请帮我解释以下内容的意思:[Huawei]display eth-trunk Eth-Trunk12's state information is: Local: LAG ID: 12 WorkingMode: STATIC Preempt Delay Time: 30 Hash arithmetic: According to SIP-XOR-DIP System Priority: 123 System ID: 4c1f-cc70-5809 Least Active-linknumber: 1 Max Active-linknumber: 2 Operate status: up Number Of Up Port In Trunk: 2 -------------------------------------------------------------------------------- ActorPortName Status PortType PortPri PortNo PortKey PortState Weight GigabitEthernet0/0/1 Unselect 1GE 40000 2 3121 10100000 1 GigabitEthernet0/0/2 Selected 1GE 32768 3 3121 10111100 1 GigabitEthernet0/0/3 Selected 1GE 32768 4 3121 10111100 1 Partner: -------------------------------------------------------------------------------- ActorPortName SysPri SystemID PortPri PortNo PortKey PortState GigabitEthernet0/0/1 32768 4c1f-ccdb-3790 32768 2 3121 10100000 GigabitEthernet0/0/2 32768 4c1f-ccdb-3790 32768 3 3121 10111100 GigabitEthernet0/0/3 32768 4c1f-ccdb-3790 32768 4 3121 10111100
时间: 2023-09-16 12:16:18 浏览: 100
这段内容是华为交换机命令行界面下的输出信息,展示了一个名为 Eth-Trunk12 的以太网聚合接口的状态信息。其中包括该聚合接口的配置信息(如聚合ID、工作模式、哈希算法、系统优先级等),以及当前聚合组中各物理接口的状态信息(如端口名称、状态、端口类型、优先级、端口号、端口权重等)。还展示了聚合组的 Partner 信息,包括对端物理接口的状态信息。这些信息可以帮助系统管理员了解聚合组的状态和性能表现。
相关问题
华为交换机eth-trunk配置
要配置华为交换机的eth-trunk,需要执行以下步骤:
1. 创建eth-trunk接口:在交换机的全局配置模式下,使用以下命令创建eth-trunk接口:
```
interface eth-trunk <trunk id>
```
其中,trunk id为eth-trunk的编号,可以是任何数字或字母组合。
2. 向eth-trunk接口添加物理端口:使用以下命令将物理端口添加到eth-trunk接口中:
```
interface GigabitEthernet <interface id>
port link-type trunk
port trunk allow-pass vlan <vlan id>
```
其中,interface id为物理端口的编号,vlan id为需要通过eth-trunk传输的VLAN ID。
3. 配置eth-trunk的工作模式和链路聚合方式:使用以下命令配置eth-trunk的工作模式和链路聚合方式:
```
mode lacp|manual
```
其中,lacp表示使用LACP协议进行链路聚合,manual表示手动配置链路聚合。
4. 配置eth-trunk的负载均衡方式:使用以下命令配置eth-trunk的负载均衡方式:
```
load-balance <mode>
```
其中,mode为负载均衡的方式,可以是src-ip、dst-ip、src-mac、dst-mac等。
5. 验证eth-trunk配置是否生效:使用以下命令查看eth-trunk接口的状态:
```
display interface eth-trunk <trunk id>
```
如果eth-trunk接口的状态为UP,则表示配置成功。
华三和华为交换机eth-trunk接口内子接口的配置命令详细步骤
华三和华为交换机的eth-trunk接口内子接口配置命令步骤如下:
华三交换机:
1. 创建eth-trunk聚合接口,使用命令: interface eth-trunk <trunk_id>。
2. 进入eth-trunk聚合接口视图,使用命令: interface eth-trunk <trunk_id>。
3. 创建子接口,使用命令: sub-interface <sub_id>。
4. 配置子接口的vlan属性,使用命令: vlan <vlan_id>。
5. 配置子接口的ip地址,使用命令: ip address <ip_address> <mask>。
6. 配置子接口的协议状态,使用命令: protocol <protocol_type>。
华为交换机:
1. 创建eth-trunk聚合接口,使用命令: interface eth-trunk <trunk_id>。
2. 进入eth-trunk聚合接口视图,使用命令: interface eth-trunk <trunk_id>。
3. 创建子接口,使用命令: interface eth-trunk <trunk_id>.<sub_id>。
4. 配置子接口的vlan属性,使用命令: vlan-type dot1q <vlan_id>。
5. 配置子接口的ip地址,使用命令: ip address <ip_address> <mask>。
6. 配置子接口的协议状态,使用命令: protocol <protocol_type>。
注意:在华为交换机上,子接口名称需要使用“eth-trunk <trunk_id>.<sub_id>”的格式。而在华三交换机上,子接口名称只需要使用“<sub_id>”的格式即可。