基于rs485的简单现场总线通信系统实现单发单收
时间: 2023-12-01 07:04:36 浏览: 33
好的,针对您的问题,我可以给出以下的步骤:
1. 搭建rs485通信系统的硬件环境,包括使用一个rs485转ttl模块,将其连接到单片机的串口口线,同时使用两个终端电阻将rs485总线两端地接,以确保传输线路的正确性。
2. 编写单片机程序,使用单片机的串口发送数据,并接收来自其他设备的数据。在发送数据时,需要将数据按照rs485的通信协议进行格式化,并将通信模式设置为单发单收。
3. 调试程序,确保单片机能够正常的发送和接收数据。可以使用串口调试工具,如TeraTerm等软件进行测试。
4. 在实际应用中,需要将单片机与其他设备进行连接,如传感器、执行器等。需要根据不同设备的接口类型,进行相应的接线和协议配置。
需要注意的是,在实际应用中,还需要考虑到通信的可靠性和数据的安全性,如使用CRC校验等机制来保证数据的完整性和正确性,以及进行加密等操作来保护数据的安全性。
相关问题
基于rs485的简单现场总线通信系统单发单收c语言程序
以下是基于RS485的简单现场总线通信系统的单发单收C语言程序示例:
```c
#include <stdio.h>
#include <stdlib.h>
#include <fcntl.h>
#include <unistd.h>
#include <termios.h>
#define BAUDRATE B9600
#define MODEMDEVICE "/dev/ttyS0"
#define _POSIX_SOURCE 1
int set_interface_attribs(int fd, int speed)
{
struct termios tty;
if (tcgetattr(fd, &tty) < 0) {
printf("Error from tcgetattr: %s\n", strerror(errno));
return -1;
}
cfsetospeed(&tty, (speed_t)speed);
cfsetispeed(&tty, (speed_t)speed);
tty.c_cflag |= (CLOCAL | CREAD);
tty.c_cflag &= ~CSIZE;
tty.c_cflag |= CS8;
tty.c_cflag &= ~PARENB;
tty.c_cflag &= ~CSTOPB;
tty.c_cflag &= ~CRTSCTS;
tty.c_lflag &= ~(ICANON | ECHO | ECHOE | ISIG);
tty.c_iflag &= ~(IXON | IXOFF | IXANY);
tty.c_iflag &= ~(IGNBRK|BRKINT|PARMRK|ISTRIP|INLCR|IGNCR|ICRNL);
tty.c_oflag &= ~OPOST;
tty.c_cc[VTIME] = 0;
tty.c_cc[VMIN] = 1;
if (tcsetattr(fd, TCSANOW, &tty) != 0) {
printf("Error from tcsetattr: %s\n", strerror(errno));
return -1;
}
return 0;
}
void set_blocking(int fd, int should_block)
{
struct termios tty;
memset(&tty, 0, sizeof(tty));
if (tcgetattr(fd, &tty) != 0) {
printf("Error from tggetattr: %s\n", strerror(errno));
return;
}
tty.c_cc[VMIN] = should_block ? 1 : 0;
tty.c_cc[VTIME] = 5;
if (tcsetattr(fd, TCSANOW, &tty) != 0)
printf("Error setting term attributes: %s\n", strerror(errno));
}
int main(int argc, char *argv[])
{
int fd;
char buf[256];
char *portname = MODEMDEVICE;
if (argc > 1) {
portname = argv[1];
}
fd = open(portname, O_RDWR | O_NOCTTY | O_SYNC);
if (fd < 0) {
printf("Error opening %s: %s\n", portname, strerror(errno));
return -1;
}
set_interface_attribs(fd, BAUDRATE);
set_blocking(fd, 0);
// 发送数据
char send_buf[] = "Hello, RS485!";
write(fd, send_buf, sizeof(send_buf));
// 接收数据
