MSP430 LaunchPad入门教程与实验室手册简介

LaunchPad

4星 · 超过85%的资源需积分: 9 198 浏览量更新于2024-07-28 收藏 13.26MB PDF 举报

身份认证购VIP最低享 7 折!

30元优惠券

"《MSP430 LaunchPad入门指南与实验室手册修订版2.01》是一份专为学生设计的技术培训文档，发布于2012年2月。该文档是针对德州仪器（TI）的MSP430 LaunchPad平台的，旨在帮助用户快速上手并进行实验操作。LaunchPad是一款针对微控制器MSP430系列开发的低成本、易用的硬件平台，特别适合初学者入门学习。重要通知部分强调了TI及其子公司保留随时修改产品规格、停止产品供应或更新相关信息的权利。在购买前，用户必须确保获取最新版本的信息，以验证其适用性和完整性。所有产品销售都受当时订单确认时提供的销售条款和条件约束，包括保修政策、专利侵权责任限制和责任限制等。 TI对其半导体产品的性能提供保修，保证在售出时符合相关标准。然而，公司并非对每个设备的所有参数进行全面测试，除非政府有强制性规定。这意味着用户在使用时需要自行完成必要的验证和测试，以确保设备在实际应用中的性能满足预期。《MSP430 LaunchPad入门指南》可能包含以下内容： 1. 平台介绍：对LaunchPad硬件构成、接口和功能的详细介绍，包括电源管理、编程接口、调试器等关键组件。 2. 安装与配置：指导用户如何连接和配置开发环境，如使用IAR Embedded Workbench、Keil μVision等IDE。 3. 基础编程：通过示例代码教授C语言和汇编语言编程，以及如何编写和调试MSP430程序。 4. 传感器和外设：介绍如何使用LaunchPad上的传感器模块，如温度、光照、加速度计等，并实现数据采集和处理。 5. 项目实践：提供一系列项目案例，从简单的LED闪烁到更复杂的控制系统，帮助用户逐步掌握实际应用技巧。 6. 故障排查与调试：讲解常见问题的识别和解决方法，以及如何有效利用调试工具定位和修复错误。 7. 安全注意事项：强调在使用过程中应遵循的安全规范，如静电防护和电源管理等。这份指南是学习MSP430开发的理想起点，无论是作为个人学习资料还是课堂教程，都能为初学者提供一个清晰的学习路径和实践经验。"

资源详情

资源推荐

Lab 1: Download Software and Setup Hardware

1 - 14 Getting Started with the MSP430 LaunchPad - Introduction to Value Line

Download Supporting Documents and Software

14. Windows7 no longer has HyperTerminal. To regain that capability, download and

“install”

TeraTerm or another terminal program of your choice.

15. Next, download and save the following documents and software to your computer:

• LaunchPad User’s Guide: http://www.ti.com/lit/slau318

• MSP430x2xx User’s Guide: http://www.ti.com/lit/slau144

• C Compiler User’s Guide http://www.ti.com/lit/slau132

• MSP430G2xx code examples: http://www.ti.com/lit/zip/slac463

• Temperature demo source and GUI: http://www.ti.com/lit/zip/slac435

• A copy of the workshop workbook pdf: http://www.ti.com/launchpad-workshop

Additional information:

www.ti.com/launchpadwiki

www.ti.com/launchpad

www.ti.com/captouch

Third Party Websites

16. There are many, many third party MSP430 websites out there. A couple of good ones are:

http://www.joesbytes.com

http://www.mspoh.com

Lab 1: Download Software and Setup Hardware

Getting Started with the MSP430 LaunchPad - Introduction to Value Line 1 - 15

MSP-EXP430G2 LaunchPad Experimenter Board

The MSP-EXP430G2 is a low-cost experimenter board, also known as LaunchPad. It

provides a complete development environment that features integrated USB-based emulation

and all of the hardware and software necessary to develop applications for the MSP430G2xx

Value Line series devices.

17. Look on the side of your LaunchPad kit and find the revision number. At the time this

workshop was written, version 1.5 is the current version. The steps in this workshop will

cover both the 1.4 and 1.5 revisions.

