NXP i.MX6ULL处理器数据手册：高性能多媒体平台

需积分: 7 82 浏览量更新于2024-07-09 收藏 2.27MB PDF 举报

NXP Semiconductors的IMX6ULLCEC数据手册是关于NXP公司的一款高性能多媒体处理器系列的详细技术文档，适用于日益增长的连接设备市场。该处理器集成了先进的单核Cortex-A7内核，其工作频率高达900MHz，旨在提供出色的性能和高效能。IMX6ULL家族包括多个型号，如MCIMX6Y0DVM05AA、MCIMX6Y1DVM05AB等，采用塑料封装，包括两种不同的封装尺寸——MAPBGA14x14mm，0.8mm间距，以及MAPBGA9x9mm，0.5mm间距。该系列的特点在于其高度集成的功能，它结合了处理能力和多媒体处理能力，特别适合那些对功耗敏感但又需要强大计算性能的应用场景，如物联网设备、智能家居、消费电子等。NXP保留了对生产细节规格的变更权，这允许他们在不影响产品质量的前提下进行设计改进，以适应不断发展的市场需求。 i.MX6ULL处理器的架构设计旨在优化资源利用，确保在满足高效率的同时，能够支持实时操作系统(RTOS)和多种嵌入式应用。它的特性可能包括内存管理单元(MMU)，用于保护内存空间，提高数据安全性；高效的总线系统，支持高速数据传输；以及丰富的外设接口，如USB、UART、GPIO等，便于与其他硬件组件通信。此外，数据手册还详细列出了引脚布局图、供电需求、温度范围、工作电压、以及存储器配置等关键信息。用户可以从中找到启动指南、编程接口说明、中断管理、时钟管理等方面的技术细节，这对于开发基于IMX6ULL的嵌入式系统的工程师来说是非常重要的参考资料。 IMX6ULLCEC数据手册提供了全面深入的理解，使得设计者可以根据项目需求选择合适的型号，并且能够充分利用该处理器的强大功能和高效能，以构建出具有竞争力的解决方案。通过阅读和理解这份文档，开发者能够提升产品的性能，同时降低总体成本，加快产品上市时间。

i.MX 6ULL Applications Processors for Consumer Products, Rev. 1.3, 08/2018

16 NXP Semiconductors

Modules List

TSC Touch Screen Touch Controller With touch controller to support 4-wire and 5-wire

resistive touch panel.

TZASC Trust-Zone Address

Space Controller

Security The TZASC (TZC-380 by Arm) provides security

address region control functions required for intended

application. It is used on the path to the DRAM

controller.

UART1

UART2

UART3

UART4

UART5

UART6

UART7

UART8

UART Interface Connectivity

Peripherals

Each of the UARTv2 module supports the following

serial data transmit/receive protocols and

configurations:

• 7- or 8-bit data words, 1 or 2 stop bits, programmable

parity (even, odd or none)

• Programmable baud rates up to 5 Mbps.

• 32-byte FIFO on Tx and 32 half-word FIFO on Rx

supporting auto-baud

uSDHC1

uSDHC2

SD/MMC and SDXC

Enhanced Multi-Media

Card / Secure Digital Host

Controller

Connectivity

Peripherals

i.MX 6ULL specific SoC characteristics:

All four MMC/SD/SDIO controller IPs are identical and

are based on the uSDHC IP. They are:

• Fully compliant with MMC command/response sets

and Physical Layer as defined in the Multimedia Card

System Specification, v4.5/4.2/4.3/4.4/4.41/

including high-capacity (size > 2 GB) cards HC MMC.

• Fully compliant with SD command/response sets

and Physical Layer as defined in the SD Memory

Card Specifications, v3.0 including high-capacity

SDXC cards up to 2 TB.

