stm32数据采集代码
时间: 2023-08-18 21:05:23 浏览: 43
以下是一个基于 STM32 的数据采集示例代码,可以读取 ADC 转换器的值并将其发送到串口。
```c
#include "stm32f4xx.h"
#include "stdio.h"
#define ADC_PORT GPIOA
#define ADC_PIN GPIO_Pin_0
void ADC_Configuration(void);
void USART_Configuration(void);
void USART_puts(char *str);
int main(void)
{
uint16_t adc_value;
char str[50];
ADC_Configuration();
USART_Configuration();
while (1)
{
ADC_SoftwareStartConv(ADC1);
while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC));
adc_value = ADC_GetConversionValue(ADC1);
sprintf(str, "ADC Value: %d\r\n", adc_value);
USART_puts(str);
// 延时等待下一次采集
for (int i = 0; i < 500000; i++);
}
}
void ADC_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
ADC_InitTypeDef ADC_InitStructure;
// 使能 GPIOA 时钟
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
// 配置 ADC 输入引脚
GPIO_InitStructure.GPIO_Pin = ADC_PIN;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(ADC_PORT, &GPIO_InitStructure);
// 使能 ADC1 时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
// 配置 ADC1
ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
ADC_InitStructure.ADC_ScanConvMode = DISABLE;
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE;
ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfConversion = 1;
ADC_Init(ADC1, &ADC_InitStructure);
// 配置 ADC1 通道 0
ADC_RegularChannelConfig(ADC1, ADC_Channel_0, 1, ADC_SampleTime_3Cycles);
// 使能 ADC1
ADC_Cmd(ADC1, ENABLE);
}
void USART_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
// 使能 GPIOA 和 USART1 时钟
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
// 配置 USART1 引脚
GPIO_PinAFConfig(GPIOA, GPIO_PinSource9, GPIO_AF_USART1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_USART1);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9 | GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置 USART1
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 使能 USART1 发送
USART_Cmd(USART1, ENABLE);
}
void USART_puts(char *str)
{
while (*str != '\0')
{
while(USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET);
USART_SendData(USART1, *str++);
}
}
```
在上面的示例代码中,首先进行了 GPIO 和 ADC 的初始化配置,并在 while 循环中进行数据采集和串口发送。需要注意的是,串口的配置和发送函数可以根据具体的需求进行修改。