Datalogic Matrix 120™ 参考手册

需积分: 13 66 浏览量更新于2024-07-17 收藏 8.68MB PDF 举报

"MATRIX 120™ 参考手册提供了DATALOGIC MATRIX 120™的详细技术信息，由Datalogic Automation S.r.l.出版。手册版本为11/2016，强调了所有版权保护，未经Datalogic S.p.A.的书面同意，禁止复制或修改。手册中包含的技术和编辑错误或遗漏，Datalogic不承担责任，且与使用此材料相关的间接或附带损害也不在赔偿范围内。" 《MATRIX 120™ 参考手册》是Datalogic公司为用户提供的一款详细的操作和技术指南，主要针对DATALOGIC MATRIX 120™这款产品。DATALOGIC MATRIX 120™可能是该公司的一款高级工业扫描器或视觉传感器，用于自动化识别和数据采集。在手册中，"参考资料"部分可能包括了对设备操作、设置、维护和故障排查的详细说明。"约定"章节会定义手册中使用的符号和术语，以便读者能够正确理解内容。"参考文档"可能会提供其他相关的技术资料，如用户指南、安装手册或者API文档，以支持用户更全面地了解和使用MATRIX 120™。 "支持通过网站"部分可能介绍了如何访问Datalogic的官方网站获取额外支持和服务，用户可以通过这个平台获取软件更新、常见问题解答（FAQs）、在线论坛和客户服务联系信息等。 "专利"章节可能列出了与MATRIX 120™相关的专利信息，表明产品的创新性和知识产权的保护。 "合规性"部分是关于设备满足的各种法规和标准的说明。"EMC合规"指的是电磁兼容性，意味着该设备在电磁环境中不会干扰其他设备，同时也能抵抗外部电磁干扰。"电源合规"可能涉及到电源输入、功耗和安全标准。"CE合规"表明产品符合欧洲经济区的健康、安全和环保规定。"FCC合规"是指符合美国联邦通信委员会（FCC）的无线电频率排放规定，以防止无线电波干扰。而"EAC合规"则意味着产品符合欧亚经济联盟的认证要求。 "激光安全"部分将详细阐述MATRIX 120™中可能涉及的激光技术的安全标准和操作注意事项，确保用户在使用过程中能遵循必要的安全措施，避免激光辐射对人体造成潜在危害。《MATRIX 120™ 参考手册》是用户全面了解和有效使用DATALOGIC MATRIX 120™的必备参考资料，涵盖了从设备操作到法规遵从的全方位信息。

MATRIX 120™ REFERENCE MANUAL

CBX100/CBX500 Pinout for Matrix 120

The table below gives the pinout of the CBX100/CBX500 terminal block connectors. Use this

pinout only when the Matrix 120 reader is connected to the CBX100/CBX500 by means of

the CAB-1011 accessory cable:

CBX100/500 Terminal Block Connectors

Input Power

Vdc

Power Supply Input Voltage +

GND

Power Supply Input Voltage -

Earth

Protection Earth Ground

Inputs

Power Source – External Trigger

I1A

External Trigger A (polarity insensitive)

I1B

External Trigger B (polarity insensitive)

-V

Power Reference – External Trigger

Power Source – Inputs

I2A

Input 2 A (polarity insensitive)

I2B

Input 2 B (polarity insensitive)

-V

Power Reference – Inputs

Outputs

Power Source - Outputs

-V

Power Reference - Outputs

O1+

Output 1 + opto-isolated and polarity sensitive

O1-

Output 1 - opto-isolated and polarity sensitive

O2+

Output 2 + opto-isolated and polarity sensitive

O2-

Output 2 - opto-isolated and polarity sensitive

Auxiliary Interface

Matrix 120 has no Auxiliary Interface

ID-NET

Matrix 120 has no ID-NET Interface

Shield

Cable shield connected to chassis and 17-pin connector shell

Main Interface

RS232

RS422 Full-Duplex

TX+

*RX+

TX-

*RX-

SGND

* Do not leave floating, see par. 4.2.2 for connection details.

CAUTION: Do not connect GND and SGND to different (external) ground

references. GND and SGND are internally connected through filtering circuitry

which can be permanently damaged if subjected to voltage drops over 0.8

Vdc.

RAPID CONFIGURATION

Setup

1. Enter the Setup function by pressing and holding

the X-PRESS push button until the Setup LED is

on.

2. Release the button to enter the Setup function.

The Setup LED will blink until the procedure is

completed.

The Setup procedure ends when the Image

Acquisition parameters are successfully saved in

the reader memory, the Setup LED will stop

blinking and Matrix 120 emits 3 high pitched beeps.

If the calibration cannot be reached after a timeout

of about 5 (five) seconds Matrix 120 will exit without

saving the parameters to memory, the Setup LED

will stop blinking and in this case Matrix 120 emits a

long low pitched beep.

Figure 8 – X-PRESS Interface: Setup

Function

Learn

3. Enter the Learn function by pressing and holding

the X-PRESS push button until the Learn LED is

on.

4. Release the button to enter the Learn function.

The Learn LED will blink until the procedure is

completed.

The Learn procedure ends when the Image

Processing and Decoding parameters for a single

code are successfully saved in the reader

memory, the Green Spot is activated, the Learn

LED will stop blinking, and Matrix 120 emits 3 high

pitched beeps

If the autolearning cannot be reached after a

timeout of about 3 (three) minutes Matrix 120 will

exit without saving the parameters to memory, the

Learn LED will stop blinking and in this case Matrix

120 emits a long low pitched beep.

Figure 9 – X-PRESS Interface: Learn

Function

NOTE: The Grade A Barcode Test Chart cannot be used to set the Code

128 symbology (even though the reader successfully reads the code). Use

the application specific code if you need to set this symbology.

NOTE: When using X-PRESS or the BM150 menu to perform the Auto-learn,

only a single code can be configured (successive Learns will substitute the

current code). To configure multiple codes, use the DL.CODE Auto-learn

procedure.

The Learn procedure will not recognize the following symbologies: Postal Codes, Pharmacode, MSI, Standard 2 of 5,

Matrix 2 of 5.

剩余143页未读，继续阅读

「已注销」

粉丝: 0
资源: 1

Datalogic Matrix 120™ 参考手册

datalogic MATRIX 120N说明书

Matrix各种操作手册

MATRIX加工中心操作说明书

matrix 120说明书

得利捷固定扫码器Matrix120如何设置为socket服务端实时发送扫码数据

logPredictions <- ifelse(logPredictions > 0.5, "Up", "Down") confusionMatrix(data = logPredictions, reference = testingData$Direction)报错Error: data and reference should be factors with the same levels.

请创建一个函数 matrix_addition(A, B)，该函数接受两个 NumPy 数组（矩阵）作为输入，并返回它们的和，尝试自己使用循环计算而不是Numpy的内置运算。\ 再使用 NumPy 的内置函数来完成这个任务。\

R中confusionMatrix(trainY, train.probs) Error: `data` and `reference` should be factors with the same levels.

> confusionMatrix(data = rfPredictions$class, reference = testingData$Direction) Error in rfPredictions$class : $ operator is invalid for atomic vectors

r语言caret包confusionmatrix

最新资源