• Fully compliant with SDIO command/response sets

and interrupt/read-wait mode as defined in the SDIO

Card Specification, Part E1, v3.0

Two ports support:

• 1-bit or 4-bit transfer mode specifications for SD and

SDIO cards up to UHS-I SDR104 mode (104 MB/s

max)

• 1-bit, 4-bit, or 8-bit transfer mode specifications for

MMC cards up to 52 MHz in both SDR and DDR

modes (104 MB/s max)

• 4-bit or 8-bit transfer mode specifications for eMMC

chips up to 200 MHz in HS200 mode (200 MB/s max)

However, the SoC level integration and I/O muxing logic

restrict the functionality to the following:

• Instances #1 and #2 are primarily intended to serve

as interfaces to on-board peripherals. These ports

are equipped with “Card detection” and “Write

Protection” pads and do not support hardware reset.

• All ports can work with 1.8 V and 3.3 V cards. There

are two completely independent I/O power domains

for Ports #1 and #2 in four bit configuration (SD

interface).

Table 2. i.MX 6ULL Modules List (continued)

Block Mnemonic Block Name Subsystem Brief Description

i.MX 6ULL Applications Processors for Consumer Products, Rev. 1.3, 08/2018

18 NXP Semiconductors

Modules List

3.1 Special Signal Considerations

Table 3 lists special signal considerations for the i.MX 6ULL processors. The signal names are listed in

alphabetical order.

The package contact assignments can be found in Section 6, Package Information and Contact

Assignments".” Signal descriptions are provided in the i.MX 6ULL Reference Manual (IMX6ULLRM).

Table 3. Special Signal Considerations

Signal Name Remarks

CCM_CLK1_P/

CCM_CLK1_N

One general purpose differential high speed clock Input/output is provided.

It can be used:

• To feed external reference clock to the PLLs and further to the modules inside SoC.

• To output internal SoC clock to be used outside the SoC as either reference clock or as a

functional clock for peripherals.

See the i.MX 6ULL Reference Manual (IMX6ULLRM) for details on the respective clock trees.

Alternatively one may use single ended signal to drive CLK1_P input. In this case corresponding

CLK1_N input should be tied to the constant voltage level equal 1/2 of the input signal swing.

Termination should be provided in case of high frequency signals.

After initialization, the CLK1 input/output can be disabled (if not used). If unused, either or both of

the CLK1_N/P pairs may remain unconnected.

RTC_XTALI/RTC_XTALO If the user wishes to configure RTC_XTALI and RTC_XTALO as an RTC oscillator, a 32.768 kHz

crystal, (100 k ESR, 10 pF load) should be connected between RTC_XTALI and RTC_XTALO.

Keep in mind the capacitors implemented on either side of the crystal are about twice the crystal

load capacitor. To hit the exact oscillation frequency, the board capacitors need to be reduced to

account for board and chip parasitics. The integrated oscillation amplifier is self biasing, but

relatively weak. Care must be taken to limit parasitic leakage from RTC_XTALI and RTC_XTALO

to either power or ground (>100 M). This will debias the amplifier and cause a reduction of startup

margin. Typically RTC_XTALI and RTC_XTALO should bias to approximately 0.5 V.

If it is desired to feed an external low frequency clock into RTC_XTALI the RTC_XTALO pin should

be remain unconnected or driven with a complimentary signal. The logic level of this forcing clock

should not exceed VDD_SNVS_CAP level and the frequency should be <100 kHz under typical

conditions.

In case when high accuracy real time clock are not required, system may use internal low

frequency ring oscillator. It is recommended to connect RTC_XTALI to GND and keep RTC_XTALO

unconnected.

XTALI/XTALO A 24.0 MHz crystal should be connected between XTALI and XTALO.

The crystal must be rated for a maximum drive level of 250 W. An ESR (equivalent series

resistance) of typical 80  is recommended. NXP BSP (board support package) software requires

24 MHz on XTALI/XTALO.

The crystal can be eliminated if an external 24 MHz oscillator is available in the system. In this

case, XTALO must be directly driven by the external oscillator and XTALI is not connected.

If this clock is used as a reference for USB, then there are strict frequency tolerance and jitter

requirements. See OSC24M chapter and relevant interface specifications chapters for details.