int n = read(fd, buf, sizeof(buf));
if (n > 0) {
buf[n] = 0;
printf("Received %d bytes: %s\n", n, buf);
}
close(fd);
return 0;
}
```
在这里,我们使用了Linux下的串口通信库`termios`。`set_interface_attribs`函数设置了串口的参数,包括波特率、数据位、停止位等。`set_blocking`函数设置了串口的阻塞方式,如果`should_block`为1表示阻塞读取,否则表示非阻塞读取。在`main`函数中,我们先打开串口设备,然后发送一条数据,再接收一条数据。注意,在RS485总线上,需要在发送和接收数据前进行总线控制,具体方法可以参考RS485总线的通信协议。
基于stc90c516rd单片机rs485简单现场总线通信系统实现单发单收从0~99的发送程序和接收程序
好的,以下是基于stc90c516rd单片机rs485串口通信实现单发单收从0~99的发送程序和接收程序代码示例:
发送程序:
```
#include <reg52.h>
#include <intrins.h>
#define uchar unsigned char
#define uint unsigned int
sbit RS485_EN = P1^7; //定义RS485使能端口
void InitUart(void)
{
SCON = 0x50; //设置串口工作方式
TMOD = 0x20; //设置定时器工作方式
TH1 = 0xfd; //设置波特率为9600
TL1 = 0xfd;
TR1 = 1; //启动定时器1
ES = 1; //使能串口中断
EA = 1; //使能总中断
}
void SendData(uchar dat)
{
SBUF = dat; //将数据放入发送缓冲区
while(!TI); //等待发送完成
TI = 0; //清零发送完成标志
}
void SendCmd(uchar cmd)
{
RS485_EN = 0; //将RS485芯片使能
SendData(cmd); //发送指令
RS485_EN = 1; //关闭RS485芯片使能
}
void main()
{
InitUart(); //初始化串口
while(1)
{
uchar i;
for(i=0; i<100; i++)
{
SendCmd(i); //发送数据
delay(1000); //延时1秒
}
}
}
void UartIsr() interrupt 4
{
uchar dat;
if(RI) //接收到数据
{
RI = 0; //清零接收标志
dat = SBUF; //读取接收缓冲区数据
}
}
```
接收程序:
```
#include <reg52.h>
#include <intrins.h>
#define uchar unsigned char
#define uint unsigned int
sbit RS485_EN = P1^7; //定义RS485使能端口
void InitUart(void)
{
SCON = 0x50; //设置串口工作方式
TMOD = 0x20; //设置定时器工作方式
TH1 = 0xfd; //设置波特率为9600
TL1 = 0xfd;
TR1 = 1; //启动定时器1
ES = 1; //使能串口中断
EA = 1; //使能总中断
}
void SendData(uchar dat)
{
SBUF = dat; //将数据放入发送缓冲区
while(!TI); //等待发送完成
TI = 0; //清零发送完成标志
}
void SendCmd(uchar cmd)
{
RS485_EN = 0; //将RS485芯片使能
SendData(cmd); //发送指令
RS485_EN = 1; //关闭RS485芯片使能
}
void main()
{
InitUart(); //初始化串口
while(1)
{
uchar dat;
if(RI) //接收到数据
{
RI = 0; //清零接收标志
dat = SBUF; //读取接收缓冲区数据
//处理接收到的数据
}
}
}
void UartIsr() interrupt 4
{
uchar dat;
if(RI) //接收到数据
{
RI = 0; //清零接收标志
dat = SBUF; //读取接收缓冲区数据
}
}
```
在程序中,发送程序通过 `SendCmd` 函数发送数据,接收程序通过串口中断接收数据,并在 `main` 函数中处理接收到的数据。需要注意的是,在发送数据时需要将 `RS485_EN` 置为 0,将芯片使能,发送完成后再将其置为 1,关闭芯片使能。在实际使用中,还需要根据具体的硬件连接和协议规定进行适当的修改。
相关推荐
![](https://img-home.csdnimg.cn/images/20210720083646.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)