没有合适的资源?快使用搜索试试~ 我知道了~
首页aspeed AST2500/AST2520 v16带水印 datasheet
资源详情
资源推荐
AST2500/AST2520
Integrated Remote Management Processor
A2 Datasheet
Version 1.6
May 12, 2017
ASPEED Technology Inc. retains the right to make changes to its products or specifications. While
the information furnished herein is held to be accurate and reliable, no responsibility will be assumed
by ASPEED Technology for its use. Furthermore, the information contained herein does not convey to
the purchaser of microelectronic devices any license under the patent right of any manufactures.
ASPEED products are not intended for use in life support products where failure of an ASPEED product
could reasonably be expected to result in death or personal injury. Anyone using an ASPEED product
in such an application without express written consent of an officer of ASPEED does so at their own
risk, and agrees to fully indemnify ASPEED for any damages that may result from such use or sale.
All other trademarks or register trademarks mentioned herein are the property of their respective
holders.
Headquarters
2F,No.15,Industry East Road 4.,Hsinchu Science Park,
Hsinchu City 30077, Taiwan, R. O. C.
TEL: 886-3-5789568
FAX: 886-3-5789586
http://www.ASPEEDtech.com
Copyright
c
2017, ASPEED Technology Inc. All right reserved.
ASPEED AST2500/AST2520 A2 Datasheet – V1.6
Ordering Information
Part number :AST2500A2 - GP
Solder ball type :Lead-free
Substrate type :RoHS Green package
Package size :19mm x 19mm
Ball pitch : 0.8mm
ASPEED
AST2500
XXXXXX.XXXXXX
YYWW TAN A2 GP
Topside mark
Part number :AST2520A2 - GP
Solder ball type :Lead-free
Substrate type :RoHS Green package
Package size :19mm x 19mm
Ball pitch : 0.8mm
ASPEED
AST2520
XXXXXX.XXXXXX
YYWW TAN A2 GP
Topside mark
Top Marking Definition:
Line 1: [ASPEED] = Company Logo
Line 2: [ASTxxxx] = Product Code
Line 3: [XXXXXX.XXXXXX] = IC Foundry Lot Number
Line 4: [YYWW] = Date code, [TAN], [xx] = Chip Revision Number, [GP] = RoHS
ASPEED Confidential All rights reserved. 2 M
ay 12, 2017
ASPEED AST2500/AST2520 A2 Datasheet – V1.6
Revision History
Date Revision Description
Jul. 04, 2014 0.1 Initial draft.
Jan. 22, 2015 0.9 1. Release for chip revision A1.
2. Add chip revision A1 migration list at next page.
3. Add per-pin function configuration table at Section 5.3.
4. Add Reset Source Table at Section 6.
5. Add USB ports configuration mode description at Section 1.8.5.
6. Add Firmware update methods description at Section 1.9.
7. Add Firmware boot up sequence diagram at Section 10.
8. Revise IV11D from 1.1V to 1.15V.
9. Add ESD specification.
10. Revise DACRSET external resistor value to 18KΩ.
Jun. 22, 2015 1.0 1. Add CMOS IO 2.5V/1.8V DC spec.
2. Add feature of PCI-Express Master.
3. Rename power ball T11 from PV33D to MPLLAV33, this power ball
requires isolated power rail with low noise.
4. Add specification for overshoot, undershoot, and ringback at section 3.3.
5. Add power consumption information at section 3.6.
6. Add DC electrical specification for DDR, USB, BSRAM at section 3.9.
7. Add AC electrical specification at section 3.10.
8. Add thermal specification at section 3.11.
9. Update firmware programming note at section 9.
10. Update the timing waveform of SGPIO master at section 2.6.1.
11. Add verilog example of SGPIO shifter at section 2.6.2.
12. Revise the pull up power of MAC TX strap pins.
13. Revise some values in the power up sequence at section 3.7.
Oct. 15, 2015 1.1 1. Revise boot up sequence diagram at section 10.
2. Add registers specification of APB to PCIe Bus Bridge at section 30.
3. Add registers specification of PCIe Host Controller at section 51.
4. Add firmware related APnote of Application Note 1 and
Application Note 2.
