没有合适的资源?快使用搜索试试~ 我知道了~
首页1、PCI Local Bus Specification R3.0.pdf
PCI Local Bus Specification 3.0 The PCI Local Bus is a high performance 32-bit or 64-bit bus with multiplexed address and data lines. The bus is intended for use as an interconnect mechanism between highly integrated peripheral controller components, peripheral add-in cards, and processor/memory systems. The PCI Local Bus Specification, Rev. 3.0, includes the protocol, electrical, mechanical, and configuration specification for PCI Local Bus components and add-in cards. The electrical definition provides for the 3.3V signaling environmen
资源详情
资源评论
资源推荐

PCI Local Bus Specification
Revision 3.0
February 3, 2004

PCI LOCAL BUS SPECIFICATION, REV. 3.0
2
REVISION REVISION HISTORY DATE
1.0 Original issue. 6/22/92
2.0 Incorporated connector and add-in card specification. 4/30/93
2.1 Incorporated clarifications and added 66 MHz chapter. 6/1/95
2.2 Incorporated ECNs and improved readability. 12/18/98
2.3 Incorporated ECNs, errata, and deleted 5 volt only keyed
add-in cards.
3/29/02
3.0 Incorporated ECNs, errata, and removed support for the
5.0 volt keyed system board connector. Moved the
Expansion ROM description to the PCI Firmware
Specification.
2/3/04
PCI-SIG disclaims all warranties and liability for the use of this document and the
information contained herein and assumes no responsibility for any errors that may appear
in this document, nor does PCI-SIG make a commitment to update the information
contained herein.
Contact the PCI-SIG office to obtain the latest revision of the specification.
Questions regarding this PCI specification or membership in PCI-SIG may be forwarded to:
PCI-SIG
5440 SW Westgate Drive
Suite 217
Portland, Oregon 97221
Phone: 503-291-2569
Fax: 503-297-1090
e-mail administration@pcisig.com
http://www.pcisig.com
DISCLAIMER
This PCI Local Bus Specification is provided "as is" with no warranties whatsoever,
including any warranty of merchantability, noninfringement, fitness for any particular
purpose, or any warranty otherwise arising out of any proposal, specification, or sample.
PCI-SIG disclaims all liability for infringement of proprietary rights, relating to use of
information in this specification. No license, express or implied, by estoppel or otherwise,
to any intellectual property rights is granted herein.
PCI Express is a trademark of PCI-SIG.
All other product names are trademarks, registered trademarks, or servicemarks of their
respective owners.
Copyright © 1992, 1993, 1995, 1998, and 2004 PCI-SIG

PCI LOCAL BUS SPECIFICATION, REV. 3.0
3
Contents
PREFACE ........................................................................................................................ 13
S
PECIFICATION
............................................................................................................... 13
I
NCORPORATION OF
E
NGINEERING
C
HANGE
N
OTICES
(ECN
S
)....................................... 13
D
OCUMENT
C
ONVENTIONS
............................................................................................ 14
1. INTRODUCTION................................................................................................... 15
1.1. S
PECIFICATION
C
ONTENTS
................................................................................. 15
1.2. M
OTIVATION
...................................................................................................... 15
1.3. PCI L
OCAL
B
US
A
PPLICATIONS
......................................................................... 16
1.4. PCI L
OCAL
B
US
O
VERVIEW
............................................................................... 17
1.5. PCI L
OCAL
B
US
F
EATURES AND
B
ENEFITS
........................................................ 18
1.6. A
DMINISTRATION
............................................................................................... 20
2. SIGNAL DEFINITION .......................................................................................... 21
2.1. S
IGNAL
T
YPE
D
EFINITION
.................................................................................. 22
2.2. P
IN
F
UNCTIONAL
G
ROUPS
.................................................................................. 22
2.2.1. System Pins................................................................................................ 23
2.2.2. Address and Data Pins.............................................................................. 24
2.2.3. Interface Control Pins............................................................................... 25
2.2.4. Arbitration Pins (Bus Masters Only) ........................................................ 27
2.2.5. Error Reporting Pins................................................................................. 27
2.2.6. Interrupt Pins (Optional) .......................................................................... 28
2.2.7. Additional Signals ..................................................................................... 31
2.2.8. 64-Bit Bus Extension Pins (Optional) ....................................................... 33
2.2.9. JTAG/Boundary Scan Pins (Optional)...................................................... 34
2.2.10. System Management Bus Interface Pins (Optional) ................................. 35
2.3. S
IDEBAND
S
IGNALS
............................................................................................ 36
2.4. C
ENTRAL
R
ESOURCE
F
UNCTIONS
....................................................................... 36
3. BUS OPERATION.................................................................................................. 37
3.1. B
US
C
OMMANDS
................................................................................................ 37
3.1.1. Command Definition ................................................................................. 37
3.1.2. Command Usage Rules ............................................................................. 39
3.2. PCI P
ROTOCOL
F
UNDAMENTALS
....................................................................... 42
3.2.1. Basic Transfer Control.............................................................................. 43
3.2.2. Addressing................................................................................................. 44
3.2.3. Byte Lane and Byte Enable Usage ............................................................ 56
3.2.4. Bus Driving and Turnaround .................................................................... 57
3.2.5. Transaction Ordering and Posting ........................................................... 58
3.2.6. Combining, Merging, and Collapsing....................................................... 62