Open the MSP430 LaunchPad kit box and inspect the contents. The kit includes:

• LaunchPad emulator socket board (MSP-EXP430G2)

• Mini USB-B cable

• In the Revision 1.5 kit…

A MSP430G2553 (pre-installed and pre-loaded with demo program) and

a MSP430G2452

• In the Revision 1.4 kit…

A MSP430G2231 (pre-installed and pre-loaded with demo program) and

a MSP430G2211

• In the Revision 1.5 kit…

10-pin PCB connectors are soldered to the board and two female also

included

• In the Revision 1.4 kit…

Two male and two female 10-pin PCB connectors

• 32.768 kHz micro crystal

• Quick start guide and two LaunchPad stickers

Hardware Setup

The LaunchPad experimenter board includes a pre-programmed MSP430 device which is

already located in the target socket. When the LaunchPad is connected to your PC via USB,

the demo starts with an LED toggle sequence. The on-board emulator generates the supply

voltage and all of the signals necessary to start the demo.

18. Connect the MSP430 LaunchPad to your PC using the included USB cable. The driver

installation starts automatically. If prompted for software, allow Windows to install the

software automatically.

19. At this point, the on-board red and green LEDs should toggle back and forth. This lets us

know that the hardware is working and has been set up correctly.

Lab 1: Download Software and Setup Hardware

1 - 16 Getting Started with the MSP430 LaunchPad - Introduction to Value Line

Running the Application Demo Program

The pre-programmed application demo takes temperature measurements using the internal

temperature sensor. This demo exercises the various on-chip peripherals of the MSP430

device and can transmit the temperature via UART to the PC for display.

20. Press button P1.3 (lower-left) to switch the application to the temperature measurement

mode. A temperature reference is taken at the beginning of this mode and the LEDs on

the LaunchPad signal a rise or fall in temperature by varying the brightness of the on-

board red LED for warmer or green LED for colder.

Rub your fingertip on your pants to warm it up and place it on the top of the MSP430

device on the LaunchPad board. After a few seconds the red Led should start to light,

indicating a temperature rise. When the red LED is solidly lit, remove your finger and

press button P1.3 again. This will set the temperature reference at the higher temperature.

As the part cools, the green LED will light, indicating decreasing temperature. Bear in

mind that ambient temperatures will affect this exercise.

21. Next we will be using the GUI to display the temperature readings on the PC. Be sure

that you have installed the downloaded GUI source files (LaunchPad_Temp_GUI.zip).

22. Determine the COM port used for the board by clicking (in Windows XP) Start  Run

then type devmgmt.msc in the box and select OK. (In Windows 7, just type

devmgmt.msc into the Search programs and files box)

In the Device Manager window that opens, left-click the symbol left of

Ports (COM & LPT) and record the COM port number for

MSP430 Applications UART (COMxx):________. Close the Device Manager.

23. Start the GUI by clicking on LaunchPad_Temp_GUI.exe. This file is found under

<Install Directory>\LaunchPad_Temp_GUI\application.window. You may have to select

Run in the “Open File – Security Warning” window.

24. It will take a few seconds for the GUI to start. Be sure that the MSP430 application is

running (i.e. button P1.3 has been pressed). In the GUI, select the COM port found in

step 16 and press Enter (this is a DOS window, your mouse will not work in it). The

current temperate should be displayed. Try increasing and decreasing the temperature on

the device and notice the display reading changes. Note that the internal temperature

sensor is not calibrated, so the reading displayed will not be accurate. We are just

looking for the temperature values to change.

25. Close the temperature GUI .

You’re done.

剩余175页未读，继续阅读

ch378584416

粉丝: 0
资源: 5

MSP430 LaunchPad入门教程与实验室手册简介

Analog and interface guide

tm4c123g入门使用

msp432学习资料

帮我找一些msp432p401r的rtos博客

isight入门教程

编写一个单片机msp430g2553的代码

MSP430g2553教程

MSP432环境配置

msp-exp432p401r 驱动

msp430编写环境

ccs配置msp432环境

python3.8下载安装教程

JAVA+access综合测评系统毕业设计(源代码+论文+开题报告+任务书).zip

33企业财务风险分析及防范——以永辉超市股份有限公司为例.docx

JAVA物业管理系统设计与实现(论文+源代码).zip

基于springboot的车辆充电桩管理系统设计与实现.docx

weixin196运动健康小程序SpringBoot.rar

开家可乐店bcm4文件

Zblog 的CDNfly-CloudFlare全能CDN自动刷新缓存插件-自动清理-适配优化2.1.0版本

ssm+mysql的在线投票系统（源码+lw+ppt）

最新资源