stm32f407点灯代码
时间: 2023-09-15 17:23:44 浏览: 53
这是一个关于STM32F407点灯的示例代码:
#include "stm32f4xx.h"
int main(void)
{
// Enable GPIOA Peripheral clock
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
// Configure PA5 as output push-pull
GPIO_InitTypeDef GPIO_InitStruct;
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_5;
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOA, &GPIO_InitStruct);
while(1)
{
// Toggle LED on PA5
GPIO_ToggleBits(GPIOA, GPIO_Pin_5);
// Delay
for(uint32_t i=0; i < 1000000; i++);
}
}
相关问题
STM32F106最小系统点灯代码
以下是使用STM32F106最小系统点亮LED的代码,使用的是GPIOB的第0个引脚作为输出口:
```
#include "stm32f10x.h" // 包含STM32F10x系列单片机的头文件
int main(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE); // 使能GPIOB时钟
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0; // 选择要控制的引脚
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; // 设置引脚为推挽输出
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; // 设置引脚输出速率为50MHz
GPIO_Init(GPIOB, &GPIO_InitStructure); // 初始化GPIOB
while(1)
{
GPIO_SetBits(GPIOB, GPIO_Pin_0); // 点亮LED
for(int i=0; i<1000000; i++); // 延时一段时间
GPIO_ResetBits(GPIOB, GPIO_Pin_0); // 熄灭LED
for(int i=0; i<1000000; i++); // 延时一段时间
}
}
```
上述代码将GPIOB的第0个引脚设置为推挽输出,然后不停地点亮和熄灭LED。您可以根据需要更改GPIO引脚的配置和延时时间。
帮我写个点灯代码,用stm32f407zet6
好的,以下是一个简单的点灯代码,使用了STM32F407ZET6的GPIO模块:
```c
#include "stm32f4xx.h"
#define LED_PIN GPIO_Pin_13
#define LED_PORT GPIOD
int main(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
// 使能 GPIOD 时钟
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
// 配置 LED 引脚为输出
GPIO_InitStructure.GPIO_Pin = LED_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(LED_PORT, &GPIO_InitStructure);
while (1)
{
// 点亮 LED
GPIO_SetBits(LED_PORT, LED_PIN);
// 等待一段时间
for (int i = 0; i < 0x1FFFFF; i++);
// 熄灭 LED
GPIO_ResetBits(LED_PORT, LED_PIN);
// 等待一段时间
for (int i = 0; i < 0x1FFFFF; i++);
}
}
```
该代码会不断循环地点亮和熄灭LED。你可以根据需要修改代码,例如更改LED引脚的定义,或者调整等待时间。