PCI LOCAL BUS SPECIFICATION, REV. 3.0
4
3.3. B
US
T
RANSACTIONS
........................................................................................... 64
3.3.1. Read Transaction ...................................................................................... 65
3.3.2. Write Transaction...................................................................................... 66
3.3.3. Transaction Termination........................................................................... 67
3.4. A
RBITRATION
..................................................................................................... 87
3.4.1. Arbitration Signaling Protocol.................................................................. 89
3.4.2. Fast Back-to-Back Transactions ............................................................... 91
3.4.3. Arbitration Parking................................................................................... 94
3.5. L
ATENCY
............................................................................................................ 95
3.5.1. Target Latency........................................................................................... 95
3.5.2. Master Data Latency................................................................................. 98
3.5.3. Memory Write Maximum Completion Time Limit.....................................99
3.5.4. Arbitration Latency ................................................................................. 100
3.6. O
THER
B
US
O
PERATIONS
................................................................................. 110
3.6.1. Device Selection ...................................................................................... 110
3.6.2. Special Cycle ........................................................................................... 111
3.6.3. IDSEL Stepping....................................................................................... 113
3.6.4. Interrupt Acknowledge ............................................................................ 114
3.7. E
RROR
F
UNCTIONS
........................................................................................... 115
3.7.1. Parity Generation.................................................................................... 115
3.7.2. Parity Checking....................................................................................... 116
3.7.3. Address Parity Errors ............................................................................. 116
3.7.4. Error Reporting....................................................................................... 117
3.7.5. Delayed Transactions and Data Parity Errors ....................................... 120
3.7.6. Error Recovery........................................................................................ 121
3.8. 64-B
IT
B
US
E
XTENSION
................................................................................... 123
3.8.1. Determining Bus Width During System Initialization............................. 126
3.9. 64-
BIT
A
DDRESSING
......................................................................................... 127
3.10. S
PECIAL
D
ESIGN
C
ONSIDERATIONS
.............................................................. 130
4. ELECTRICAL SPECIFICATION...................................................................... 137
4.1. O
VERVIEW
....................................................................................................... 137
4.1.1. Transition Road Map .............................................................................. 137
4.1.2. Dynamic vs. Static Drive Specification ................................................... 138
4.2. C
OMPONENT
S
PECIFICATION
............................................................................ 139
4.2.1. 5V Signaling Environment ...................................................................... 140
4.2.2. 3.3V Signaling Environment ................................................................... 146
4.2.3. Timing Specification................................................................................ 150
4.2.4. Indeterminate Inputs and Metastability .................................................. 155
4.2.5. Vendor Provided Specification................................................................ 156
4.2.6. Pinout Recommendation ......................................................................... 157

