移动网络与宽带入门：从GSM到LTE-Advanced Pro和5G

LTE

需积分: 10 49 浏览量更新于2024-07-17 1 收藏 6.97MB PDF 举报

身份认证购VIP最低享 7 折!

领优惠券(最高得80元）

"《From GSM to LTE-Advanced Pro and 5G: An Introduction to Mobile Networks and Mobile Broadband》是无线通信领域的一本专业书籍，由Martin Sauter撰写，第三版于2017年发布。该书涵盖了从最初的GSM（全球系统 for 移动通信）技术到最新的LTE-Advanced Pro和5G（第五代移动通信）的演进历程，全面介绍移动网络和移动宽带的基本概念和技术细节。" 本文将深入探讨移动通信技术的发展历程，从GSM开始，这是一种2G（第二代）通信标准，主要实现了语音通信和低速数据传输。GSM的出现标志着数字移动通信时代的开端，它引入了SIM卡、漫游和加密通信等特性，极大提升了通信质量和安全性。随后，我们进入3G（第三代）时代，如UMTS（通用移动通信系统）和HSPA（高速分组接入），这些技术显著提高了数据传输速率，支持了多媒体服务和移动互联网的初步发展。接着，LTE（长期演进）作为4G（第四代）的先驱，显著提升了数据速度和网络效率，为高清视频流、在线游戏和云计算等应用提供了基础。在LTE的基础上，LTE-Advanced进一步增强了网络性能，通过载波聚合、MIMO（多输入多输出）和其他先进技术，实现了接近千兆比特每秒的峰值速度。然后，书中的重点是5G，这是当前最前沿的移动通信标准，旨在提供超高速率、极低延迟和大规模连接能力。5G的关键技术包括毫米波、网络切片、边缘计算和物联网（IoT）集成。这些技术的引入不仅改变了个人通信体验，还对自动驾驶、远程医疗、智慧城市等领域产生了深远影响。此外，书中还会详细讨论移动网络的架构，包括核心网、接入网和频谱管理，以及与移动宽带相关的无线传播、信号处理和网络优化技术。同时，作者还会介绍相关的法规和标准，以及如何在实际中实施和维护这些先进的通信系统。《From GSM to LTE-Advanced Pro and 5G》是一本适合电信行业专业人士、研究人员和学生阅读的权威教材，通过本书，读者可以全面了解移动通信技术的过去、现在和未来。

资源详情

资源推荐

From GSM to LTE-Advanced Pro and 5G

1.1.1 Classic Circuit Switching

The GSM mobile telecommunication network has been designed as a circuit‐switched

network in a similar way to fixed‐line phone networks. At the beginning of a call, the net-

work establishes a direct connection between two parties, which is then used exclusively for this

conversation. As shown in Figure1.1, the switching center uses a switching matrix to con-

nect any originating party to any destination party. Once the connection has been estab-

lished, the conversation is then transparently transmitted via the switching matrix between

the two parties. The switching center only becomes active again to clear the connection in

the switching matrix if one of the parties wants to end the call. This approach is identical in

both mobile and fixed‐line networks. Early fixed‐line telecommunication networks were

designed only for voice communication, for which an analog connection between the par-

ties was established. In the mid‐1980s, analog technology was superseded by digital tech-

nology in the switching center. This meant that calls were no longer sent over an analog

line from the originator to the terminator. Instead, the switching center digitized the analog

signal that it received from the subscribers, which were directly attached to it, and for-

warded the digitized signal to the terminating switching center. There, the digital signal

was again converted back to an analog signal, which was then sent over the copper cable to

the terminating party. In some countries, ISDN (Integrated Services Digital Network) lines

were quite popular. With this system, the transmission became fully digital and the conver-

sion back to an analog audio signal was done directly in the phone.

GSM reused much of the fixed‐line technology that was already available at the time the

standards were created. Thus, existing technologies such as switching centers and long‐

distance communication equipment were used. The main development for GSM, as

shown in Figure1.2, was the means to wirelessly connect the subscribers to the network.

In fixed‐line networks, subscriber connectivity is very simple as only two dedicated wires

are necessary per user. In a GSM network, however, the subscribers are mobile and can

change their location at any time. Thus, it is not possible to use the same input and output

in the switching matrix for a user for each call as is the case in fixed‐line networks.

As a mobile network consists of many switching centers, with each covering a certain

geographical area, it is not even possible to predict in advance which switching center a

Figure1.1 Switching matrix in a

switching center.

Global System for Mobile Communications (GSM)

call should be forwarded to for a certain subscriber. This means that the software for

subscriber management and routing of calls of fixed‐line networks cannot be used for

GSM. Instead of a static call‐routing mechanism, a flexible mobility management archi-

tecture in the core network became necessary, which needed to be aware of the current

location of the subscriber and thus able to route calls to them at any time.

