdf

NetBackup 5330 Appliance Hardware Installation Guide.pdf

NetBackup 5230 Appliance Hardware Installation Guide.pdf

Veritas 5340 Appliance Hardware Installation Guide.pdf

Veritas 5150 Appliance Hardware Installation Guide.pdf

Veritas 5350 Appliance Hardware Installation Guide.pdf

Veritas 5250 Appliance Hardware Installation Guide.pdf

Veritas Access 3340 Appliance Hardware Installation Guide.pdf

NetBackup 5330 Appliance Hardware Installation Guide - 3.pdf

NetBackup 5330 Appliance Hardware Installation Guide - 272.pdf

最新资源