PCI LOCAL BUS SPECIFICATION, REV. 3.0
5
4.3. S
YSTEM
B
OARD
S
PECIFICATION
....................................................................... 158
4.3.1. Clock Skew .............................................................................................. 158
4.3.2. Reset ........................................................................................................ 158
4.3.3. Pull-ups ................................................................................................... 161
4.3.4. Power ...................................................................................................... 163
4.3.5. System Timing Budget ............................................................................. 164
4.3.6. Physical Requirements ............................................................................ 167
4.3.7. Connector Pin Assignments .................................................................... 168
4.4. A
DD
-
IN
C
ARD
S
PECIFICATION
.......................................................................... 171
4.4.1. Add-in Card Pin Assignment................................................................... 171
4.4.2. Power Requirements ............................................................................... 176
4.4.3. Physical Requirements ............................................................................ 178
5. MECHANICAL SPECIFICATION.................................................................... 181
5.1. O
VERVIEW
....................................................................................................... 181
5.2. A
DD
-
IN
C
ARD
P
HYSICAL
D
IMENSIONS AND
T
OLERANCES
............................... 182
5.3. C
ONNECTOR
P
HYSICAL
D
ESCRIPTION
.............................................................. 195
5.4. C
ONNECTOR
P
HYSICAL
R
EQUIREMENTS
.......................................................... 205
5.5. C
ONNECTOR
P
ERFORMANCE
S
PECIFICATION
.................................................... 206
5.6. S
YSTEM
B
OARD
I
MPLEMENTATION
.................................................................. 207
6. CONFIGURATION SPACE .................................................................................. 213
6.1. C
ONFIGURATION
S
PACE
O
RGANIZATION
.......................................................... 213
6.2. C
ONFIGURATION
S
PACE
F
UNCTIONS
................................................................ 216
6.2.1. Device Identification ............................................................................... 216
6.2.2. Device Control ........................................................................................ 217
6.2.3. Device Status ........................................................................................... 219
6.2.4. Miscellaneous Registers.......................................................................... 221
6.2.5. Base Addresses........................................................................................ 224
6.3. PCI E
XPANSION
ROM
S
................................................................................... 228
6.4. V
ITAL
P
RODUCT
D
ATA
..................................................................................... 229
6.5. D
EVICE
D
RIVERS
.............................................................................................. 229
6.6. S
YSTEM
R
ESET
................................................................................................. 230
6.7. C
APABILITIES
L
IST
........................................................................................... 230
6.8. M
ESSAGE
S
IGNALED
I
NTERRUPTS
.................................................................... 231
6.8.1. MSI Capability Structure ........................................................................ 232
6.8.2. MSI-X Capability and Table Structures .................................................. 238
6.8.3. MSI and MSI-X Operation ...................................................................... 246
7. 66 MHZ PCI SPECIFICATION.......................................................................... 255
7.1. I
NTRODUCTION
................................................................................................. 255
7.2. S
COPE
............................................................................................................... 255
7.3. D
EVICE
I
MPLEMENTATION
C
ONSIDERATIONS
.................................................. 255
7.3.1. Configuration Space................................................................................ 255
7.4. A
GENT
A
RCHITECTURE
.................................................................................... 256
剩余343页未读,继续阅读














weixin_44732087
- 粉丝: 0
- 资源: 5
上传资源 快速赚钱
我的内容管理 收起
我的资源 快来上传第一个资源
我的收益
登录查看自己的收益我的积分 登录查看自己的积分
我的C币 登录后查看C币余额
我的收藏
我的下载
下载帮助

会员权益专享
最新资源
- ARM Cortex-A(armV7)编程手册V4.0.pdf
- ABB机器人保养总结解析.ppt
- 【超详细图解】菜鸡如何理解双向链表的python代码实现
- 常用网络命令的使用 ipconfig ping ARP FTP Netstat Route Tftp Tracert Telnet nslookup
- 基于单片机控制的DC-DC变换电路
- RS-232接口电路的ESD保护.pdf
- linux下用time(NULL)函数和localtime()获取当前时间的方法
- Openstack用户使用手册.docx
- KUKA KR 30 hA,KR 60 hA机器人产品手册.pdf
- Java programming with JNI
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈



安全验证
文档复制为VIP权益,开通VIP直接复制

评论0