It was also necessary to be able to flexibly change the routing of an ongoing call as a

subscriber can roam freely and thus might leave the coverage area of the radio transmit-

ter of the network over which the call was established. While there was a big difference

between the software of a fixed switching center and a Mobile Switching Center (MSC),

the hardware as well as the lower layers of the software which are responsible, for exam-

ple, for the handling of the switching matrix were mostly identical. Therefore, most

telecommunication equipment vendors like Ericsson, Nokia Solutions and Networks,

Huawei and Alcatel‐Lucent offered their switching center hardware both for fixed‐line

and mobile networks. Only the software in the switching center determined whether

the hardware was used in a fixed or mobile network (see Figure1.2).

1.1.2 Virtual Circuit Switching over IP

While in the 1990s voice calls were the dominating form of communication, this has

significantly changed today with the rise of the Internet. While voice calls remain

important, other forms of communication such as e‐mail, instant messaging (IM), social

networks (e.g. Facebook), blogs, wikis and many more play an even bigger role. All these

services share the Internet Protocol (IP) as a transport protocol and globally connect

people via the Internet.

While circuit switching establishes an exclusive channel between two parties, the

Internet is based on transferring individual data packets. A link with a high bandwidth

is used to transfer the packets of many users. By using the destination address contained

in each packet, each network node that the packet traverses decides over which outgo-

ing link to forward the packet. Further details can be found in Chapter2.

Owing to the rise of the Internet and IP‐based applications, network operators thus

had to maintain two separate networks: a circuit‐switched network for voice calls and a

packet‐switched network for Internet‐based services.

As the simultaneous operation of two different networks is very inefficient and costly,

most network operators have, in the meantime, replaced the switching matrix in the

Switching and signaling

software

Fixed line subscriber and

call control

Operating system of the

switching center

Mobile subscriber management

Mobility management

Call control

Switching and signaling

software

Operating system of the

switching center

Figure1.2 Necessary software changes to adapt a fixed‐line switching center for a wireless network.

From GSM to LTE-Advanced Pro and 5G

MSC with a device referred to as a media gateway. This allows them to virtualize circuit

switching and to transfer voice calls over IP packets. The physical presence of a circuit‐

switched infrastructure is thus no longer necessary and the network operator can

concentrate on maintaining and expanding a single IP‐based network. This approach

has been standardized under the name ‘Bearer‐Independent Core Network’ (BICN).

The basic operation of GSM is not changed by this virtualization. The main differences

can be found in the lower protocol levels for call signaling and voice call transmission.

This will be looked at in more detail in the remainder of this chapter.

The trend toward IP‐based communication can also be observed in the GSM radio

network especially when a radio base station site supports GSM, UMTS and LTE

simultaneously. Typically, connectivity is then established over a single IP‐based link.

The air interface between the mobile devices and the network is not affected by the

transition from circuit to packet switching. For mobile devices, whether the network

uses classic or virtual circuit switching is therefore completely transparent.

1.2 Standards

As many network infrastructure manufacturers compete globally for orders from

telecommunication network operators, standardization of interfaces and procedures is

necessary. Without standards, which are defined by the International Telecommunication

Union (ITU), it would not be possible to make phone calls internationally and network

operators would be bound to the supplier they initially select for the delivery of their

network components. One of the most important ITU standards, discussed in Section1.4,

is the Signaling System Number 7 (SS‐7), which is used for call routing. Many ITU stand-

ards, however, only represent the lowest common denominator as most countries have

specified their own national extensions. In practice, this incurs a high cost for software

development for each country as a different set of extensions needs to be implemented

in order for a vendor to be able to sell its equipment. Furthermore, the interconnection

of networks of different countries is complicated by this.

GSM, for the first time, set a common standard for Europe for wireless networks. Due

to its success it was later adopted around the globe. This is the main reason why sub-

scribers can roam in GSM networks across the world that have roaming agreements

with each other. The common standard also substantially reduces research and devel-

opment costs as hardware and software can now be sold worldwide with only minor

adaptations for the local market. The European Telecommunication Standards Institute

(ETSI), which is also responsible for a number of other standards, was the main body

responsible for the creation of the GSM standard. The ETSI GSM standards are com-

posed of a substantial number of standards documents, each of which is called a techni-

cal specification (TS) and describes a particular part of the system. In the following

chapters, many of these specifications are referenced and can thus be used for further

information about a specific topic. Due to the global success of GSM, the 3

Generation

Partnership Project (3GPP) was later founded as a global organization and ETSI became

one of the regional standardization bodies of the project. Today, 3GPP is responsible for

maintaining and further developing the GSM, UMTS, LTE and 5G standards. All docu-

ments are freely available on the Internet at http://www.etsi.org [1] or at http://

www.3gpp.org [2].

Global System for Mobile Communications (GSM)

1.3 Transmission Speeds

The smallest transmission speed unit in a classic circuit‐switched telecommunication

network is the digital signal level 0 (DS0) channel. It has a fixed transmission speed of

64 kbit/s. Such a channel can be used to transfer voice or data, and thus it is usually not

called a speech channel but simply referred to as a user data channel.

