uint8t和char的区别
时间: 2024-06-05 22:08:19 浏览: 11
uint8_t 是一个无符号的 8 位整数类型 C++ 中可定义在 <cstdint> 头文件。char 是一个字符类型,在 C++ 中可在 <cstdio> 头文件中。它们的主要区别在于 uint8_t 是一个整数类型,而 char 是一个字符类型。另外,char 的取值范围为 -128 到 127,而 uint8_t 的取值范围为 0 到 255。
相关问题
stm32c8t6配置串口二和ch340通信
好的,我可以为您提供一些关于STM32C8T6配置串口2和CH340通信的建议。
首先,您需要确保已经正确地连接了CH340串口转USB模块和STM32C8T6开发板。然后,您需要使用STM32C8T6的库函数来配置串口2的参数,例如波特率、停止位、数据位等等。下面是一个简单的示例代码,可以将波特率设置为9600,数据位为8位,无奇偶校验,停止位为1位:
```
#include "stm32f10x.h"
#include "stdio.h"
void USART2_Config(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART2, &USART_InitStructure);
USART_Cmd(USART2, ENABLE);
}
```
然后,您需要使用串口发送和接收函数来与CH340通信。您可以使用标准的C库函数,例如`fputc()`和`fgetc()`,也可以使用STM32C8T6库函数,例如`USART_SendData()`和`USART_ReceiveData()`。下面是一个简单的示例代码,可以发送一个字符串并从串口接收一个字符:
```
#include "stm32f10x.h"
#include "stdio.h"
void USART2_SendString(char* str)
{
while (*str)
{
USART_SendData(USART2, (uint16_t) *str++);
while (USART_GetFlagStatus(USART2, USART_FLAG_TXE) == RESET);
}
}
int USART2_GetChar(void)
{
while (USART_GetFlagStatus(USART2, USART_FLAG_RXNE) == RESET);
return (int) USART_ReceiveData(USART2);
}
int main(void)
{
USART2_Config();
USART2_SendString("Hello, CH340!\r\n");
int ch = USART2_GetChar();
return 0;
}
```
希望这些代码能够帮助您完成STM32C8T6配置串口2和CH340通信的任务。如果您遇到任何问题,请随时向我提问。
写一个stm32c8t6 的串口1 接收和发送的函数
下面是一个示例代码,用于在STM32C8T6上编写串口1的接收和发送函数:
```c
#include "stm32f10x.h"
#define BUFFER_SIZE 128
volatile uint8_t rxBuffer[BUFFER_SIZE];
volatile uint8_t rxIndex = 0;
void USART1_IRQHandler(void) {
if (USART_GetITStatus(USART1, USART_IT_RXNE) != RESET) { // 检查是否接收到数据
uint8_t data = USART_ReceiveData(USART1); // 读取接收到的数据
if (rxIndex < BUFFER_SIZE) {
rxBuffer[rxIndex++] = data; // 存储数据到接收缓冲区
}
}
}
void USART1_SendByte(uint8_t data) {
while (USART_GetFlagStatus(USART1, USART_FLAG_TC) == RESET); // 等待发送缓冲区为空
USART_SendData(USART1, data); // 发送数据
}
void USART1_SendString(const char* str) {
while (*str) {
USART1_SendByte(*str++);
}
}
int main(void) {
USART_InitTypeDef USART_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// 使能串口1时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
// 使能GPIOA时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
// 配置PA9作为USART1的TX引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置PA10作为USART1的RX引脚
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// 配置USART1
USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART1, &USART_InitStructure);
// 配置USART1接收中断
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
// 使能USART1接收中断
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
// 使能USART1
USART_Cmd(USART1, ENABLE);
while (1) {
// 在这里可以处理接收到的数据
if (rxIndex > 0) {
// 处理接收缓冲区中的数据
// ...
rxIndex = 0; // 清空接收缓冲区索引
}
// 发送数据示例
USART1_SendString("Hello, World!\r\n");
}
}
```
以上代码演示了如何在STM32C8T6上配置和使用USART1进行串口接收和发送。在USART1的中断处理函数中(`USART1_IRQHandler`),通过检查`USART_GetITStatus(USART1, USART_IT_RXNE)`来判断是否接收到数据。如果接收到数据,使用`USART_ReceiveData(USART1)`读取接收到的数据,并将其存储到接收缓冲区`rxBuffer`中。
在主函数中,可以通过处理接收缓冲区的数据来进行相应的操作。请注意,这只是一个示例,你可以根据自己的需求进行进一步的处理。同时,`USART1_SendByte()`函数用于发送单个字节数据,`USART1_SendString()`函数用于发送字符串数据。在示例中,发送了"Hello, World!\r\n"字符串。记得根据实际情况修改波特率和其他参数。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![txt](https://img-home.csdnimg.cn/images/20210720083642.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)