![](https://csdnimg.cn/release/download_crawler_static/86044168/bg5.jpg)
每个波特有 4 个合法值,因此比特率是波特率的两倍。对应于 1200 波特,数据速率是 2400bps。
2-28 Ten signals, each requiring 4000 Hz, are multiplexed on to a single channel using FDM. How much minimum bandwidth
is required for the multiplexed channel? Assume that the guard bands are 400 Hz wide.
有10个信号,每个都要求4000Hz,现在用FDM将它们复用在一条信道上。对于被复用的信道,最小要求多少带宽?假设防护频段为400Hz
宽。
有 10 个 4000Hz 信号。我们需要 9 个防护频段来避免干扰。最小带宽需求是 4000×10+400×9 =43,600 Hz.
2-29 Why has the PCM sampling time been set at 125 µsec?
答:125 的采样时间对应于每秒 8000 次采样。一个典型的电话通道为 4kHz。根据奈奎斯特定理,为获取一个 4kHz 的通道中的全
部信息需要每秒 8000 次的采样频率。
(实际上额定带宽稍有些少,截止点并不清晰)
2-30 What is the percent overhead on a T1 carrier; that is, what percent of the 1.544 Mbps are not delivered to the
end user?
每一帧中,端点用户使用 193 位中的 168(7*24)位,开销占 25(=193-168)位,因此开销比例等于 25/193=13%。
2-33 What is the difference, if any, between the demodulator part of a modem and the coder part of a codec? (After all,
both convert analog signals to digital ones.)
答:有。编码器接受任意的模拟信号,并从它产生数字信号。而解调器仅仅接受调制了的正弦(或余弦)波,产生数字信号。
2-34 A signal is transmitted digitally over a 4-kHz noiseless channel with one sample every 125 µsec. How many bits
per second are actually sent for each of these encoding methods?
(a) CCITT 2.048 Mbps standard. (b) DPCM with a 4-bit relative signal value. (c) Delta modulation.
答:a.CCITT 2.048Mbps 标准用 32 个 8 位数据样本组成一个 125 的基本帧,30 个信道用于传信息,2 个信道用于传控制信号。
在每一个 4kHz 信道上发送的数据率就是
8*8000=64kbps。
b.差分脉码调制(DPCM)是一种压缩传输信息量的方法,它发送的不是每一次抽样的二进制编码值,而是两次抽样的差值的二进制
编码。现在相对差值是 4 位,所以对应每个 4kHz 信道实际发送的比特速率为 4*8000=32bps。
c.增量调制的基本思想是:当抽样时间间隔 s t 很短时,模拟数据在两次抽样之间的变化很小,可以选择一个合适的量化值? 作为
阶距。把两次抽样的差别近似为不是增加一个?就是减少一个? 。这样只需用 1bit 二进制信息就可以表示一次抽样结果,而不会引
入很大误差。因此,此时对应每个 4kHz 信道实际发送的数据速率为 1*8000=8kHz。
2-39What is the essential difference between message switching and packet switching?
信息交换发送到数据单元可以是任意长度。分组交换有最大报文大小限制,任何大于限制的信息将被拆分成多个报文。
2-41 Three packet-switching networks each contain n nodes. The first network has a star topology with a central switch,
the second is a (bidirectional) ring, and the third is fully interconnected, with a wire from every node to every other
node. What are the best-, average-, and-worst case transmission paths in hops?
三个分组交换网络每个包含n个节点。第一个网络是一个星型拓扑结构,有一个中心交换机;第二个网络是一个双向环;第三个网络
是一个全连接结构,从任何一个节点到其他的节点都有一条线路。请问从传输路径的跳数来看,哪个最好?其次?最差?
答:The three networks have the following properties:
星型:最好为 2,最差为 2,平均为 2;
环型:最好为 1,最差为 n/2,平均为 n/4
如果考虑 n 为奇偶数,
则 n 为奇数时,最坏为(n-1)/2,平均为(n+1)/4
n 为偶数时,最坏为 n/2,平均为 n2/4(n�1) �
全连接:最好为 1,最差为 1,平均为 1。
2-42 Compare the delay in sending an x-bit message over a k-hop path in a circuit-switched network and in a (lightly
loaded) packet-switched network. The circuit setup time is s sec, the propagation delay is d sec per hop, the packet
size is p bits, and the data rate is b bps. Under what conditions does the packet network have a lower delay?