DRAM_VREF When using DDR_VREF with DDR I/O, the nominal reference voltage must be half of the

NVCC_DRAM supply. The user must tie DDR_VREF to a precision external resistor divider. Use a

1k 0.5% resistor to GND and a 1 k 0.5% resistor to NVCC_DRAM. Shunt each resistor with a

closely-mounted 0.1 µF capacitor.

To reduce supply current, a pair of 1.5 k 0.1% resistors can be used. Using resistors with

recommended tolerances ensures the ± 2% DDR_VREF tolerance (per the DDR3 specification) is

maintained when two DDR3 ICs plus the i.MX 6ULL are drawing current on the resistor divider.

Modules List

i.MX 6ULL Applications Processors for Consumer Products, Rev. 1.3, 08/2018

NXP Semiconductors 19

3.2 Recommended Connections for Unused Analog Interfaces

Table 5 shows the recommended connections for unused analog interfaces.

ZQPAD DRAM calibration resistor 240  1% used as reference during DRAM output buffer driver

calibration should be connected between this pad and GND.

GPANAIO This signal is reserved for NXP manufacturing use only. This output must remain unconnected.

JTAG_nnnn The JTAG interface is summarized in Table 4. Use of external resistors is unnecessary. However,

if external resistors are used, the user must ensure that the on-chip pull-up/down configuration is

followed. For example, do not use an external pull down on an input that has on-chip pull-up.

JTAG_TDO is configured with a keeper circuit such that the non-connected condition is eliminated

if an external pull resistor is not present. An external pull resistor on JTAG_TDO is detrimental and

should be avoided.

JTAG_MOD is referenced as SJC_MOD in the i.MX 6ULL reference manual. Both names refer to

the same signal. JTAG_MOD must be externally connected to GND for normal operation.

Termination to GND through an external pull-down resistor (such as 1 k) is allowed. JTAG_MOD

set to hi configures the JTAG interface to mode compliant with IEEE1149.1 standard. JTAG_MOD

set to low configures the JTAG interface for common SW debug adding all the system TAPs to the

chain.

NC These signals are No Connect (NC) and should be disconnected by the user.

POR_B This cold reset negative logic input resets all modules and logic in the IC.

May be used in addition to internally generated power on reset signal (logical AND, both internal

and external signals are considered active low).

ONOFF ONOFF can be configured in debounce, off to on time, and max time-out configurations. The

debounce and off to on time configurations supports 0, 50, 100 and 500 ms. Debounce is used to

generate the power off interrupt. While in the ON state, if ONOFF button is pressed longer than the

debounce time, the power off interrupt is generated. Off to on time supports the time it takes to

request power on after a configured button press time has been reached. While in the OFF state,

if ONOFF button is pressed longer than the off to on time, the state will transition from OFF to ON.

Max time-out configuration supports 5, 10, 15 seconds and disable. Max time-out configuration

supports the time it takes to request power down after ONOFF button has been pressed for the

defined time.

TEST_MODE TEST_MODE is for NXP factory use. The user must tie this pin directly to GND.

Table 4. JTAG Controller Interface Summary

JTAG I/O Type On-chip Termination

JTAG_TCK Input 47 k

pull-up

JTAG_TMS Input 47 kpull-up

JTAG_TDI Input 47 kpull-up

JTAG_TDO 3-state output Keeper

JTAG_TRSTB Input 47 kpull-up

JTAG_MOD Input 100 kpull-up

Table 3. Special Signal Considerations (continued)

Signal Name Remarks

剩余138页未读，继续阅读

hnzqd

粉丝: 0
资源: 2

NXP i.MX6ULL处理器数据手册：高性能多媒体平台

IMX6DQRM.pdf.zip

IMX6DQRM.pdf

IMX6SDLRM.pdf

IMX6ULLRM.pdf

imx6开发板.pdf

IMX6ULRM.pdf

IMX6SDLCEC.pdf

IMX6SLRM.pdf

IMX6DQAEC.pdf

imx185lqj.pdf

最新资源