5. Add hardware related APnote or Application Note 3.
6. Rename ”Graphics Display Controller” to ”SOC Display Controller”.
7. Remove ”Graphics Display Controller” feature on AST2520.
8. Add architecture block diagram of AST2520 at Figure-2.
Mar. 30, 2016 1.2 1. Release for chip revision A2.
2. Fix eSPI SUART1/SUART2 IRQ number issue.
3. Update chip hardware revision ID at SCU7C.
May. 18, 2016 1.3 1. Revise ADC DC specification.
2. Add power down sequence for firmware at section 3.8.
Jun. 07, 2016 1.31 1. Revise power down sequence for firmware at section 3.8. AST2510 do not
require to care the power down sequence.
Nov. 08, 2016 1.4 1. Revise reset function of SPI1/SPI2 controller at section 6.2.
2. Remove MACD0 and MACD4 at section 16. Please refer document E2500-
01 or Errata List.
3. Relax AC timing rise/fall time specification of RGMII, SPI, and eSPI.
4. Add recommended operating temperature of T
C
.
Jan. 09, 2017 1.5 1. Add Strap input pins AC timing specification at section 3.10.15.
2. Remove USB portB USB2.0 Device Controller feature. Please refer docu-
ment E2500-02 or Errata List.
May. 12, 2017 1.6 1. Revise SPI master AC timing specification at section 3.10.7.
2
. Revise eSPI AC timing specification at section 3.10.8.
3
. Revise I2C AC timing specification at section 3.10.11.
to next page
ASPEED Confidential All rights reserved. 3 M
ay 12, 2017
ASPEED AST2500/AST2520 A2 Datasheet – V1.6
from previous page
4. Revise Overshoot timing specification at section 3.3.
5. Add MDC/MDIO AC timing specification at section 3.10.3.
Text color definition
1. All new added features compare to AST2400/AST1250/AST1400 are highlighted by this color.
2. All different contents compare to previous release are highlighted by this color.
3. All important descriptions are highlighted by this color.
4. Removed features are highlighted by this style.
AST2500 Migration List from A1 to A2
Functional Bugs in A1 that have fixed in A2 list
1. Fix eSPI SUART1/SUART2 IRQ number issue, change from 7/8 to 4/3.
ASPEED Confidential All rights reserved. 4 M
ay 12, 2017
ASPEED AST2500/AST2520 A2 Datasheet – V1.6
AST2500 - A2 Errata List
1. In Ethernet MAC controller IP, there are totally 8 MAC address filters, the MAC address filter #4 can not
work properly, the affected registers are MACD0 and MACD4.
• Solution: There is no hardware or software solution for this issue. Please do not use this MAC
address filter #4. Instead, please use the other 7 MAC address filters if you need to filter certain
MAC address.
2. In USB port B function – USB2.0 device controller, there is a logic failure on device address identification,
thus it can not identify the correct device address and respond wrong packets to the host.
• Solution: There is no hardware or software solution for this issue. Please do not use USB port B
device controller function.
ASPEED Confidential All rights reserved. 5 M
ay 12, 2017
剩余832页未读,继续阅读
_阿桂_
- 粉丝: 105
- 资源: 35
上传资源 快速赚钱
- 我的内容管理 收起
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
会员权益专享
最新资源
- VMP技术解析:Handle块优化与壳模板初始化
- C++ Primer 第四版更新:现代编程风格与标准库
- 计算机系统基础实验:缓冲区溢出攻击(Lab3)
- 中国结算网上业务平台:证券登记操作详解与常见问题
- FPGA驱动的五子棋博弈系统:加速与创新娱乐体验
- 多旋翼飞行器定点位置控制器设计实验
- 基于流量预测与潮汐效应的动态载频优化策略
- SQL练习:查询分析与高级操作
- 海底数据中心散热优化:从MATLAB到动态模拟
- 移动应用作业:MyDiaryBook - Google Material Design 日记APP
- Linux提权技术详解:从内核漏洞到Sudo配置错误
- 93分钟快速入门 LaTeX:从入门到实践
- 5G测试新挑战与罗德与施瓦茨解决方案
- EAS系统性能优化与故障诊断指南
- Java并发编程:JUC核心概念解析与应用
- 数据结构实验报告:基于不同存储结构的线性表和树实现
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功