The reference unit of a telecommunication network is an E‐1 connection in Europe

and a T‐1 connection in the United States, which use either a twisted pair or coaxial

copper cable. The gross datarate is 2.048 Mbit/s for an E‐1 connection and 1.544 Mbit/s

for a T‐1. An E‐1 is divided into 32 timeslots of 64 kbit/s each, as shown in Figure1.3

while a T‐1 is divided into 24 timeslots of 64 kbit/s each. One of the timeslots is used for

synchronization, which means that 31 timeslots for an E‐1 or 23 timeslots for a T‐1,

respectively, can be used to transfer data. In practice, only 29 or 30 timeslots are used

for user data transmission while the rest (usually one or two) are used for SS‐7 signaling

data (see Figure1.3). More about SS‐7 can be found in Section1.4.

A single E‐1 connection with 31 DS0s is not enough to connect two switching centers

with each other. An alternative is an E‐3 connection over twisted pair or coaxial cables.

An E‐3 connection is defined at a speed of 34.368 Mbit/s, which corresponds to

512 DS0s.

For higher transmission speeds and for long distances, optical systems that use the

synchronous transfer mode (STM) standard are used. Table1.1 shows some datarates

and the number of 64 kbit/s DS0 channels that are transmitted per pair of fibers.

Table1.1 STM transmission speeds andnumber ofDS0s.

STM level Speed (Mbit/s)

Approximate number

of DS0 connections

STM‐1 155.52 2300

STM‐4 622.08 9500

STM‐16 2488.32 37,000

STM‐64 9953.28 148,279

Synchronization

31 timeslots with 8 bits (1B) each for user data o

SS-7 signaling

Repetition interval: 8000 Hz

Speed: 32 timeslots × 8 Bit × 8000 1/s=2.048 Mbit/s

Figure1.3 Timeslot architecture of an E‐1 connection.

From GSM to LTE-Advanced Pro and 5G

For virtual circuit switching over IP, optical Ethernet links are often used between

network nodes at the same location. Transmission speeds of 1 Gbit/s or more are

used on these links. Unlike the circuit‐switched technology described above,

Ethernet is the de facto standard for IP‐based communication over fiber and copper

cables and is widely used. As a consequence, network equipment can be built much

more cheaply.

1.4 The Signaling System Number 7

For establishing, maintaining and clearing a connection, signaling information needs to

be exchanged between the end user and network devices. In the fixed‐line network,

analog phones signal their connection request when the receiver is lifted off the hook

and a phone number dialed that is sent to the network either via pulses (pulse dialing)

or via tone dialing, which is called dual tone multifrequency (DTMF) dialing. With

fixed‐line ISDN phones and GSM mobile phones, the signaling is done via a separate

dedicated signaling channel, and information such as the destination phone number is

sent as messages.

If several components in the network are involved in the call establishment, for exam-

ple, if originating and terminating parties are not connected to the same switching

center, it is also necessary that the different nodes in the network exchange information

with each other. This signaling is transparent for the user, and a protocol called the SS‐7

is used for this purpose. SS‐7 is also used in GSM networks and the standard has been

enhanced by ETSI to fulfill the special requirements of mobile networks, for example,

subscriber mobility management.

The SS‐7 standard defines three basic types of network nodes:

● Service Switching Points (SSPs) are switching centers that are more generally referred

to as network elements and that are able to establish, transport or forward voice and

data connections.

● Service Control Points (SCPs) are databases and application software that can influ-

ence the establishment of a connection. In a GSM network, SCPs can be used, for

example, for storing the current location of a subscriber. During call establishment to

a mobile subscriber, the switching centers query the database for the current location

of the subscriber to be able to forward the call. More about this procedure can be

found in Section1.6.3 about the Home Location Register (HLR).

● Signaling Transfer Points (STPs) are responsible for the forwarding of signaling mes-

sages between SSPs and SCPs as not all network nodes have a dedicated link to all

other nodes of the network. The principal functionality of an STP can be compared

to an IP router in the Internet, which also forwards packets to different branches of

the network. Unlike IP routers, however, STPs only forward signaling messages that

are necessary for establishing, maintaining and clearing a call. The calls themselves

are directly carried on dedicated links between the SSPs.

Figure1.4 shows the general structure of an SS‐7 circuit‐switched telecommunication

network and the way the nodes described above are interconnected with each other.

The SS‐7 protocol stack is also used in virtual circuit‐switched networks for com-

munication between the network nodes. Instead of dedicated signaling timeslots on an

剩余536页未读，继续阅读

bigpapaya

粉丝: 1
资源: 2

移动网络与宽带入门：从GSM到LTE-Advanced Pro和5G

LTE-advanced pro and the road to 5G

深入理解lte-a 温金辉 书籍

除了4G、5G，LTE还有什么相关技术呢？

深入理解lte-a pdf

LTE-M operate on the LTE band 其中LTE-M是什么 LTE-band是什么

lte-a中载波聚合 matlab

WH-LTE-7S1特点

LTE-V技术和DSRC技术比较

lte-及5g-nr高铁场景网络优化

LTE-V2X关键技术

lte matlab

怎么在GitHub上获取使用matlab的LTE用户到基站协议的建模仿真例程

LTE-V2X空口时延

lte-v2x 和nr v2x区别

LTE-V2X通信技术

lte-v2x通信模组

LTE-M技术在城市轨道交通中的实际应用案例

最新资源

深入理解lte-a 温金辉书籍