stm32当温度超过阈值led灯亮
时间: 2023-12-20 16:04:58 浏览: 81
以下是使用STM32实现当温度超过阈值时LED灯亮的示例代码:
```c
#include "stm32f4xx.h"
#define THRESHOLD_TEMP 25 // 温度阈值
int main(void)
{
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE); // 使能GPIOA时钟
GPIO_InitTypeDef GPIO_InitStruct;
GPIO_InitStruct.GPIO_Pin = GPIO_Pin_5; // 使用PA5控制LED灯
GPIO_InitStruct.GPIO_Mode = GPIO_Mode_OUT; // 设置GPIOA为输出模式
GPIO_InitStruct.GPIO_OType = GPIO_OType_PP; // 设置输出类型为推挽输出
GPIO_InitStruct.GPIO_Speed = GPIO_Speed_100MHz; // 设置输出速率为100MHz
GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL; // 不使用上下拉电阻
GPIO_Init(GPIOA, &GPIO_InitStruct); // 初始化GPIOA
ADC_InitTypeDef ADC_InitStruct;
ADC_CommonInitTypeDef ADC_CommonInitStruct;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE); // 使能ADC1时钟
ADC_CommonInitStruct.ADC_Mode = ADC_Mode_Independent; // ADC独立模式
ADC_CommonInitStruct.ADC_Prescaler = ADC_Prescaler_Div2; // ADC时钟分频为2
ADC_CommonInitStruct.ADC_DMAAccessMode = ADC_DMAAccessMode_Disabled; // 不使用DMA
ADC_CommonInitStruct.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles; // 设置采样延迟为5个时钟周期
ADC_CommonInit(&ADC_CommonInitStruct);
ADC_InitStruct.ADC_Resolution = ADC_Resolution_12b; // 12位分辨率
ADC_InitStruct.ADC_ScanConvMode = DISABLE; // 禁止扫描模式
ADC_InitStruct.ADC_ContinuousConvMode = ENABLE; // 开启连续转换模式
ADC_InitStruct.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_None; // 不使用外部触发
ADC_InitStruct.ADC_DataAlign = ADC_DataAlign_Right; // 数据右对齐
ADC_InitStruct.ADC_NbrOfConversion = 1; // 一次转换
ADC_Init(ADC1, &ADC_InitStruct); // 初始化ADC1
ADC_RegularChannelConfig(ADC1, ADC_Channel_TemperatureSensor, 1, ADC_SampleTime_84Cycles); // 配置温度传感器为ADC通道,并设置采样时间
ADC_Cmd(ADC1, ENABLE); // 使能ADC1
while(1)
{
ADC_SoftwareStartConv(ADC1); // 开始转换
while(!ADC_GetFlagStatus(ADC1, ADC_FLAG_EOC)); // 等待转换结束
int16_t temp = ADC_GetConversionValue(ADC1); // 获取温度传感器的转换值
float temperature = (float)(temp - (float)0.76) / (float)0.0025 + 25.0; // 根据转换值计算温度
if(temperature > THRESHOLD_TEMP) // 如果温度超过阈值
{
GPIO_SetBits(GPIOA, GPIO_Pin_5); // 点亮LED灯
}
else
{
GPIO_ResetBits(GPIOA, GPIO_Pin_5); // 熄灭LED灯
}
for(int i = 0; i < 100000; i++); // 延时一段时间
}
}
```
这段代码使用了STM32的ADC模块来读取温度传感器的值,并计算出实际温度。然后根据温度是否超过阈值来控制LED灯的亮灭。注意,在使用温度传感器进行温度测量时,需要先对ADC进行校准。具体方法可参考STM32的官方文档。
相关推荐
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![zip](https://img-home.csdnimg.cn/images/20210720083736.png)
![pdf](https://img-home.csdnimg.cn/images/20210720083512.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)
![](https://csdnimg.cn/download_wenku/file_type_ask_c1.png)